How to Identify and Measure Fittings
Pipe size is an industry designation, not the actual size. View information about how to measure threaded and unthreaded pipe and pipe fittings.
More
How to Measure Threaded Pipe Size
More
Nickel-Plated Brass Push-to-Connect Tube Fittings for Air


(SAE Straight) Male
Threads with Gasket
- For Use With: Air, Lubricated Air
- Temperature Range: 0° to 140° F
- Tubing: Fittings with Release Ring and Fittings with no Release Type: Use with firm or hard (Durometer 95A-60D) nylon plastic, polyethylene plastic or polyurethane rubber
Fittings with Release Sleeve: Use with firm or hard (Durometer 95A-60D) polyethylene plastic or polyurethane rubber
Made of nickel-plated brass, these fittings have better corrosion resistance than unplated brass fittings. Also known as instant fittings, they connect to tubing with a push, and an internal gripping ring and O-ring hold the tubing tight. To disconnect, push on the release ring or sleeve and pull the tubing out of the fitting.
Fittings with release sleeve are easier to disconnect than fittings with a release ring because they are seamless and won't collect dirt and debris.
Metric and UN/UNF (SAE Straight) male threads with gasket or thread sealant provide extra protection against leaks.
For technical drawings and 3-D models, click on a part number.


(SAE Straight) Male
Threads with Gasket
Release Sleeve | |||||||
---|---|---|---|---|---|---|---|
For Tube OD | Thread Size | Thread Pitch, mm | Material | Gasket Material | Max. Pressure | Each | |
Metric Threads | |||||||
1/8" | M8 | 1 | Nickel-Plated Brass | Buna-N Rubber | 230 psi @ 72° F | 00000000 | 000000 |
1/4" | M8 | 1 | Nickel-Plated Brass | Buna-N Rubber | 230 psi @ 72° F | 00000000 | 00000 |
3/8" | M8 | 1 | Nickel-Plated Brass | Buna-N Rubber | 230 psi @ 72° F | 00000000 | 00000 |
4mm | M8 | 1 | Nickel-Plated Brass | Buna-N Rubber | 230 psi @ 72° F | 00000000 | 00000 |
6mm | M8 | 1 | Nickel-Plated Brass | Buna-N Rubber | 230 psi @ 72° F | 00000000 | 00000 |
8mm | M8 | 1 | Nickel-Plated Brass | Buna-N Rubber | 230 psi @ 72° F | 00000000 | 00000 |

(SAE Straight) Male
Threads with Gasket
Fittings with intermittent swivel rotate 360° before and after installation as needed to allow movement in the system and to prevent kinking.
Release Sleeve | |||||||
---|---|---|---|---|---|---|---|
For Tube OD | Thread Size | Thread Pitch, mm | Material | Gasket Material | Max. Pressure | Each | |
Metric Threads | |||||||
1/8" | M8 | 1 | Nickel-Plated Brass | Buna-N Rubber | 230 psi @ 72° F | 00000000 | 000000 |
1/4" | M8 | 1 | Nickel-Plated Brass | Buna-N Rubber | 230 psi @ 72° F | 00000000 | 00000 |
4mm | M8 | 1 | Nickel-Plated Brass | Buna-N Rubber | 230 psi @ 72° F | 00000000 | 00000 |
6mm | M8 | 1 | Nickel-Plated Brass | Buna-N Rubber | 230 psi @ 72° F | 00000000 | 00000 |
8mm | M8 | 1 | Nickel-Plated Brass | Buna-N Rubber | 230 psi @ 72° F | 00000000 | 00000 |
High-Temperature Brass Push-to-Connect Tube Fittings for Air and Water

- Temperature Range: 0° to 300° F
- Tubing: Use with firm or hard (Durometer 95A-65D) nylon plastic or polyurethane rubber
- Specifications Met: ISO 14743
These fittings have the highest temperature rating of all our brass push-to-connect tube fittings for air and water. Also known as instant fittings, they connect to tubing with a push, and an internal gripping ring and O-ring hold the tubing tight. To disconnect, push on the release ring and pull the tubing out of the fitting. They are nickel-plated for very good corrosion resistance.
For technical drawings and 3-D models, click on a part number.

