How to Identify and Measure Fittings
Pipe size is an industry designation, not the actual size. View information about how to measure threaded and unthreaded pipe and pipe fittings.
More
Butt-Weld Fittings for Stainless Steel Tubing
- For Use With: See table
- Temperature Range: See table
- Tubing:
304 Stainless Steel: Use with 304/304L stainless steel that meets ASTM A213, ASTM A269, or ASTM A270, except DIN EN 10357 fittings with only ASTM A269 or ASTM A270
316 Stainless Steel: Use with 316/316L stainless steel that meets ASTM A213, ASTM A269, or ASTM A270, except ASME BPE and DIN EN 10357 fittings with only ASTM A269 or ASTM A270 - Specifications Met: See table
Weld these fittings to tubing for a permanent, flush connection that permits smooth flow through a line.
316 stainless steel fittings have excellent corrosion resistance.
For technical drawings and 3-D models, click on a part number.
High-Polish Metal Quick-Clamp Sanitary Tube Fittings
- Temperature Range: See Gaskets
The smooth finish inside these fittings makes it easy to remove product residue. Also known as aseptic and tri-clamp fittings, they connect with a gasket, a clamp, and another quick-clamp fitting for a fast and easy way to access your line. The pressure rating of the fitting will vary depending on the clamp you choose, and the temperature rating will vary based on the gasket material you choose.
304 stainless steel fittings have very good corrosion resistance. 316 stainless steel fittings have excellent corrosion resistance.
3-A certified fittings comply with sanitary standards.
Note: To complete a connection, you’ll need two quick-clamp fittings, a clamp, and a gasket (all sold separately).
For technical drawings and 3-D models, click on a part number.
- For Use With: Air, Beverage, Dairy, Food, Water
- Tubing: Use with welded 304/304L or 316/316L stainless steel that meets ASTM A269 or ASTM 270
- Specifications Met: 3-A Certified 63-04
| For Tube OD | For Flange OD | Max. Pressure | For Tube Specifications Met | Each | |
| 1/4", 3/8", 1/2", 5/8", 3/4" | 0.984" | 1,200 psi @ 72° F | ASTM A269, ASTM A270 | 00000000 | 00000 |
| For Tube OD | For Flange OD | Max. Pressure | For Tube Specifications Met | Each | |
| 1/2", 3/4" | 0.984" | 1,200 psi @ 72° F | ASTM A269, ASTM A270 | 0000000 | 000000 |
| For Tube OD | For Flange OD | Max. Pressure | Each | |
| 1/2", 3/4" | 0.984" | 700 psi @ 72° F | 0000000 | 000000 |
| For Tube OD | For Flange OD | Max. Pressure | Each | |
| 1/2", 3/4" | 0.984" | 720 psi @ 72° F | 0000000 | 000000 |
Recessed Nut, Hole for
Lockout, and 2-Pin Hinge
| For Tube OD | For Flange OD | Max. Pressure | Each | |
| 1/2", 3/4" | 0.984" | 720 psi @ 72° F | 0000000 | 000000 |
| For Tube OD | For Flange OD | Max. Pressure | For Tube Specifications Met | Each | |
| 1/2", 3/4" | 0.984" | 150 psi @ 72° F | ASTM A269, ASTM A270 | 00000000 | 000000 |
Buna-N gaskets are oil resistant. EPDM gaskets resist water and steam and work well in humid environments. Silicone gaskets withstand high temperatures. Fluoroelastomer gaskets stand up to fuel, oil, and acid condensates. PTFE gaskets withstand harsh chemicals, with the exception of molten alkali metal and elemental fluorine.
