These valves have 37° flared tube fittings that form a tight seal on metal tubing lines to transfer diesel fuel, fuel oil, and gasoline.

Install these valves in gas pipelines to automatically control the flow of natural gas, propane, and butane to equipment.

An aluminum body provides strength and durability at half the weight of other metal flanged flow-adjustment valves. These valves are for use with water, oil, air, and inert gas. They bolt to flanges to adjust and regulate flow in flanged pipelines.

To prevent flashback in flammable gas pipelines, an internal flame-arresting element absorbs the heat from a fire to extinguish the flame.

Made of nickel-plated brass, these fittings have better corrosion resistance than unplated brass fittings.

Use these valves in pipelines.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/2 valves.

These valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. They create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/3 closed center valves.

Control these valves with one hand. Also known as 4/2 valves, they create two actions, such as extending and then retracting a double-acting cylinder.

In the off position, these valves exhaust all air pressure, allowing the equipment to return to the neutral position. Also known as 4/3 exhaust-center valves, they create two actions, such as extracting and then retracting a double-acting cylinder.

Control six different outputs from a single source of airflow. These valves have one inlet port and six outlet ports. Push in and rotate the dial to move between outlet ports and send airflow to a different output.

Because they require a key to operate, you can limit who is able to adjust these valves. They create one action, such as extending a cylinder.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 5/2 valves, they actuate when voltage is applied to the electrical connection.

These valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Apply voltage to the electrical connection to actuate.

Also known as 4-way and 5/2 valves, these valves create two actions, such as extending and then retracting a double-acting cylinder. Apply voltage to the electrical connection to actuate.

Also known as 3/3 valves, these valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. They're often used for vacuum suction and release applications and intermediate cylinder stops.

Ceramic plates form a longer-lasting seal against oil and dust than rubber seals that deteriorate over time. These valves withstand use in corrosive, dusty, and dirty environments such as foundries, paper mills, and steel plants. Apply voltage to the electrical connection to actuate.

Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as pilot valves and 4-way valves, they use an air signal to actuate, so they're good for environments where electrical use may be dangerous.

These valves create one action, such as extending a cylinder. Also known as 3/2 or pilot valves, they use an air signal to actuate, so they're good for environments where electrical use may be dangerous.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. They activate when an object, such as a box rolling on a conveyor, pushes the actuator. Also known as 4-way and 5/2 valves.

Mix and match valve styles on one manifold to meet your control needs. Mount multiple valves to a manifold to reduce piping requirements and create multiple actions from a single pressure input.

Designed to be mounted inline, these valves can be installed in an easy-to-reach location along your line. They control the speed of air-powered equipment by adjusting the volume of airflow.

Adjust airflow equally in both directions. These valves regulate the speed of airflow as it enters and exits equipment. They're often used to control the extension and retraction speed of an air cylinder at the same time.

A padlock locks the handle of these valves in the shut-off position so you can disconnect air tools safely.

Quickly vent exhaust air to the atmosphere or divert it to another place in your system to speed up the movement of equipment. The 90° elbow shape allows you to install them in tight spaces. Also known as quick exhaust valves.

Designed for use in dust-collection systems, these diaphragm valves periodically burst air to knock debris from filters.

Control flow with an electrical signal.

Control the direction of flow or stop flow altogether.

Set a specific pressure and these valves will maintain it.