For Tube OD | Thread Size | Thread Pitch, mm | Material | O-Ring Material | Max. Pressure | Each | |
Metric | |||||||
---|---|---|---|---|---|---|---|
4mm | M8 | 1 | Nickel-Plated Brass | Fluoroelastomer Rubber | 290 psi @ 72° F | 00000000 | 000000 |

Fittings with intermittent swivel rotate 360° before and after installation as needed to allow movement in the system and to prevent kinking.
For Tube OD | Thread Size | Thread Pitch, mm | Material | O-Ring Material | Max. Pressure | Each | |
Metric Threads | |||||||
---|---|---|---|---|---|---|---|
4mm | M8 | 1 | Nickel-Plated Brass | Fluoroelastomer Rubber | 290 psi @ 72° F | 00000000 | 000000 |
Plastic Barbed Tube Fittings for Air and Water
Fittings have barbs that grip onto tubing.
Nylon fittings have excellent impact and abrasion resistance.
For technical drawings and 3-D models, click on a part number.

- Temperature Range: See table
- Tubing: Semi-Clear: Use with firm or soft (Durometer 45A-80A) polyurethane rubber or PVC plastic
Opaque: Use with firm or soft (Durometer 40A-80A) polyurethane rubber or PVC plastic

- Temperature Range: See table
- Tubing: Semi-Clear: Use with firm or soft (Durometer 45A-80A) polyurethane rubber or PVC plastic
Opaque: Use with firm or soft (Durometer 40A-80A) polyurethane rubber or PVC plastic
For Tube ID | Thread Size | Material | Color | Clarity | Max. Pressure | Temp. Range, °F | Pkg. Qty. | Pkg. | |
Metric Threads | |||||||||
---|---|---|---|---|---|---|---|---|---|
4mm | M8 × 1 mm | Nylon Plastic | Gray | Opaque | 145 psi @ 72° F | -40° to 190° | 10 | 00000000 | 000000 |
Aluminum Low-Pressure Barbed Tube Fittings for Air and Water
- For Use With: Air, Lubricated Air, Water
- Temperature Range: -40° to 230° F
- Tubing: Use with hard (Durometer 75A-60D) EVA plastic, polyethylene plastic, polyurethane rubber or PVDF plastic
Made of aluminum, these fittings are lighter in weight than other metal barbed tube fittings and have good corrosion resistance. The barb grips onto tubing, providing a secure hold with no clamp required.
Metric, BSPP, and UN/UNF (SAE Straight) male threads have a gasket or O-ring for a tight seal.
For technical drawings and 3-D models, click on a part number.


(SAE Straight) Male
Threads with Gasket
Nickel-Plated Brass Low-Pressure Barbed Tube Fittings for Air and Water
The nickel plating on these brass fittings provides extra protection against corrosive environments. The plating won’t peel or chip, so the fittings keep a bright, polished appearance. The barbs grip onto tubing, providing a secure hold with no clamp required.
Metric male threads have a fiber gasket or O-ring for a tight seal.
For technical drawings and 3-D models, click on a part number.