| For Tube OD | ID | OD | Thick. | Temp. Range, °F | Color | Specifications Met | Each | |
Buna-N Rubber | ||||||||
|---|---|---|---|---|---|---|---|---|
| 1/2" | 0.380" | 0.860" | 0.178" | -30° to 200° | Black | 3-A Certified 18-03, FDA Compliant 21 CFR 177.1550, FDA Compliant 21 CFR 177.2600 | 0000000 | 00000 |
| 3/4" | 0.620" | 0.860" | 0.178" | -30° to 200° | Black | 3-A Certified 18-03, FDA Compliant 21 CFR 177.1550, FDA Compliant 21 CFR 177.2600 | 0000000 | 0000 |
EPDM Rubber | ||||||||
| 1/2" | 0.380" | 0.860" | 0.178" | -20° to 300° | Black | 3-A Certified 18-03, FDA Compliant 21 CFR 177.1550, FDA Compliant 21 CFR 177.2600 | 0000000 | 0000 |
| 3/4" | 0.620" | 0.860" | 0.178" | -20° to 300° | Black | 3-A Certified 18-03, FDA Compliant 21 CFR 177.1550, FDA Compliant 21 CFR 177.2600 | 0000000 | 0000 |
Silicone Rubber | ||||||||
| 1/2" | 0.380" | 0.860" | 0.178" | -40° to 450° | Clear | 3-A Certified 18-03, FDA Compliant 21 CFR 177.1550, FDA Compliant 21 CFR 177.2600 | 0000000 | 0000 |
| 3/4" | 0.620" | 0.860" | 0.178" | -40° to 450° | Clear | 3-A Certified 18-03, FDA Compliant 21 CFR 177.1550, FDA Compliant 21 CFR 177.2600 | 0000000 | 0000 |
Fluoroelastomer Rubber | ||||||||
| 1/2" | 0.380" | 0.860" | 0.178" | -15° to 400° | Black | 3-A Certified 18-03, FDA Compliant 21 CFR 177.2600 | 0000000 | 0000 |
| 3/4" | 0.620" | 0.860" | 0.178" | -15° to 400° | Black | 3-A Certified 18-03, FDA Compliant 21 CFR 177.2600 | 0000000 | 0000 |
PTFE Plastic  | ||||||||
| 1/2" | 0.380" | 0.860" | 0.178" | -100° to 500° | White | 3-A Certified 20-27, FDA Compliant 21 CFR 177.1550 | 00000000 | 0000 |
| 3/4" | 0.620" | 0.860" | 0.178" | -100° to 500° | White | 3-A Certified 20-27, FDA Compliant 21 CFR 177.1550 | 00000000 | 0000 |
Extra-High-Polish Metal Quick-Clamp Sanitary Tube Fittings
- For Use With: Air, Beverage, Dairy, Deionized Water, Food, Pharmaceuticals, Water
- Temperature Range: See Gaskets
- Tubing:
Fittings with 700 psi @ 72° F max. pressure: Use with 316/316L stainless steel that meets ASTM A269 or ASTM A270
Fittings with all other max. pressures: Use with 316/316L stainless steel that meets ASTM A249, ASTM A269, or ASTM A270
Gaskets: Use with 304/304L and 316/316L stainless steel - Specifications Met: See table
- Certification: Material Certificate with Traceable Lot Number and Test Report
Polished to a 20 Ra finish, these fittings have an extra-smooth interior that prevents product buildup and inhibits bacteria growth. Use them in pharmaceutical and bioprocessing applications. Also known as tri-clamp fittings, they connect with a clamp, a gasket, and another quick-clamp fitting for a fast and easy way to access your line. Fittings are 316 stainless steel for excellent corrosion resistance.
The pressure rating of the fitting will depend on the clamp you choose.
The temperature rating of the fitting will vary depending on the gasket material you choose.
Note: To complete a connection, you’ll need two quick-clamp fittings, a clamp, and a gasket (all sold separately).
For technical drawings and 3-D models, click on a part number.
| For Tube OD | Flange OD | Length | Material | Max. Pressure | Specifications Met | Each | |
| 1/2", 3/4" | 0.984" | 3/16" | 316/316L Stainless Steel | 700 psi @ 72° F | ASME BPE | 0000000 | 000000 |
| For Tube OD | For Flange OD | Max. Pressure | For Tube Specifications Met | Each | |
| 1/4", 3/8", 1/2", 5/8", 3/4" | 0.984" | 1,200 psi @ 72° F | ASTM A269, ASTM A270 | 00000000 | 00000 |
| For Tube OD | For Flange OD | Max. Pressure | For Tube Specifications Met | Each | |
| 1/2", 3/4" | 0.984" | 1,200 psi @ 72° F | ASTM A269, ASTM A270 | 0000000 | 000000 |
| For Tube OD | For Flange OD | Max. Pressure | Each | |
| 1/2", 3/4" | 0.984" | 700 psi @ 72° F | 0000000 | 000000 |
| For Tube OD | For Flange OD | Max. Pressure | Each | |
| 1/2", 3/4" | 0.984" | 720 psi @ 72° F | 0000000 | 000000 |
Recessed Nut, Hole for
Lockout, and 2-Pin Hinge
| For Flange OD [Nom] | For Tube OD | For Flange OD | Max. Pressure | Each | |
| 0.984" | 1/2", 3/4" | 0.984" | 720 psi @ 72° F | 0000000 | 000000 |
| For Tube OD | For Flange OD | Max. Pressure | For Tube Specifications Met | Each | |
| 1/2", 3/4" | 0.984" | 150 psi @ 72° F | ASTM A269, ASTM A270 | 00000000 | 000000 |
Buna-N gaskets are oil resistant. EPDM gaskets resist water and steam and work well in humid environments. Silicone gaskets withstand high temperatures. Fluoroelastomer gaskets stand up to fuel, oil, and acid condensates. PTFE gaskets withstand harsh chemicals, with the exception of molten alkali metal and elemental fluorine.
