Extend your reach in hard-to-access areas—turn these valves on and off using a square ratchet to grasp the hole at the end of the handle. Use with water, oil, air, and inert gas.

An easy-to-read flow-indicating handle shows the percentage the valve is open. These valves are for use with water, oil, inert gas, and steam.

These valves are rated for at least three times the pressure of standard threaded valves. Use with water, oil, air, inert gas, and steam.

For fast installation and removal from pipelines, these valves have a union fitting that disassembles into multiple pieces. They’re for use with water, oil, air, inert gas, and steam.

Use these valves with water, air, and inert gas.

Bolt these valves to ANSI flanges. They’re for use with water, oil, air, inert gas, and steam.

Attach these valves to industry-standard two-bolt flanges on circulation pumps from manufacturers such as Bell and Gossett, Taco, Grundfos, and Armstrong. Use with water, air, and steam.

Clean and maintain these valves without removing welded connections. They have a three-piece bolted body that disassembles inline for easy access to internal components. Use with water, oil, air, inert gas, and steam.

Weld these valves to unthreaded metal pipe for a permanent, flush connection that permits smooth flow through a line. Use with water, oil, inert gas, and steam.

For fast installation and removal from pipelines, these valves have union fittings that disassemble into multiple pieces. Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves meet NSF/ANSI 61 for use in drinking water lines.

Disassemble the union fittings on these valves for fast installation and removal from your pipeline. All meet NSF/ANSI 61 for use with drinking water.

The most chemical-resistant threaded valves we offer, these have a PTFE seal and an alloy body that can withstand extremely aggressive and corrosive chemicals, such as methyl ethyl ketone and toluene.

The three-piece bolted body comes apart for access to internal components without unthreading pipe connections and removing the valve from your line. Seal is fluoroelastomer and body is polypropylene for excellent resistance to aggressive and corrosive solutions in chemical-processing applications.

Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves have a fluoroelastomer seal and a plastic body that can withstand aggressive and corrosive solutions in chemical-processing applications.

Install these low-profile valves in low-clearance pipelines for natural gas, propane, and butane.

Designed for use in refineries and other demanding environments, these durable valves have a forged steel body that can withstand at least twice the pressure of other threaded valves.

Insert unthreaded pipe into the socket ends and weld to create a permanent, leak-tight connection.

For use with threaded pipe, these valves have NPT connections.

These valves have NPT connections for use with threaded pipe.

The three-piece bolted body comes apart for access to internal components without unthreading pipe connections and removing the valve from your line.

A compact, lightweight actuator and an angular body allow you to install these valves in any mounting orientation.

Less than half the height of standard severe-duty valves, these fit in small spaces and low-clearance pipelines.

Also known as piston valves, these have a compact, lightweight actuator that allows them to be installed in any mounting orientation. They’re often used in water-treatment applications.

These top-of-the-line valves are comparable to Asco Red Hat 8210G Series and Parker Gold Ring 23C Series.

Turn the knob to adjust how much these valves will open or close when actuated. They are often used in irrigation and landscaping applications.

Designed to withstand the high temperatures and pressures in steam service applications.

Use with coolant and detergent such as ethylene glycol or soap solutions.

Sturdy internal components resist wear for a long service life in applications with frequent cycling.

With a plastic body and a fluoroelastomer seal, these valves can stand up to aggressive and corrosive solutions in chemical-processing applications.

Maintain and repair these valves without unthreading pipe connections. They have a three-piece bolted body that disassembles inline for access to internal components.

Separate the union fittings on each end of these valves for fast installation and removal from pipelines.

Insert unthreaded pipe into the socket ends and bond with PVC primer and cement to create a permanent, leak-tight connection.

Use these valves for boiler maintenance and other low-pressure plumbing applications. They're for use with water. All gradually open and close to adjust and regulate flow.

Rated for twice the pressure of other threaded flow-adjustment valves, these are often used in refineries and other demanding environments. Use with water, oil, air, and inert gas. They gradually open and close to adjust and regulate flow.

Insert unthreaded pipe into the socket ends and weld to create a permanent, leak-tight connection. These valves are for use with water, oil, air, inert gas, and steam. They gradually open and close to adjust and regulate flow.

Designed to withstand the extreme cold of liquid argon, liquid carbon dioxide, and liquid nitrogen, these valves are cleaned and bagged to meet CGA G-4.1 standards for oxygen service. They gradually open and close to adjust and regulate flow.

Often used in hydraulic and compressed air systems, these valves can withstand at least 6,000 psi. They’re for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Rated for nearly twice the maximum temperature of standard threaded precision flow-adjustment valves, these can handle up to 700° F. They’re for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Also known as proportional V-ball valves, these have a motor that adjusts and regulates flow in applications with higher flow rates and pressures than solenoid valves. As you increase the intensity of the electrical signal, the motor opens the valve, moving a ball with a V-cut opening that proportionately allows more flow as the valve opens. They're often integrated into PLC systems for automatic control over the valve position based on system conditions.