(SAE Straight) and BSPP
Male Threads with Gasket
- Temperature Range: -40° to 230° F,
except UN/UNF (SAE Straight) Threads: -20° to 160° F - Tubing: Use with hard (Durometer 60D-90D) Buna-N rubber, EVA plastic, Nylon plastic, polyethylene plastic, polypropylene plastic, polyurethane rubber, PTFE plastic, PVC plastic, PVDF plastic, or silicone rubber,
except UN/UNF (SAE Straight) Threads: Use with firm (Durometer 85A) polyurethane rubber
Choose-a-Color Aluminum Low-Pressure Barbed Tube Fittings for Air and Water
- For Use With: Air, Lubricated Air, Water
- Temperature Range: -40° to 230° F
- Tubing: Use with hard (Durometer 75A-60D) EVA plastic, polyethylene plastic, polyurethane rubber or PVDF plastic
Color-code fittings for easy identification. Fittings are aluminum, which is lightweight with good corrosion resistance. The barb grips onto tubing, providing a secure hold with no clamp required.
Metric and UN/UNF (SAE Straight) male threads have a gasket for a tight seal.
For technical drawings and 3-D models, click on a part number.
Stainless Steel High-Pressure Barbed Tube Fittings for Air and Water
- Temperature Range: See table
- Tubing: Use with firm (Durometer 75A-95A) EVA plastic, polyethylene plastic, polypropylene plastic or PVC plastic
Fittings withstand pressures up to 250 psi. They are 303 stainless steel for very good corrosion resistance.
Metric, BSPP, and UN/UNF (SAE Straight) male threads have a gasket to protect against leaks.
For technical drawings and 3-D models, click on a part number.


UN/UNF (SAE Straight)
Male Threads with Gasket
For Tube ID | Thread Size | Thread Pitch, mm | Material | Gasket Material | Max. Pressure | Temp. Range, °F | Number of Barbs | Each | |
Metric Threads | |||||||||
---|---|---|---|---|---|---|---|---|---|
4mm | M8 | 1 | 303 Stainless Steel | Viton® Fluoroelastomer Rubber | 250 psi @ 72° F | -40° to 500° F | Single | 00000000 | 00000 |
6mm | M8 | 0.75 | 303 Stainless Steel | Viton® Fluoroelastomer Rubber | 250 psi @ 72° F | -40° to 500° F | Single | 00000000 | 00000 |
8mm | M8 | 1 | 303 Stainless Steel | Viton® Fluoroelastomer Rubber | 250 psi @ 72° F | -40° to 500° F | Single | 00000000 | 00000 |
Brass Quick-Turn Tube Couplings for Air

An all-brass body gives these couplings better strength and durability than plastic quick-turn couplings. They have a nickel plating for extra protection against corrosive environments. Also known as luer lock couplings, they consist of a plug and socket (sold separately) that connect with a half turn. They have a compact body, so they’re easy to fit in tight spaces. Plugs and sockets are open-flow style, so there is no shut-off valve to stop the flow when the coupling is separated. They have a universal connection, so the plugs will connect to any of the sockets, regardless of the pipe or tube size.
Note: For a complete coupling, order a plug and a socket.
For technical drawings and 3-D models, click on a part number.

- Temperature Range: -100° to 300° F
Thread Size | Thread Pitch, mm | Material | Max. Pressure | Features | Each | |
Metric Threads | ||||||
---|---|---|---|---|---|---|
M8 | 1 | Nickel-Plated Brass | 30 psi @ 72° F | Acrylic Thread Sealant | 00000000 | 000000 |

- Temperature Range: -100° to 300° F
Thread Size | Thread Pitch, mm | Material | Max. Pressure | Features | Each | |
Metric Threads | ||||||
---|---|---|---|---|---|---|
M8 | 1 | Nickel-Plated Brass | 30 psi @ 72° F | Acrylic Thread Sealant | 00000000 | 000000 |
Stainless Steel Push-to-Connect Tube Fittings for Chemicals


(SAE Straight) Male
Threads with Gasket
- For Use With: Alcohol, Bleach, Lubricated Air, Nitric Acid, Sodium Carbonate, Sulfuric Acid
- Temperature Range: 0° to 175° F
- Tubing: Use with firm or hard (Durometer 80A-60D) FEP, polyethylene, or PTFE plastic
Fittings are 316 stainless steel, which has excellent chemical resistance and is more durable than plastic. Also known as instant fittings, they connect to tubing with a push, and an internal gripping ring and O-ring hold the tubing tight. Instead of a release ring, these fittings have a release sleeve that slides back to disconnect tubing.
Metric and UN/UNF (SAE Straight) male threads have a gasket to protect against leaks. UN/UNF (SAE Straight) threads are also known as O-ring boss threads.
For technical drawings and 3-D models, click on a part number.


