Made of PVC, this sleeving resists chemicals, oil, and acids.

Add a layer of insulation to prevent electricity and heat from dissipating from wire and cable.

Made from thicker and denser fiberglass than standard spark-resistant sleeving, this sleeving is more abrasion resistant and provides better insulation. The silicone rubber coating protects against sparks and molten metal splash.

Tight braiding makes this sleeving resistant to fraying when cut with scissors. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Protect cable, hose, and pipe in high temperature environments—this sleeving withstands temperatures over 450° F. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Reduce the likelihood of slipping in high-traffic areas. This sleeving has thick, nonslip fibers that create friction so it doesn’t slide when you step on it. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Rated UL 2024 and NFPA 262, this sleeving is approved for use in plenum spaces such as duct work and above a drop ceiling. It self-extinguishes and emits minimal amounts of smoke and gas during combustion. Stretch to fit over items for easy installation; it tightens around its contents for a secure fit.

Unlike fiberglass and silica, this sleeving won't irritate skin, so it's easier to handle. It has a temperature rating of 1100° F or higher.

A blend of Aramid and fiberglass gives this sleeving excellent abrasion resistance. It can withstand temperatures up to 650° F

Tightly braided nylon fibers give this sleeving excellent abrasion resistance. As it wears, the fibers frizz and make the outer wall thicker for improved protection.

Made of nylon, this sleeving is the most impact- and abrasion-resistant slit corrugated sleeving we offer. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them.

Rated UL 94 V-2, this sleeving resists combustion and minimizes the spread of flames. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them. It has impact and abrasion resistance similar to conduit, with more flexibility.

This sleeving reflects heat away from contents and withstands temperatures up to 900°F. The corrugated construction gives it impact and abrasion resistance similar to conduit, but with more flexibility.

A hinge along the entire length makes this one-piece sleeving easy to open for installation. Interlocking ridges overlap along the opening to protect contents from dust and dirt. The corrugated construction gives it the impact and abrasion resistance of conduit, with more flexibility.

Zip this sleeving around wire, cable, or hose that are connected at both ends to quickly bundle them.

A strip of hook-and-loop creates a strong seal along the entire length of this sleeving, yet it can be opened at any point to access contents. Use it to wrap around wire, cable, or hose without disconnecting them.

The tightly braided construction makes this polyester sleeving abrasion resistant. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.

Often used to protect wire, cable, and hose in robotics and other automated applications, this highly flexible sleeving withstands continuous motion without tearing or fraying.

Made of aluminum with a fiberglass liner, this sleeving reflects heat away from contents and withstands temperatures up to 390°F. A slit along the entire length makes it easy to install around wire, cable, and hose without disconnecting them.

Silicone rubber coats this fiberglass sleeving to shed sparks and molten metal splash. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.

Made of PTFE, this sleeving has excellent resistance to chemicals and acids. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

Made with a self-extinguishing additive, this sleeving will not produce fumes when exposed to open flame or high temperatures. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

A mica and silicone rubber blend allows this sleeving to withstand temperatures up to 2100° F. It can be quickly applied to hose or cable like tape, so it's a good option for emergency patches.

Create a water-resistant seal—this tubing has an adhesive lining that melts when the tubing is heated and bonds to the underlying surface.

This PTFE tubing withstands temperatures up to 450° F and has an inner lining that creates a water-resistant seal when heated.

Use this tubing where wire and cable may be exposed to chemicals, oil, and acids.

Resistant to diesel fuel, hydraulic fluid, and lubricating oil, this tubing is often used in vehicles.

Use this general purpose tubing to insulate and protect wire and cable.

Identify ground wire with this green-and-yellow striped tubing.

This tubing creates a tight seal over irregularly shaped objects.

A layer of conductive cloth protects wire and cable from signal interference caused by nearby equipment and devices.

After being cleaned with alcohol, this tubing is bagged and sealed in a clean room. It's certified for material quality and purity.

Use this tubing in applications where temperatures reach up to 500° F. It's often used to insulate electronic components.

This tubing shrinks down to a quarter of its original ID, so it creates a tight seal over irregularly shaped objects. It withstands up to 500° F.

Made of woven polyolefin/polyester fabric, this tubing has excellent abrasion resistance so it can be dragged over rough surfaces without damage.

Keep general purpose tubing in a variety of sizes on hand.

A different shrink ratio on each end allows this tubing to fit over cable assemblies and wire harnesses with large connections, or around connectors with a 90° elbow.

Organize and route wire and cable in an enclosure—this tubing bundles wires together while allowing them to reach different connection points.

Protect wire and cable without disconnecting them from an assembly. For a water-resistant seal, this wrap has an adhesive lining that melts when the tubing is heated and bonds to the underlying surface.

Use this wrap with heat-shrink tubing to create a moisture-resistant seal. Apply it like tape around wire and cable, then slide the tubing over the wrap. The wrap melts when tubing is heated and bonds to the underlying surface.

Thicker corrugations make this conduit more crush resistant than standard flexible plastic conduit.

Protect fiber optic cable with this small-diameter conduit.

Even in temperatures as low as -50° F and as high as 220° F, this conduit stays flexible.

In addition to resisting oil, this conduit resists lubricants and grease.

Run conduit in food areas—the cover can be cleaned and sterilized without weakening or splitting. This conduit meets NSF/ANSI standard 169 for special-purpose food equipment.

Also known as Type B, this conduit is more crush and abrasion resistant than liquid-tight flexible plastic conduit.

In addition to continuous-motion applications such as robotics, this conduit is suitable for high-vibration applications.

Use in food-processing and chemical plants—this is the most corrosion resistant thick-wall conduit we offer.

This nonmagnetic aluminum conduit withstands damp and corrosive environments.

This impact- and crush-resistant conduit is also known as galvanized rigid conduit (GRC).

Also known as intermediate metallic conduit (IMC), this is lighter in weight than thick-wall (rigid) steel conduit, yet it has the same strength.

Join pieces of conduit.

Join pieces of conduit.

Join pieces of conduit.

Often used as an alternative to cable ties, wire duct guides and organizes short runs of electrical wiring in enclosures, control panels, and machines.

Route wire and cable around curves with this bendable wire duct.

These cable ramps are strong enough to withstand equipment traffic.

Protect cable from carts, pedestrians, and other light indoor traffic.

These cable ramps handle heavy pedestrian and equipment traffic.

Use in areas with light pedestrian traffic.

Gaskets on the covers and at connection points protect against dust as well as seeping oil and coolant.

With more than one channel, this raceway allows you to separate power and data wiring to prevent signal interference.

With a top that overhangs the cover, this raceway keeps out rain. It is rated NEMA 3R for protection from liquids and light splashing.

Insert and remove cable at any point along the length of this open-top, hook-shaped raceway.

The triangular shape fits into corners.

Protect the cables on your TIG guns from weld spatter.