To prevent accidental actuation and limit access to sensitive equipment, these switches require a key to turn circuits on or off. The contact block and actuator are all one piece, so they won’t separate in high-vibration applications. Install them in a standard panel cutout. They’re keyed alike, so they will all open with the same key.

For technical drawings and 3-D models, click on a part number.

Use fingerprints to confirm the identity of personnel before granting access to secure areas or equipment. Switches light up green to indicate that they have accepted the fingerprint and are sending an output signal. The front faces of the switches meet NEMA 12 and IP65. The rear faces of the switches meet IP20.

Covers (sold separately) have an adhesive-back hinge, so you can stick them on to your switch. Keep the cover flipped down to protect the switch’s sensor from dust and debris.

For technical drawings and 3-D models, click on a part number.

Rated NEMA 6P, 12, IP68 and IP69K, these switches protect against corrosion and high-pressure, high-temperature washdowns. Also known as capacitive proximity switches, they remotely sense both metallic and nonmetallic objects but their strength is in sensing materials such as plastic, ceramic, and clear targets. They’re often used with programmable logic controllers (PLCs) and produce PNP or NPN signal output. To determine the signal output of a switch you are replacing, use Testers for Proximity and Photoelectric Switches (not included). They mount flush with the surface of any material, including metal, and are also known as embeddable or shielded switches. The 4-pole Micro M12 plug connects to cables with sockets (sold separately), allowing you to quickly connect and disconnect the switch.

Also available: If you don’t see the switch you need, please select 6693T999 and specify manufacturer and manufacturer part number.

For technical drawings and 3-D models, click on a part number.

Wire contacts to an alarm system to alert when doors or windows are opened. Mount the magnet to the door or window and mount the switch to the frame. The alarm will activate when the magnet is pulled away by the opening door or window.

SPDT switches connect to an alarm system and to another device, such as a motion detector.

Install these switches in areas with oil, coolant, corrosive chemicals, and regular washdowns. They're rated IP69K and NEMA 4X and 12 or 12K. Since they’re already protected inside a housing, you can mount them to a wall if there’s no space left in your electrical panel. You need to grip and twist the lever to actuate, so they won’t accidentally turn on or off if something bumps into them. To lock them in the off position, attach a padlock (not included) to the lever. Use these switches to turn motors on and off, or with other circuits such as lighting and electric heat circuits. They do not provide overload protection.

Switches with a plastic housing can be turned into a handheld control for moving around your workstation by attaching a cord and cord grip. The housing is PBT polyester, so it won’t swell in moist environments.

Switches with a power indicator use LED lights to show the status of power flowing into the switch and power flowing from the switch to your motor. This can help you check for issues, such as a welded contact or phase loss, without having to open the housing.

For technical drawings and 3-D models, click on a part number.

Combine a switch with a thermal overload element to build a starter that can handle high-current-rated motors. All are housed in a durable steel enclosure. They’re also known as NEMA starters.

NEMA 12 rated switches are protected from oil/coolant dripping.

Thermal overload elements shut motors off if current exceeds the full-load current rating. Three elements are required. To Order: Please specify the full-load current rating of your motor. If the full-load current rating is not shown on the motor’s faceplate, estimate the current rating (given the motor’s horsepower and voltage).

For technical drawings and 3-D models, click on a part number.

Rated NEMA 4, these controls are protected from washdowns. Set them to automatically adjust motor speed. Wire a potentiometer (not included) for remote manual control.

Controls rated NEMA 12 also protect against splashes of oil and coolant when used indoors.

For technical drawings and 3-D models, click on a part number.

Cut power and keep it isolated to prevent equipment from starting up during inspection and maintenance. These switches are housed in a protective enclosure that resists denting, chipping, and cracking. Mount them to the wall when you run out of space in an electrical panel.

Switches with lockout secure in the off position with a padlock with a maximum shackle diameter of 5/16” (not included).

Photovoltaic switches can be used with photovoltaic cells which convert sunlight into electricity.

Add auxiliary contact blocks to send a signal or connect to another device, such as an alarm or indicating light.

Use additional power poles to control more than three circuits. Add neutral poles to open and close the neutral leg of a three phase system.

For technical drawings and 3-D models, click on a part number.

Keep power running while you access your enclosure. Unlike standard enclosure disconnect switches, which shut off power as you open your enclosure, these have an override function. Engaging the override allows you to take voltage reading, troubleshoot an error code, or fine tune the speed of your line. When the override is off, these work like a standard disconnect switch—a safety interlock prevents your enclosure from opening when power is on. The interlock also prevents the switch from turning on when the door is already open. Cut the shaft to fit your enclosure. All have a lockout so you can secure them in the off position with a padlock (not included).

Add auxiliary contact blocks to send a signal or connect to another device, such as an alarm or indicating light.

Use additional power poles to control more than three circuits. Add neutral poles to open and close the neutral leg of a three-phase system.

Add junction blocks to connect a ground wire.

Terminal covers prevent contact with live terminals.

For technical drawings and 3-D models, click on a part number.