(SAE Straight) Male
Threads with Gasket
For Tube OD | Thread Size | Thread Pitch, mm | Material | Gasket Material | Max. Pressure | Each | |
Metric Threads | |||||||
---|---|---|---|---|---|---|---|
1/4" | M8 | 1 | 316 Stainless Steel | Viton® Fluoroelastomer Rubber | 345 psi @ 72° F | 00000000 | 000000 |
4mm | M8 | 1 | 316 Stainless Steel | Viton® Fluoroelastomer Rubber | 345 psi @ 72° F | 00000000 | 00000 |
6mm | M8 | 1 | 316 Stainless Steel | Viton® Fluoroelastomer Rubber | 345 psi @ 72° F | 00000000 | 00000 |
8mm | M8 | 1 | 316 Stainless Steel | Viton® Fluoroelastomer Rubber | 345 psi @ 72° F | 00000000 | 00000 |
Compression Fittings for Copper Tubing

- For Use With: Air, Cutting Oil, Fuel Oil, Hydraulic Fluid, Mineral Oil, Water
- Temperature Range: See Table
- Tubing: Use with copper
- Specifications Met: See Table
A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal. The nut and sleeve are included. Fittings are also known as flareless fittings. They are brass for good corrosion resistance.
For technical drawings and 3-D models, click on a part number.
Compression Fittings for Steel Tubing

- For Use With: Inch: Air, Hydraulic Fluid, Water
Metric: Hydraulic Fluid - Tubing: Inch: Use with welded steel
Metric: Use with seamless steel - Specifications Met: Inch: SAE J514
Metric: ISO 8434, DIN 2353
A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal. The nut and sleeve are included. Fittings are also known as flareless and bite fittings.
Zinc-plated steel fittings have fair corrosion resistance.
ISO 8434 (formerly DIN 2353) fittings meet international standards for tube fitting pressures.
For technical drawings and 3-D models, click on a part number.

- Temperature Range: See table
For Tube | ||||||||
---|---|---|---|---|---|---|---|---|
OD | Wall Thick. | Thread Size | Thread Pitch | Material | Max. Pressure | Temp. Range, °F | Each | |
Metric Taper Threads | ||||||||
4mm | Not Rated | M8 | 1 mm | Zinc-Plated Steel | 1,400 psi @ 72° F | -20° to 230° | 00000000 | 00000 |
Metal Barbed Hose Fittings for Air and Water
Slide the barbed end into rubber hose and secure with the appropriate clamp or crimp-on hose ferrule.
Brass fittings are softer than other metal fittings, so they’re easier to thread together. Plain brass fittings have good corrosion resistance.Aluminum fittings are lighter in weight than other metal fittings. They have good corrosion resistance.
Stainless steel fittings have very good corrosion resistance. 303 stainless steel fittings won’t rust when exposed to water, making them good for areas that require frequent cleanings. Fittings with a threaded end are also known as hose nipples.
Metric, UN/UNF (SAE Straight), and BSPP male threads with gasket protect against leaks.
For technical drawings and 3-D models, click on a part number.


