Springs in these hinges with holes automatically swing doors and gates closed behind you.

After a light push on the door, springs in these hinges swing doors and gates fully open.

Use these hinges on lightweight screen and storm doors as well as small gates.

Open doors past their frame to make extra room for people and large items, such as carts, furniture, and wheelchairs, to pass through.

Hinge leaves fit into two cutouts (mortises) to mount flush with the door and frame.

Made of plastic with a metal additive, these hinges will set off metal detectors if a piece breaks off and falls into your line.

Thick leaves and a large diameter pin make these hinges good for use with heavy doors.

These hinges are made of metal.

Thick leaves and a large diameter pin make these hinges good for use with heavy doors.

Tighten or loosen an adjustment screw to change the hinge resistance.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

Eliminate slamming lids—these hinges hold lids open at their widest angle and then slowly pull them closed.

These hinges are made of metal.

Hinge leaves fit into two cutouts (mortises) to mount flush with the door and frame.

A grease fitting makes these hinges easy to lubricate.

These hinges are made of metal.

Remove the ring to pull out the pin.

These hinges with holes are spring loaded—pull the handle to retract the pin and disconnect a door; release the handle and the pin snaps back.

A keeper holds the pin in a retracted position to make reconnecting doors easier than other pull-release quick-disconnect hinges.

Lock these hinges open at any angle within their range of motion.

One leaf mounts around the edge of the door for a secure hold, while the other mounts to the frame.

The mounting hole pattern does not follow an industry standard, which means you can work around worn mounting holes when replacing template hinges.

A stud projects from the back of each hinge leaf to prevent the door from being forced open. The mounting holes form an industry-standard half-moon shape.

The mounting holes on these hinges form an industry-standard half-moon shape.

Longer than other entry door hinges, these piano-style hinges run the entire length of doors for strength and durability.

Only one cutout (mortise) is needed to mount these hinges—the offset design allows surface mounting the door leaf and mortise mounting the frame leaf.

The hinge pin is permanently attached to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

The mounting hole pattern does not follow an industry standard, which means you can work around worn mounting holes when replacing template hinges.

Also known as gravity hinges, the weight of the door returns these hinges to a closed position without the help of springs.

The hinge pin is permanently attached to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

The leaves of these hinges almost touch when the door is closed. They are often used in electrical enclosures for a tight seal.

Choose these hinges for their adherence to strict military standards for material and construction.

Made of carbon fiber, these hinges are as strong as aluminum yet lighter in weight. All have leaves that are connected by a strip of flexible Kevlar instead of a pin.

These hinges are made of metal.

These hinges are made of metal.

With large pin diameters for added strength, these hinges can hold heavier doors and gates than other strap hinges.

The hinge pin attaches to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

Bearings allow these hinges to open and close doors smoothly.

Spring tension pulls the door closed when it’s open less than 10° and keeps it closed without a catch or latch.

Eliminate slamming doors—push the door and these hinges slowly pull it closed.

These hinges have a standard range of motion of 100° to 120°.

Easier to install than other mortise-mount concealed cabinet hinges, these fit in two drilled holes.

Hinge leaves fit into two cutouts (mortises) to mount flush with door and frame edges.

When the cabinet door is closed, a portion of the frame leaf is exposed and the entire door leaf is hidden

Use hinges to add doors, lids, and machine guards to T-slotted framing.

Build test fixtures, prototypes, and other small structures with this miniature version of T-slotted framing and fittings.

Hold two pieces of strut channel together so they can smoothly open or close.

These sets include a left-hand and right-hand bracket for creating folding tables.