When working in tight spaces, these short wrenches fit where others can't.

Flip these wrenches over to ratchet in the opposite direction.

A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.

Flip these wrenches over to ratchet in the opposite direction.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Flip these wrenches over to ratchet in the opposite direction.

Suitable for occasional maintenance work, these sets are imported.

A lever reverses the ratchet direction.

One head is angled 60° for access to hard-to-reach fasteners. These are also known as ignition wrenches.

These are also known as tappet wrenches.

The opening shape makes more contact with fasteners for a better grip than standard open-end wrenches. These tools are also known as flare-nut or line wrenches.

Fit the narrow head into tight spaces and around thin fasteners.

One head is angled 75° for access to hard-to-reach fasteners. These are also known as ignition wrenches.

The opening shape makes more contact with fasteners for a better grip than standard open-end wrenches. These tools are also known as flare-nut or line wrenches.

The handle is covered in rubber for a comfortable grip.

A gasket seals in permanent lubrication and keeps out dirt, dust, and moisture.

Twist the grip to rapidly turn a socket before final tightening or to remove a fastener once loosened. The handle also swings like a traditional ratchet wrench.

Pair these wrenches with a bolt-through socket to reach nuts at the bottom of a long threaded rod or bolt which can pass through the head of the wrench.

The 20° offset head provides clearance when reaching over obstructions.

Rather than teeth, these wrenches use a series of rollers to engage the ratchet, enabling work in the tightest of spaces. Also known as silent ratchets, they don't make the traditional click sound when turned.

Extend the shaft for additional length.

Position the head anywhere along the handle.

The ratcheting mechanism turns sockets quickly.

Pivot the head to access fasteners in tight spots.

Unlike most torque wrenches, you don’t have to return the torque setting to the lowest value after use. These tools are also known as split-beam torque wrenches.

Trust the precision of your measurements—these wrenches are accurate to ±1%.

The most advanced torque wrenches we offer, these tools store and recall up to 1,500 torque and angle measurements.

Trust the precision of your measurements—these wrenches are accurate to ±2%.

These wrenches slip to disengage and stop turning the fastener when the set torque is reached, preventing overtightening.

When the set torque is reached, these wrenches signal with an audible click and an impulse in the grip.

Grip more of your fastener head with these wrench heads.

These short sockets fit spaces where height clearance is limited.

Pivot the head to access fasteners from an angle.

Slide the open side of these sockets over a tube or hose to adjust a nut that’s already installed.

Pair these sockets with a bolt-through ratchet wrench to reach nuts at the bottom of a long threaded rod or bolt which can pass through the socket and the head of the wrench.

Pivot the head to access fasteners from an angle.

Also known as pipe plug sockets, these sockets have a square shape that provides the best possible grip on square fasteners and prevents rounding.

Slip these slotted sockets onto wing nuts to tighten or loosen them with more force than fingers can apply.

The short bit on these sockets fits in spaces where height clearance is limited.

Tighten and loosen fasteners at an angle by pivoting the head on these sockets.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

Extra-long bits allow access to hard-to-reach fasteners.

The short Phillips bit on these sockets fits in spaces that screwdrivers can’t and where height clearance is limited.

An extra-long Phillips bit allows these sockets to reach far-away fasteners. Use them where standard or stubby sockets can’t reach.

These sockets are also known as Robertson bits.

An opening at the tip of these sockets fits around the security pin, allowing you to drive tamper-resistant Torx Plus screws.

Pivot the head to access fasteners from an angle.

Suitable for occasional maintenance work, these sets are imported.

Access 6-point nuts and bolts in tight and awkward spaces—the heads on these sockets pivot.

Two spring-loaded balls inside these sockets firmly hold nuts and bolts in place as you turn them, including nonmagnetic fasteners like stainless steel screws.

Suitable for occasional maintenance work, these sets are imported.

Shaped and sized for compatibility with wheel bearing locknuts on trucks and trailers, the sockets in these sets make it easy to install and remove locknuts.

Attach one of the heads in these sets to a torque wrench for more leverage to loosen a stubborn fastener.

Connect one of the heads in these sets to a socket extension to reach an obstructed fastener, then turn the fastener without removing and repositioning the wrench head.

The short bit on these sockets fits in spaces where height clearance is limited.

A spring-loaded ball on the bit holds fasteners in place as you drive them, including nonmagnetic fasteners like stainless steel screws.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

These sockets are also known as pin-in-Torx bits.

Pivot the head to access fasteners from an angle.

Keep common extension lengths on hand to reach a variety of spots—just attach them to your socket.

Tighten and loosen fasteners in hard-to-reach spots with a variety of extensions that lengthen the reach of your socket.

The male ends of these extensions are rounded, so they can pivot to use your tool at an angle.

Lock your socket into these extensions to prevent accidental disengagement.

Push the square drive through the adapter to change size.

Convert your socket into a flex socket to access fasteners from an angle.

Convert your socket into a flex socket without worrying about the adapter falling off.

A digital display shows how torque measurements change as you turn the wrench. Set the desired torque and angle—lights and an audible alarm indicate when target has been reached or exceeded.

The handle is covered in plastic for a comfortable grip.

Press the lever to lock the jaw and keep these wrenches clamped on your work, leaving your hands free.

Turn fasteners with the firm grip of a wrench and the adjustability of pliers.

A ratchet mechanism in the head allows you to turn fasteners in tight spaces without removing and repositioning the wrench.

The heads are angled to provide clearance around obstructions.

Ratchet mechanisms allow you to turn fasteners in tight spaces without removing and repositioning the tool.

An insulated handle protects against accidental contact with live electrical circuits. These wrenches are tested to 1,000 volts to meet IEC 60900.

The offset head gives you additional clearance to turn hard-to-reach fasteners.

These wrenches are polished for a mirror-like finish.

A ratchet mechanism allows you to turn fasteners in tight spaces without removing and repositioning the wrench.

Turn nuts on bolts and threaded rods, which can pass through the short end of the wrench. For additional leverage, slip a bar through the short end to create a T-handle.