Manually control these valves by pushing or turning the actuator. Also known as 3-way or 3/2 valves, they create one action, such as extending a cylinder. They direct airflow from the inlet to your equipment and exhaust return airflow to create motion. In the off position, they exhaust air pressure from the system, allowing equipment to reset so the action can be repeated.

Normally closed valves block airflow until actuated. Valves that are both normally closed and normally open can be installed to block airflow, or allow air to flow until actuated.

Valves with hand return actuation stay actuated and go back to their starting position only when you move the actuator again. Valves with spring return actuation go back to their starting position as soon as you release the actuator.

Flow coefficient (Cv) is a measurement that indicates how much airflow can pass through a valve. When selecting between valves with the same port size, choose the valve with the higher flow coefficient to ensure it provides enough airflow to operate your system.

For technical drawings and 3-D models, click on a part number.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/2 valves, they actuate when voltage is applied to the electrical connection. They direct airflow from the inlet to your equipment and exhaust return airflow to create motion.

Valves with spring return actuation go back to their original position when voltage is removed.

Flow coefficient (Cv) is a measurement that indicates how much airflow can pass through a valve. When selecting between valves with the same port size, choose the valve with the higher flow coefficient to ensure it provides enough airflow to operate your system.

For technical drawings and 3-D models, click on a part number.

Run through equipment cycles up to 30% faster than with standard valves. These valves shift between flow positions in 1.7 ms. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/2 valves, they actuate when voltage is applied to the electrical connection. They direct airflow from the inlet to your equipment and exhaust return airflow to create motion. Return actuation is by spring, so they go back to their starting position as soon as voltage is removed.

Flow coefficient (Cv) is a measurement that indicates how much airflow can pass through a valve.

Run through equipment cycles up to 30% faster than with standard valves. They create one action, such as extending a cylinder. Apply voltage to the electrical connection to actuate. They direct airflow from the inlet to your equipment and exhaust return airflow to create motion. Return actuation is by spring, so they go back to their starting position as soon as voltage is removed. Also known as 3-way and 3/2 valves.

Normally open valves allow airflow until actuated. Normally closed valves block airflow until actuated.

Mufflers (sold separately) reduce exhaust noise.

Flow coefficient (Cv) is a measurement that indicates how much airflow can pass through a valve.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as pilot valves and 4-way valves, they use an air signal to actuate, so they're good for environments where electrical use may be dangerous. They direct airflow from the inlet to your equipment and exhaust return airflow to create motion.

Those with air-assisted spring return actuation require you to supply air to port P to go back to their starting position.

Valves with air pilot return actuation go back to their starting position when the air supply is moved from the first air pilot to the second air pilot.

Flow coefficient (Cv) is a measurement that indicates how much airflow can pass through a valve.

For technical drawings and 3-D models, click on a part number.

A simple automation solution that requires no programming, these valves are activated when an object, such as a box rolling on a conveyor, pushes the actuator. Also known as 3-way and 3/2 valves, they create one action, such as extending a cylinder. Valves direct airflow from the inlet to your equipment and exhaust return airflow to create motion. Return actuation is by spring, so they go back to their starting position as soon as the actuator is released. In the off position, they exhaust air pressure from the system, allowing equipment to reset so the action can be repeated.

Valves that are both normally closed and normally open can be installed to block airflow, or allow air to flow until actuated.

Valves with a one-direction actuator are activated by objects from one side.

Valves with a two-direction actuator are activated by objects from both sides.

Flow coefficient (Cv) is a measurement that indicates how much airflow can pass through a valve. When selecting between valves with the same port size, choose the valve with the higher flow coefficient to ensure it provides enough airflow to operate your system.

For technical drawings and 3-D models, click on a part number.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Operate them with your foot, leaving your hands free to perform other tasks. Valves direct airflow from the inlet to your equipment and exhaust return airflow to create motion. The foot guard prevents accidental valve operation. Also known as 4-way and 5/2 valves.

Valves with spring return actuation go back to their original position as soon as you release the actuator.

Valves with a foot return actuation stay actuated and go back to their original position only when you step on them again.

Flow coefficient (Cv) is a measurement that indicates how much airflow can pass through a valve.

For technical drawings and 3-D models, click on a part number.

Mount valves to a single-station base or to a manifold, which allows a single pressure source for multiple valves, then add or remove valves as your needs change. Valves with the same style can be used on the same manifold. For example, you can put a Style B, 2-position, spring-return valve and a Style B, 3-position, solenoid-return valve on the same manifold.

4-way valves create two actions, such as extending and retracting a double-acting cylinder.

5/3 (closed center) valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. 5/3 (exhaust center) valves exhaust all air pressure in the off position, allowing equipment to return to the neutral position. 5/3 (pressure center) valves create two actions at the same time, such as extending two single-acting cylinders at once.

Valves with spring return actuation go back to their original position when voltage is removed. Valves with electric (solenoid) return actuation go back to their original position when voltage moves from the first solenoid to the second solenoid.

Station plates cover unused manifold ports.

Flow coefficient (Cv) is a measurement that indicates how much airflow can pass through a valve.

Meter out valves control flow as it exits the cylinder. Meter in valves control flow as it enters the cylinder.

For technical drawings and 3-D models, click on a part number.

Prevent damage to your equipment by limiting startup airflow and then gradually raising the airflow rate to operating levels. These valves adjust the volume of air exiting an air cylinder (meter out) to control the speed of air-powered equipment. They control flow in one direction; air flows freely in the opposite direction. For the best control, mount them as close to the cylinder as possible to minimize the length of tubing between the cylinder and the valve.

Flow coefficient (Cv) is a measurement that indicates how much airflow can pass through a valve.

For technical drawings and 3-D models, click on a part number.

Also known as blocking valves, these valves are activated by an air signal to turn equipment on and off. They allow airflow when an air signal is applied to the air pilot. When the air supply is removed, the valve closes, trapping air in the system.

Valves with push-to-connect ports are for use with plastic or soft metal tubing. Insert tubing into the port.

Flow coefficient (Cv) is a measurement that indicates how much airflow can pass through a valve. When selecting between valves with the same port size, choose the valve with the higher flow coefficient to ensure it provides enough airflow to operate your system.

For technical drawings and 3-D models, click on a part number.

The 90° elbow shape allows you to install these valves in tight spaces. They quickly vent exhaust air to the atmosphere or divert it to another place in your system to speed up the movement of air cylinders. Also known as quick exhaust valves.

NPTF (Dryseal) threads are compatible with NPT threads.

Flow coefficient (Cv) is a measurement that indicates how much airflow can pass through a valve. When selecting between valves with the same port size, choose the valve with the higher flow coefficient to ensure it provides enough airflow to operate your system.

For technical drawings and 3-D models, click on a part number.