UN/UNF (SAE Straight)
Male Threads with Gasket
- Maximum Pressure: See table
- Maximum Vacuum: 27 in. of Hg @ 72° F
- Temperature Range: See table
- Attachment Type: See table
- Specifications Met: See table
For Hose ID | Thread Size | Gasket Material | Max. Pressure | Temperature Range, °F | Attachment Type | Specifications Met | Pkg. Qty. | Pkg. | |
Brass | |||||||||
---|---|---|---|---|---|---|---|---|---|
1/4" | M8 × 1.25 mm | Buna-N Rubber | 300 psi @ 72° F | -30° to 200° | Worm-Drive Clamp, Band-and-Buckle Clamp, Crimp-On Hose Ferrule | __ | 1 | 00000000 | 000000 |
3/8" | M8 × 1.25 mm | Fiber | 250 psi @ 72° F | -40° to 160° | Worm-Drive Clamp, Crimp-On Hose Ferrule | SAE J476 | 1 | 0000000 | 00000 |
6mm | M8 × 1.25 mm | Buna-N Rubber | 300 psi @ 72° F | -30° to 200° | Worm-Drive Clamp, Band-and-Buckle Clamp, Crimp-On Hose Ferrule | __ | 1 | 00000000 | 00000 |
8mm | M8 × 1.25 mm | Fiber | 250 psi @ 72° F | -40° to 160° | Worm-Drive Clamp, Crimp-On Hose Ferrule | SAE J476 | 1 | 0000000 | 00000 |
9mm | M8 × 1.25 mm | Buna-N Rubber | 300 psi @ 72° F | -30° to 200° | Worm-Drive Clamp, Band-and-Buckle Clamp, Crimp-On Hose Ferrule | __ | 1 | 00000000 | 00000 |
10mm | M8 × 1.25 mm | Fiber | 250 psi @ 72° F | -40° to 160° | Worm-Drive Clamp, Crimp-On Hose Ferrule | SAE J476 | 1 | 0000000 | 00000 |
Aluminum | |||||||||
1/4" | M8 × 1.25 mm | Buna-N Rubber | 125 psi @ 72° F | -30° to 200° | Worm-Drive Clamp, Band-and-Buckle Clamp, Crimp-On Hose Ferrule | __ | 1 | 00000000 | 00000 |
3/8" | M8 × 1.25 mm | Buna-N Rubber | 125 psi @ 72° F | -30° to 200° | Worm-Drive Clamp, Band-and-Buckle Clamp, Crimp-On Hose Ferrule | __ | 1 | 00000000 | 0000 |
6mm | M8 × 1.25 mm | Buna-N Rubber | 125 psi @ 72° F | -30° to 200° | Worm-Drive Clamp, Band-and-Buckle Clamp, Crimp-On Hose Ferrule | __ | 1 | 00000000 | 00000 |
8mm | M8 × 1.25 mm | Buna-N Rubber | 125 psi @ 72° F | -30° to 200° | Worm-Drive Clamp, Band-and-Buckle Clamp, Crimp-On Hose Ferrule | __ | 1 | 00000000 | 00000 |
10mm | M8 × 1.25 mm | Buna-N Rubber | 125 psi @ 72° F | -30° to 200° | Worm-Drive Clamp, Band-and-Buckle Clamp, Crimp-On Hose Ferrule | __ | 1 | 00000000 | 00000 |
303 Stainless Steel | |||||||||
1/4" | M8 × 1.25 mm | Buna-N Rubber | 125 psi @ 72° F | -30° to 200° | Worm-Drive Clamp, Band-and-Buckle Clamp, Crimp-On Hose Ferrule | __ | 1 | 00000000 | 00000 |
3/8" | M8 × 1.25 mm | Buna-N Rubber | 125 psi @ 72° F | -30° to 200° | Worm-Drive Clamp, Band-and-Buckle Clamp, Crimp-On Hose Ferrule | __ | 1 | 00000000 | 00000 |
6mm | M8 × 1.25 mm | Buna-N Rubber | 125 psi @ 72° F | -30° to 200° | Worm-Drive Clamp, Band-and-Buckle Clamp, Crimp-On Hose Ferrule | __ | 1 | 00000000 | 00000 |
8mm | M8 × 1.25 mm | Buna-N Rubber | 125 psi @ 72° F | -30° to 200° | Worm-Drive Clamp, Band-and-Buckle Clamp, Crimp-On Hose Ferrule | __ | 1 | 00000000 | 00000 |
Metal Barbed Hose Fittings for Chemicals and Petroleum
Made of stainless steel, these fittings stand up to a wide variety of chemicals, as well as fuels, gasoline, and oils. To connect, slide the barbed end into plastic or rubber hose and secure with a clamp.
Adapters are also known as hose nipples; they adapt a barbed end to a threaded end.
Metric and UN/UNF (SAE Straight) male threads have a gasket to protect against leaks.
For technical drawings and 3-D models, click on a part number.

