We will reply to your message within an hour.
More
Nickel plating gives these magnets good corrosion resistance.
Cover these unfinished magnets with your choice of coating to prevent corrosion.
In addition to protecting magnets and mounting surfaces, a rubber coating gives these magnets a slip-resistant surface.
Even at temperatures up to 300° F, these magnets have strong holding power.
Many small poles give these magnets shallower, more concentrated magnetic fields that hold especially well on thin material. They resist temperatures up to 180° F.
Strong and compact, these rare earth magnets resist temperatures up to 570° F.
Ceramic magnets resist demagnetization better than other magnets and are an economical choice. They resist temperatures up to 400° F.
Made of neodymium, these rare earth magnets are the strongest for their size. Slide onto a rod or use a bolt or screw to install.
Many small poles give these magnets shallower, more concentrated magnetic fields that hold especially well on thin material.
Alnico magnets aren't as strong as rare earth magnets, but they withstand the highest temperatures—up to 970° F.
Press these magnets into place, or use them like a tongue and groove to align components. The stepped profile allows you to install them without adhesives or screws.
A steel case concentrates and focuses the magnetic field. It also protects the magnetic material.
A rubber cover protects the magnet and mounting surface.
Ceramic magnets resist demagnetization better than other magnets and are an economical choice. They resist temperatures up to 140° F.
These ceramic magnets resist demagnetization better than other magnets, and have a metal case to protect the magnetic material. They resist temperatures up to 175° or 245° F.
A metal case protects the magnetic material.
A rubber cover protects the mounting surface as well as the magnet.
Alnico magnets resist temperatures up to 420° F.
Press these magnets into a drilled hole so they are flush against the surface.
Rare earth samarium-cobalt offers a balance of strength and temperature resistance.
A case protects the magnetic material.
A plastic case protects the mounting surface as well as the magnet.
To add a magnetic surface anywhere, install the mounting plate, then screw on the magnet.
Ceramic magnets resist demagnetization better than other magnets and are an economical choice. They resist temperatures up to 480° F.
These magnets are bonded with epoxy resin, so they can be machined with carbide tooling.
Slide these magnets onto a rod or install with a bolt. They are bonded with epoxy resin, so they can be machined with carbide tooling.
Attach parts in the same place every time with these magnet pairs that center as they pull together.
These magnet pairs attract for a strong hold but repel when twisted for an easy release. Use them on doors, covers, and other parts that need to be repeatedly installed and removed.
These magnet pairs rotate into multiple positions to orient displays, sensors, and other devices. They have a firm hold at specific angles, but turn easily without detaching.
These discs are made of corrosion-resistant ceramic and bonded with rubber for flexibility.
Replace individual rods in an existing filter or create a custom filter.
These filters are designed without guide rods to prevent wet and sticky material from blocking flow.
Easy to keep clean thanks to their design, these filters pull metal and magnetic particles out of food and sanitary material as it passes through gravity hoppers, chutes, and other parts of your process line.
The guide rods direct flow to the magnetic rods. They’re helpful in removing dry particles from fine powder and low-flow applications.
Pull the rods from their sleeve to release particles stuck to the filter.
Keep coolant systems free of small particles, such as chip filings and metal dust.
Pick up screws, nuts, and other small steel objects.
A fluorescent orange handle makes these retrievers stand out, so they’re less likely to be misplaced.
Pick up heavier objects than our other magnetic retrievers. These retrievers have a long, fixed shaft, allowing you to reach material in hard-to-reach areas.
Often used to pick up steel sheets, the magnet holds material until you press the lever to disengage it.
LEDs light the magnetized tip for picking up screws, nuts, and other small steel objects in dark areas.
LEDs light the magnetized tip and the shaft bends and stays in position to reach objects in awkward spaces.
Protect against accidental contact with live electrical circuits. These insulated retrievers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505. The shaft bends and stays in position to reach objects in awkward spaces.
Push the plunger to engage the magnet; release to disengage. These retrievers bend into position and stay in place.
Bend the shaft to reach objects in awkward spaces.
Pick up heavier objects than our other flex-head magnetic retrievers. All of these retrievers have a long shaft and pivoting head to access hard-to-reach items from almost any angle.
The head pivots, so you can pick up screws, nuts, bolts, and other small steel objects from any angle.
Magnetized on all sides, these wand-like tools remove steel chips from machinery, the floor, and your clothing. Pull the plunger to demagnetize and drop the chips into your collection bin.
Bend the shaft of these retrievers to access hard to reach spaces and pick up objects using the claw or magnet.
An LED lights the wire jaws and the shaft bends to reach objects in awkward spaces.
The handle has a magnet at the end to pick up small steel objects. Use these picks to hold and position wire, springs, and other small parts.
The handles of these assorted picks have a magnet at the end to pick up small steel objects. Use to hold and position wire, springs, and other small parts.
Coated with PTFE, these stirring bars are corrosion and chemical resistant.
Fish stirring bars out of containers using the magnetic end of these retrievers.
The magnetic end of these standoffs makes it easy to temporarily mount or reposition components on magnetic surfaces.
Easily grab iron and steel fasteners, small sheets, and other parts from work areas, bins, and hard-to-reach places.
Pick up nuts, bolts, and other small parts with the magnet at the end of the mirror handle.
Switch between three mirrors, a magnifying lens, and two retrieval magnets depending on your inspection job.