| For Tube OD | ID | OD | Thick. | Temp. Range, °F | Color | Specifications Met | Each | |
Buna-N Rubber | ||||||||
|---|---|---|---|---|---|---|---|---|
| 1/2" | 0.380" | 0.860" | 0.178" | -30° to 200° | Black | 3-A Certified 18-03, FDA Compliant 21 CFR 177.1550, FDA Compliant 21 CFR 177.2600 | 0000000 | 00000 |
EPDM Rubber | ||||||||
| 1/2" | 0.380" | 0.860" | 0.178" | -20° to 300° | Black | 3-A Certified 18-03, FDA Compliant 21 CFR 177.1550, FDA Compliant 21 CFR 177.2600 | 0000000 | 0000 |
Silicone Rubber | ||||||||
| 1/2" | 0.380" | 0.860" | 0.178" | -40° to 450° | Clear | 3-A Certified 18-03, FDA Compliant 21 CFR 177.1550, FDA Compliant 21 CFR 177.2600 | 0000000 | 0000 |
Fluoroelastomer Rubber | ||||||||
| 1/2" | 0.380" | 0.860" | 0.178" | -15° to 400° | Black | 3-A Certified 18-03, FDA Compliant 21 CFR 177.2600 | 0000000 | 0000 |
PTFE Plastic | ||||||||
| 1/2" | 0.380" | 0.860" | 0.178" | -100° to 500° | White | 3-A Certified 20-27, FDA Compliant 21 CFR 177.1550 | 00000000 | 0000 |
Quick-Clamp High-Vacuum Fittings for Stainless Steel Tubing
- For Use With:
Fittings with Gasket End: Air, Argon, Helium, Nitrogen
All Other Fittings: Air - Temperature Range: 0° to 300° F
- Tubing: Use with 304/304L or 316/316L stainless steel
- Specifications Met: ISO 2861
Instead of a gasket, these fittings have a special ring that is designed for high-vacuum applications, such as vacuum coating and heat treating, leak testing, and analyzing gases. Also known as KF, QF, and NW fittings, they are the most common type of connection in high-vacuum systems. Connect with a clamp and another quick-clamp fitting for fast, easy access to your line. To use fittings in pressure applications, use a pressure-rated ring (sold separately).
304 stainless steel fittings have very good corrosion resistance.
Note: To complete a connection, you’ll need two quick-clamp fittings, a ring, and a clamp (all sold separately).
For technical drawings and 3-D models, click on a part number.
| For Tube OD | Flange OD | High-Vacuum Flange Size | High Vacuum Connection Type | Material | Max. Vacuum | Each | |
| 3/4" | 1.18" | 16 | ISO-KF | 304 Stainless Steel | 1 × 10 -7 torr @ 72° F | 00000000 | 000000 |
Clamps tighten by hand. Spring-loaded clamps are also known as toggle clamps.
| For Tube OD | For Flange OD | For High-Vacuum Flange Size | High Vacuum Connection Type | Material | Max. Vacuum | Lanyard Length | Each | |
with Wing Nut | ||||||||
|---|---|---|---|---|---|---|---|---|
| 1/2", 3/4" | 1.18" | 10, 16 | ISO-KF | Aluminum | 1 × 10 -7 torr @ 72° F | __ | 00000000 | 00000 |
Spring Loaded | ||||||||
| 1/2", 3/4" | 1.18" | 10, 16 | ISO-KF | Aluminum | 1 × 10 -7 torr @ 72° F | __ | 0000000 | 00000 |
Spring Loaded with Lanyard | ||||||||
| 3/4" | 1.18" | 16 | ISO-KF | Aluminum | 1 × 10 -7 torr @ 72° F | 5 3/4" | 00000000 | 00000 |
Use these rings with quick-clamp high-vacuum fittings. They consist of a stainless steel inner ring covered by a fluoroelastomer O-ring.