For faster actuation than motor-driven valves, these operate on compressed air. Integrate them into PLC systems for automatic control over the valve position based on system conditions. The actuator has a built-in electric pilot valve that controls the air supply to the valve. Set how much to open the valve using the programmable controller on the actuator.

Control flow in two directions from a single source—these valves have two handles for independent operation of each outlet. Use them with water, oil, and inert gas.

Perform valve maintenance without unthreading pipe connections. These valves have a three-piece bolted body that comes apart for inline access to internal components. The fluoroelastomer seal and glass-filled polypropylene body can withstand aggressive and corrosive solutions for diverting flow in chemical-processing applications.

To divert flow between ports in drinking water lines, these valves meet NSF/ANSI 61.

For use with threaded pipe, these valves have NPT connections. Use them with water, oil, air, and inert gas. All operate on compressed air to automatically divert flow between ports more quickly than motor-driven valves. You must control the air to the actuator using either an electric pilot valve or a manual on/off valve.

Automatically or manually start and stop flow in your line with these valve bodies, which attach to your actuator.

Attach these valve bodies to your actuator to automatically or manually control flow in your line.

To achieve the maximum possible flow, internal components are designed to reduce flow resistance.

Rated for up to twice the pressure of standard check valves, these can withstand pressures up to 3,000 psi.

Less than half the end-to-end length of standard flange-mount check valves, these can be installed in pipelines with limited clearance.

For more durability than plastic barbed check valves, these have a stainless steel body.

Weld to unthreaded metal pipe.

To reduce installation time and allow for maintenance without detaching pipe connections, these valves insert into a union fitting.

Bolt to ANSI flanges.

Body is plastic.

These heavy duty valves can withstand pressures up to 1,975 psi and temperatures up to 800° F.

Insert unthreaded pipe into the socket ends and weld to create a permanent, leak-tight connection.

Rated for 12 times the pressure of standard vacuum-breaking valves, these can handle up to 1,500 psi. Connections are NPT.

Measure, throttle, and regulate the flow of liquids and gases in your line by adding an orifice plate to these unions.

To minimize fluid loss when connecting and disconnecting your line, these couplings have flat faces for a close fit and shut-off valves to stop the flow—they meet ISO 16028, which is an international standard for hose couplings.

Use these couplings at pressures up to 5,000 psi. They consist of a plug and socket that connect and disconnect quickly. Use them if you need frequent access to a line. They are compatible with International Standard ISO B-shape plugs and sockets.

Use these couplings at pressures up to 10,000 psi. Also known as flush-face couplings, the plugs and sockets have a flat face, which allows them to mate close together, reducing fluid loss when connecting and disconnecting the line. They are compatible with High-Pressure Minimal-Spill-shape plugs and sockets.

Use these couplings at pressures up to 3,000 psi. They consist of a plug and socket that connect and disconnect quickly. Use them if you need frequent access to a line. They are compatible with Pioneer-shape plugs and sockets.

Made of brass with a steel wing nut, these couplings are tough enough to handle occasional drops to concrete and frequent connections on dump truck, oil rigs, and other heavy duty equipment. Compared to push-to-connect couplings, these are threaded, so they're easier to connect when there's pressure in your line.

Use these couplings when you need frequent access to a gas line. A complete coupling consists of a plug and a socket that connect and disconnect quickly.

These couplings are compatible with International Standard ISO Series B-shape plugs and sockets. They are FDA compliant, so they’re suitable for food and beverage applications and won’t impart tastes or odors to the product. They consist of a plug and a socket that connect and disconnect quickly so you can frequently access your line. Use at pressures up to 220 psi.

There’s no shut-off valve on these nozzles, so water instantly flows.

Dispense and control the flow of coolant with these nozzles.

Unlike other manifolds, which have an inlet on either end, these have one inlet on the opposite side from the outlets. This design allows air or fluid to follow a straight path, improving flow through your system. Also known as headers.

When you’re short on vertical space, these manifolds are a good fit—they have outlets on the side instead of on top, so they have a lower profile than rectangular manifolds. Use them to distribute air or fluid to five locations from a single supply source.

Use these manifolds with molding equipment to circulate hot and cold water through your line. They have a red side for hot water and a blue side for cold water.

Set your flow rate and then adjust it as necessary; these valves maintain flow rate despite pressure changes in the system.

Lock the handle using a padlock.

Nearly half the height of our other remote-reading temperature-regulating valves, these are often used in low-clearance areas.