- For Use With: See table
- Maximum Pressure: See table
- Temperature Range: -40° to 300° F
- Attachment Type: Use Band-and-Buckle Clamps
Thread | |||||||
---|---|---|---|---|---|---|---|
For Hose ID | Size | Pitch, mm | Gasket Material | Max. Pressure | For Use With | Each | |
316 Stainless Steel | |||||||
1/4" | M8 | 1.25 | Fluoroelastomer Rubber | 125 psi @ 72° F | Acetone, Diesel Fuel, Ethanol, Fuel Oil, Gasoline, Mineral Oil, Mineral Spirits, Vegetable Oil | 00000000 | 000000 |
3/8" | M8 | 1.25 | Fluoroelastomer Rubber | 125 psi @ 72° F | Acetone, Diesel Fuel, Ethanol, Fuel Oil, Gasoline, Mineral Oil, Mineral Spirits, Vegetable Oil | 000000000 | 00000 |
3/8" | M8 | 1.25 | Viton® Fluoroelastomer Rubber | 250 psi @ 72° F | Acetone, Boric Acid, Citric Acid, Diesel Fuel, Ethanol, Fuel Oil, Gasoline, Mineral Oil, Mineral Spirits, Vegetable Oil | 000000000 | 00000 |
8mm | M8 | 1.25 | Viton® Fluoroelastomer Rubber | 250 psi @ 72° F | Acetone, Boric Acid, Citric Acid, Diesel Fuel, Ethanol, Fuel Oil, Gasoline, Mineral Oil, Mineral Spirits, Vegetable Oil | 000000000 | 00000 |
10mm | M8 | 1.25 | Viton® Fluoroelastomer Rubber | 250 psi @ 72° F | Acetone, Boric Acid, Citric Acid, Diesel Fuel, Ethanol, Fuel Oil, Gasoline, Mineral Oil, Mineral Spirits, Vegetable Oil | 000000000 | 00000 |
Right-Angle Flow Rectangular Manifolds
Distribute air or fluid to multiple locations from a single supply source with these manifolds. They are also known as headers. They have mounting holes, so you can mount from the top or side.
Aluminum manifolds are the industry standard for the most common types of applications. They are lighter in weight than other metal manifolds and have good corrosion resistance. Anodized aluminum manifolds have a black finish and nickel-plated aluminum manifolds have a shiny finish.
Use a plug (sold separately) to close off any unused inlets and outlets.
For technical drawings and 3-D models, click on a part number.

- For Use With: Air, Water, Hydraulic Fluid
- Temperature Range: See table
- Maximum Pressure:
Air: 1,000 psi @ 72° F
Water: 1,000 psi @ 72° F
Hydraulic Fluid: See table - Maximum Vacuum: 27 in. of Hg @ 72° F
Inlet | Outlet | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
No. of Outlets | Thread Size | Thread Pitch, mm | Thread Size | Thread Pitch, mm | Lg., mm | Wd., mm | Ht., mm | Outlet Ctr.-to-Ctr., mm | Color | Maximum Pressure, Hydraulic Fluid | Temperature Range, °F | Each | |
Outlets on One Side—Standard Outlet Spacing | |||||||||||||
4 | M8 | 1.25 | M5 | 0.8 | 76 | 19 | 19 | 16 | Black | 3,000 psi @ 72° F | -65° to 250° | 00000000 | 000000 |
6 | M8 | 1.25 | M6 | 1 | 108 | 19 | 19 | 16 | Black | 3,000 psi @ 72° F | -65° to 250° | 00000000 | 00000 |
Low-Profile Hex Manifolds
When you’re short on vertical space, these manifolds are a good fit—they have outlets on the side instead of on top, so they have a lower profile than rectangular manifolds. Use them to distribute air, water, or hydraulic fluid to five locations from a single supply source. Manifolds have mounting holes, so you can mount from the top.
Anodized aluminum manifolds are the industry standard for the most common types of applications. They are lighter in weight than other metal manifolds and have good corrosion resistance. These manifolds are anodized for a black finish.
316 stainless steel manifolds have excellent corrosion resistance and can handle fuel, gasoline, coolant and other harsh substances.
Use a plug (sold separately) to close off any unused inlets and outlets.
For technical drawings and 3-D models, click on a part number.


