Connect high-pressure brake lines with fittings that won’t crack in frigid temperatures. Often used on commercial trucks and trailers, these fittings meet Department of Transportation FMVSS 571 safety standards.

Tube supports slip inside tubing to prevent the walls from collapsing.

Use these sleeves with brass compression nuts and fittings to create a seal on plastic and rubber tubing.

Use these nuts with plastic compression fittings to create a seal on plastic tubing. They're moisture-resistant acetal, so they won't absorb water and soften, even in high-humidity environments.

Use these nuts with plastic compression fittings to create a seal on plastic tubing. They have a built-in sleeve (ferrule), so the sleeve is positioned correctly for installation.

Connect these fittings to tubing with a ring and a crimping tool (both sold separately). Safe to use with drinking water, these fittings meet the strict standards of NSF/ANSI 61.

Use these fittings at pressures up to 9,700 psi. Also known as instrumentation fittings, they are made to tight tolerances for use in high-precision applications. They are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on stainless steel tubing that is flared to 37°.

The male pipe threads on these fittings have a sealant applied for extra protection against leaks.

The threads on the tube end of these fittings are Class 3A or 3B and adhere to tighter tolerances than other 37° flared fittings.

A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal. The nut and sleeve are included.

Use these sleeves with compression nuts and fittings to create a strong seal on stainless steel tubing.

The smooth finish inside these stainless steel quick-clamp fittings makes it easy to remove product residue.

Solder these fittings to tubing for a permanent, leak-tight connection. They are also known as sweat fittings.

Use these temporary flow stops to block water from an area that's being soldered. Commonly used on copper tubing, they allow you to make repairs without waiting for your line to drain.

No sleeve is required to assemble these fittings, which makes for a faster, more convenient installation compared to 37° flared fittings. They are also known as refrigeration and SAE fittings.

Also known as JIC (Joint Industrial Council) fittings, these connect to tubing that is flared to 37°. They can handle higher pressures than 45° flared fittings.

Made of plastic, these fittings are lightweight compared to our brass push-to-connect fittings.

Create a leak-tight seal without using heat or solder. Slide copper tubing into a press-connect fitting and use these tools to crimp the connection.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on steel tubing that is flared to 37°.

Use these sleeves with a nut and fitting to provide a tight metal-to-metal seal on steel tubing that is flared to 37°.

These fittings have two sleeves for extra gripping power. They bite into steel tubing as you tighten the nut to form a strong seal.

Use these nuts with compression sleeves and fittings, also known as bite fittings, to create a strong seal on steel tubing.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight seal on tubing that is flared to 37°.

Fittings are metal for better durability than plastic barbed hose fittings. They have sharper barbs than standard barbed hose fittings to grip push-on hose without the need for clamps or ferrules. The more you pull on the fittings, the tighter the hose will grip.

Fittings have sharp barbs that grip push-on hose with no clamps or ferrules required. The more you pull on the fittings, the tighter the hose will grip. Use in low-pressure hydraulic applications up to 350 psi.

Solder these valves to copper tubing for a permanent, leak-tight connection.

For a leak-tight connection, crimp the press-connect fittings on these valves to metal tubing with a crimping tool—no heat or soldering required. They open and close gradually as the wheel handle turns, preventing sudden starts and stops of flow.

For more durability than plastic valves, these are made of metal. A compression sleeve bites into tubing as you tighten the nut, forming a strong seal. Use these valves with water, oil, air, inert gas, and steam.

Solder these valves to metal tubing for a permanent, leak-tight connection. Use with water, oil, air, inert gas, and steam.

Solder these valves to metal tubing for a permanent, leak-tight connection. They meet NSF/ANSI 61 for use with drinking water.