These wrenches are made of stainless steel for excellent corrosion resistance.

When working in tight spaces, these short wrenches fit where others can't.

Flip these wrenches over to ratchet in the opposite direction.

A lever reverses the ratchet direction.

A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

These wrenches are made of stainless steel for excellent corrosion resistance.

When working in tight spaces, these short wrenches fit where others can't.

Suitable for occasional maintenance work, these sets are imported.

Pivot the box end for access to fasteners in tight spots.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.

These wrenches are made of stainless steel for excellent corrosion resistance.

Made of aluminum-bronze that is Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

These are also known as tappet wrenches.

Sized for working on small equipment, these wrenches are 4 1/8" long with a slim head and handle.

When turning fasteners in small spaces, these short wrenches fit where others can't.

The head is offset 45° to provide additional clearance when reaching over obstructions.

Also known as alligator wrenches and water-meter nut wrenches, the V-shaped head fits multiple hex fastener sizes.

One head is angled 60° for access to hard-to-reach fasteners. These are also known as ignition wrenches.

Made of stainless steel, these wrenches have excellent corrosion resistance.

The slim heads fit into tight spaces and around thin fasteners.

Sized for working on small equipment, these wrenches are 4 1/8" long with a slim head and handle.

The opening shape makes more contact with fasteners for a better grip than standard open-end wrenches. These tools are also known as flare-nut or line wrenches.

Extend the shaft for additional length.

Position the head anywhere along the handle.

Turn sockets from above when there's not room to swing a standard wrench handle.

Fasten quickly with these crank-style handles.

Trust the precision of your measurements—these wrenches are accurate to ±1%.

Trust the precision of your measurements—these wrenches are accurate to ±2%.

Turn sockets from above when there's not room to swing a standard wrench handle.

Also known as impact drivers, use these tools with impact sockets to break frozen bolts and screws free. Strike with a hammer to tighten and loosen fasteners.

Built for durability, these high-performance tools handle the demands of high-volume production and tough maintenance applications.

Set torque and the wrench will prevent you from exceeding it. These are also known as nutrunners.

The handle is covered in plastic for a comfortable grip.

Press the lever to lock the jaw and keep these wrenches clamped on your work, leaving your hands free.

A plastic-covered handle provides a comfortable grip.

These tools have the heavy duty handle and adjustment mechanism of a pipe wrench and the smooth jaws of a traditional adjustable wrench.

Fit the thin head and long jaws into narrow spaces.

Also known as a basin wrench, this tool has a pivoting head and spring-close jaws for working in tight spaces where it’s difficult to adjust a traditional wrench.

Flip the wrench over to use the raised section on the head as a hammer.

Reverse the movable jaw to convert from a smooth-jaw adjustable wrench to a serrated-jaw pipe wrench.

The handles are covered in plastic for a comfortable grip.

The heads are angled to provide clearance around obstructions.

Also known as slugging wrenches, strike the handle with a hammer to break stuck fasteners free.

The head is offset 45° to provide clearance for reaching over obstructions.

The head is offset 45° to provide clearance for reaching over obstructions.

These wrenches are polished for a mirror-like finish.

Turn lug bolts on car and truck wheels. These wrenches have a different socket size at each end.

Pivot the socket end to access hard-to-reach fasteners.

These wrenches have one pivoting socket end and one open end.

Open and close the jaws with one hand. Press the lever and slide the bottom jaw to the desired position; tension keeps it in place.

Made of materials that are Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant.

The jaws grip most round surfaces, even highly polished objects. Push down on the wrench and pull the handle toward you—the jaws will tighten around the workpiece.

Use one end as a traditional pipe wrench and the other to loosen valve wheels. These are also known as engineers’ pipe wrenches.

Turn the end of the handle to set torque, and the wrench makes an audible click when it reaches the setting.