- For Use With: Air, Water, Hydraulic Fluid
- Temperature Range: -10° to 200° F
- Maximum Pressure: 1,000 psi @ 72° F
- Maximum Vacuum: 27 in. of Hg @ 72° F


- For Use With: Air, Water, Hydraulic Fluid, Alcohol, Coolant, Cutting Oil, Deionized Water, Diesel Fuel, Fuel Oil, Gasoline, Mineral Oil, Nitrogen
- Temperature Range: -100° to 500° F
- Maximum Pressure: 3,500 psi @ 72° F
- Maximum Vacuum: 27 in. of Hg @ 72° F
External Hex Drive | |||||
---|---|---|---|---|---|
Thread Size | Thread Pitch, mm | Max. Pressure | Pressure Class | Each | |
Aluminum—Metric | |||||
M6 | 1 | 150 psi @ 72° F | 150 | 00000000 | 00000 |
Straight-Flow Junction Blocks

Use these junction blocks to organize and separate multiple lines in your system. They have threaded holes that allow air, water, or hydraulic fluid to flow straight through the block. They have mounting holes, so you can mount from the side.
Anodized aluminum junction blocks are lightweight with good corrosion and wear resistance.
For technical drawings and 3-D models, click on a part number.

- For Use With: Air, Water, Hydraulic Fluid
- Temperature Range: -10° to 200° F
- Maximum Pressure:
Air: 1,000 psi @ 72° F
Water: 1,000 psi @ 72° F
Hydraulic Fluid: 3,000 psi @ 72° F - Maximum Vacuum: Not Rated
Inlet | Outlet | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
No. of Outlets | Thread Size | Thread Pitch, mm | Thread Size | Thread Pitch, mm | Lg., mm | Wd., mm | Ht., mm | Outlet Ctr.-to-Ctr., mm | Outlet Spacing | Color | Each | |
4 | M8 | 1.25 | M8 | 1.25 | 127 | 19 | 19 | 16 | Standard | Black | 00000000 | 000000 |
Grease Fitting Adapters
When the size or thread type of a fitting doesn't match an existing opening, use these adapters to make the connection.
Zinc-plated steel adapters have mild corrosion resistance. Brass adapters resist corrosion better than zinc-plated steel adapters. UNF threads are similar to threads on a machine screw or bolt. They require a sealant, such as an O-ring, to minimize leakage.
For technical drawings and 3-D models, click on a part number.
Button-Head Grease Fittings
Often used on earth movers, mining equipment, and other heavy machinery, these fittings have a T-shaped top that holds the dispensing tip in place so it won’t pop off when adding grease. They're best for machinery requiring high volumes of grease because they let more grease pass through than standard grease fittings, thanks to a larger opening. An integral check valve prevents grease from leaking when pressure causes backward flow. The valve stays closed when not in use to keep out dirt and other contaminants.
Zinc-plated steel fittings have mild corrosion resistance.
For technical drawings and 3-D models, click on a part number.

Each | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
Material | Overall Ht. | Thread Lg. | Shank Lg. | Hex Size | Head Dia. | Max. Pressure, psi | Check Valve Type | Specifications Met | 1-9 | 10-Up | |
M8 × 1 mm Metric Threads | |||||||||||
Zinc-Plated Steel | 14mm | 6mm | 6mm | 11mm | 10mm | 1,450 | Ball | DIN 3404 | 0000000 | 00000 | 00000 |