The hex shape achieves the best possible grip on hex fasteners to prevent rounding their points.

These short sockets fit spaces where height clearance is limited.

Pivot the head to access fasteners from an angle.

With a plastic insert, these sockets firmly grip hex nuts and bolts without rounding them or scratching highly polished finishes.

Designed to fit on external Torx-Plus fasteners, often found on pickup trucks, these sockets have squared lobes that resist slipping at high torque.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet IEC 60900.

Grip the indentations around the outside of tri-groove fasteners.

Turn many sizes of square, hex, and 8-point fasteners with one socket. Place over the fastener and 54 pins move to grip it securely.

These sockets fit the nuts found on water and gas valves.

Make maximum contact with all sides of a fastener to reduce slipping. These sockets are also known as torque adapters.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet ASTM F1505 and IEC 60900.

Tighten and loosen fasteners at an angle by pivoting the head on these sockets.

When vertical space is tight or you need an extra twist on your socket, use these dual drive hex bit sockets. They work with a standard square drive tool and a box or open end wrench.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

These sockets are also known as pin-in-Torx bits.

The short Phillips bit on these sockets fits in spaces that screwdrivers can’t and where height clearance is limited.

An extra-long Phillips bit allows these sockets to reach far-away fasteners. Use them where standard or stubby sockets can’t reach.

An opening at the tip of these sockets fits around the security pin, allowing you to drive tamper-resistant Torx Plus screws.

Pivot the head to access fasteners from an angle.

A magnet holds the fastener securely enough to drive self-tapping screws.

With a smaller OD than standard sockets, these fit between tightly spaced fasteners.

Extra length allows access to fasteners on long bolts.

Quickly position these sockets on square fasteners.

Pivot the head to access fasteners from an angle.

The 12-point shape quickly positions on hex fasteners.

Use bit sockets as an alternative to a screwdriver or L-key.

Extend the shaft for additional length.

The L shape provides clearance when reaching over obstructions.

Fasten quickly with these crank-style handles.

Bend around obstructions to turn hard-to-reach fasteners.

Apply more torque than your wrench can deliver on its own. Use a multiplier with a torque wrench to ensure you do not exceed the maximum input torque.

Suitable for occasional maintenance work, these sets are imported.

Pivot the head to access fasteners from an angle.

With squared lobes that won’t slip at high torque, all of the sockets in these sets are designed to fit on external Torx-Plus fasteners, often found on pickup trucks.

Grip the indentations around the outside of tri-groove fasteners.

Access 6-point nuts and bolts in tight and awkward spaces—the heads on these sockets pivot.

Suitable for occasional maintenance work, these sets are imported.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

Extra-long bits allow access to hard-to-reach fasteners.

Extra-long bits allow access to hard-to-reach fasteners.

When vertical space is tight or you need an extra twist on your socket, use one of the dual-drive Phillips bit sockets in this set.

Often used with an extension, these sockets turn fasteners and fittings in obstructed areas that a regular socket can't reach. They are also known as crowfoot wrenches.

Use these sockets as an alternative to a screwdriver or L-key. They are made to withstand the high torque and force of impact tools.

Pivot the head to access fasteners from an angle.

The hex shape grips hex fasteners and prevents rounding. These sockets are made to withstand the high torque and force of impact tools.

Convert from one square drive size to another.

Convert from one square drive size to another.

Change a standard wrench handle into a ratcheting wrench.

Pivot the head to access fasteners from an angle.

Safely lengthen the reach of your socket while working near flammable vapors and combustible residue.

Safely extend your reach in areas where you could accidentally come into contact with live circuits.

Bend these socket extensions around obstructions to turn hard-to-reach fasteners.

Set a desired torque within the range.

Reach a variety of spots with the confidence that your extension won’t disengage.

Adapters are set to a specific torque and cannot be adjusted.

Fit these adapters between your wrench and socket to enable finger tightening.

Lock the adapter on your tool and the socket to the adapter to prevent accidental disengagement.

Convert from one square drive size to another.

Lock your socket into the extension to prevent accidental disengagement.

Prevent overtightening that can damage fasteners. These adapters spring back slightly when the set torque is reached.

Reach a variety of spots by keeping common extension lengths on hand.

First developed for aerospace and automotive assembly processes, these extensions will stand up to your high-volume production and assembly lines.

The slots in these low-profile organizers are a different color than the base so it's clear when tools are missing from your bench top or drawer.

The rail is smooth plastic so the clips move more easily than on steel-rail organizers.

Hold different square drive sizes on the four clip rails stored in these trays.

Using your ratchet wrench as a handle, access hard-to-reach caps and plugs or grip objects of almost any shape.