We will reply to your message within an hour.
A double hinge provides high cutting force with low gripping pressure. These cutters are also known as aviation snips.
Keep your hand away from the material being cut.
Blades are high-speed steel so they stay sharp longer than steel blades, and they can be sharpened.
The handles are angled 90° from the blade so you can cut material from directly above tight spaces.
This cutter has two blades that cut a 1/8" wide strip—peel it back for smooth edges with little distortion.
Prevent waste from flying up as you work. A double blade makes two cuts to create a 7/64"-wide step that peels back, leaving little distortion and smooth edges.
These cutters make straight cuts and curves.
Also known as bulldog snips, these have long handles and short blades for cutting through thick sheet metal with less effort than standard sheet metal cutters.
Blades are tapered to give you more control when cutting straight lines, tight curves, and circles, and they're serrated to prevent slipping. These cutters are also known as duckbill snips.
Replace blades as they wear. These cutters are also known as tinners' snips.
Handles are angled to keep your hand away from the material as you cut straight lines and curves.
Made from aluminum bronze, the blade and handle on these cutters inhibit sparking and are FM approved. Use them for straight cuts.
Loosen a few screws to swap dull blades with new ones. These cutters have offset handles to keep your hands clear of the metal being cut.
Sized and shaped like pliers, these sheet metal cutters are small enough to fit in your tool belt.
Make round, square, and irregular-shaped holes with this punch-style hole cutter.
Cut up to 1" deep V-shaped notches in sheet metal.
A double blade creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.
Use to cut patterns in flat material with minimal material loss and less effort compared to manual cutters.
Punch small pieces out of material to create an almost burr-free cut with no material distortion.
Minimize material loss and edge distortion with these scissor-like cutters that cut metal up to 1/64" thick.+
These nibblers punch small pieces out of material to create an almost burr-free cut with no material distortion.
Also known as slotting shears, these cutters have a double blade that creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.
Also known a scissor-blade shears, the bottom blade remains stationary while the upper blade moves up and down to cut metal up to 1/64" thick with minimal material loss and edge distortion.
Turn your portable drill into a punch cutter for cutting curved and straight shapes in flat and corrugated sheet metal and plastic.
Make straight, clean cuts in thick sheet metal.
A 12" long blade makes long, straight cuts in thin metals and flexible materials. Not for use on phenolic or other rigid materials.
This large-capacity cutter has a 25" blade for long, straight cuts.
Combine the cutting base and a corner punch to make rounded corners in sheet metal.
Turn your workpiece while cutting to create curves and complex shapes.
Notch, cut, and pierce a variety of materials including metal, plastic, and vinyl.
Make straight cuts in sheets. These cutters are foot operated so your hands are free to position the material.
Leave clean cut edges in a variety of pliable materials.
These high-speed steel saws cuts through aluminum, brass, bronze, and steel.
Make clean, fast cuts in thin metal and plastic when you use one of these saws with an impact driver. The body widens at the top to prevent the saw from pushing through your workpiece.
An extra-thick steel body with carbide teeth can cut through stainless steel structural framing and electrical enclosures.
The carbide teeth on these steel saws cut aluminum, brass, bronze, steel, and plastic sheets and last up to twice as long as high-speed steel teeth.
These saws reduce friction and prevent material buildup when cutting fiberglass and plastic.
Attach these saws to your portable drill to cut a range of large diameter hole sizes in sheet metal.
Use these saws with a drill press to cut a variety of hole sizes in sheet metal.
Lower cutting depths than standard hole saws make these saws less likely to rip or tear while making smooth, burr-free cuts in sheets.
Designed to cut sheet metal.
Cut through the strong fibers of Kevlar.
For extra leverage to cut through Kevlar, metal, and plastics, these scissors have long handles and short blades.
After each cut, the jaws spring open to make continuous cutting easy.
Insulated handles protect against shock from accidental contact with live electrical circuits. These scissors are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.
Cut and strip wire in tight spaces with the compact tips on these scissors.
Also known as electricians' shears, the back edge of the blade has a file to clean contacts.
Protect sensitive equipment from harmful static discharges while cutting and stripping wire.
These small scissors have narrow, sharp tips for fine cutting and trimming.
Short blades make these scissors easy to maneuver in cramped areas for small, detailed cuts less than an inch long.
Prevent snags and injury with the rounded points on these small scissors.
Trim flush against a flat surface with the curved blades on these small scissors.
Make clean cuts through duct tape and other sticky materials.
Save space in your shop by cutting, bending, and curving sheet metal with a single machine. Also known as shear brake rolls.
Also known as 40‐ton metalworkers, these hydraulic machines handle a variety of forming tasks including pressing, punching, notching, and shearing.