| For Tube OD | For Flange OD | For High-Vacuum Flange Size | High Vacuum Connection Type | Inner Ring Material | Max. Vacuum | Max. Pressure | Each | |
Rings | ||||||||
|---|---|---|---|---|---|---|---|---|
| 3/4" | 1.18" | 16 | ISO-KF | 304 Stainless Steel | 1 × 10 -7 torr @ 72° F | Not Rated | 00000000 | 00000 |
Rings with Stainless Steel Screen | ||||||||
| 3/4" | 1.18" | 16 | ISO-KF | 304 Stainless Steel | 1 × 10 -7 torr @ 72° F | Not Rated | 00000000 | 00000 |
Rings with Aluminum Outer Ring | ||||||||
| 3/4" | 1.18" | 16 | ISO-KF | 304 Stainless Steel | 1 × 10 -7 torr @ 72° F | Not Rated | 00000000 | 00000 |
Hose absorbs moderate vibration
| For Tube OD | Flange OD | High-Vacuum Flange Size | High Vacuum Connection Type | Material | Max. Vacuum | Bend Radius | Flexibility | Each | |
3 3/16" Lg. | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| 3/4" | 1.18" | 16 | ISO-KF | 304 Stainless Steel | 1 × 10 -7 torr @ 72° F | __ | Rigid | 0000000 | 000000 |
12" Lg. | |||||||||
| 3/4" | 1.18" | 16 | ISO-KF | 304 Stainless Steel | 1 × 10 -7 torr @ 72° F | 1 5/8" | Flexible | 00000000 | 000000 |
24" Lg. | |||||||||
| 3/4" | 1.18" | 16 | ISO-KF | 304 Stainless Steel | 1 × 10 -7 torr @ 72° F | 1 5/8" | Flexible | 00000000 | 000000 |
39" Lg. | |||||||||
| 3/4" | 1.18" | 16 | ISO-KF | 304 Stainless Steel | 1 × 10 -7 torr @ 72° F | 1 5/8" | Flexible | 00000000 | 000000 |
Valves are also known as vacuum isolation valves. They connect to a vacuum system so you can install gauges, release gases, and remove air. They operate manually and have a compact body that fits easily into tight spaces.
| Actuation | For Tube OD | Flange OD | High-Vacuum Flange Size | Max. Vacuum | Body Material | Overall Ht. | Overall Lg. | Each | |
| Manual | 3/4" | 1 3/16" | 16 | 10 -7 torr @ 72° F | 304 Stainless Steel | 4 1/8" | 2 1/4" | 00000000 | 0000000 |
Compression Fittings for Stainless Steel Tubing
For technical drawings and 3-D models, click on a part number.
- For Use With: Air, Hydraulic Fluid, Water
- Temperature Range: -420° to 1200° F
- Tubing: Use with welded or seamless 304 or 316 stainless steel that meets ASTM A269
- Specifications Met: SAE J514
For Tube | |||||
|---|---|---|---|---|---|
| OD | Wall Thick. | Material | Max. Pressure | Each | |
| 3/4" | 0.065" | 316 Stainless Steel | 1,900 psi @ 72° F | 000000000 | 000000 |
- For Use With: Air, Hydraulic Fluid, Water
- Temperature Range: -420° to 1200° F
- Tubing: Use with seamless 304 or 316 stainless steel that meets ASTM A269
- Specifications Met: SAE J514
Plugs insert into the end of a fitting.
For Tube | |||||
|---|---|---|---|---|---|
| OD | Wall Thick. | Material | Max. Pressure | Each | |
| 3/4" | 0.065" | 316 Stainless Steel | 4,500 psi @ 72° F | 000000000 | 000000 |
- For Use With: See table
- Temperature Range: See table
- Tubing: See table
- Specifications Met: See table
For Tube | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Wall Thick. | Nut Material | Max. Pressure | For Use With | Temp. Range, °F | For Tube Material | For Tube Specifications Met | For Tube Fabrication | Specifications Met | Each | |
| 3/4" | 0.065" | 316 Stainless Steel | 1,900 psi @ 72° F | Air, Hydraulic Fluid, Water | -420° to 1200° | 304 Stainless Steel, 316 Stainless Steel | ASTM A269 | Seamless, Welded | SAE J514 | 000000000 | 000000 |
- For Use With:
17-4 PH Stainless Steel: Air, Hydraulic Fluid, Water
316 Stainless Steel: Air, Cutting Oil, Ethyl Alcohol, Fuel Oil, Gasoline, Hydraulic Fluid, Isopropyl Alcohol, Mineral Oil, Natural Gas, Steam, Water - Temperature Range:
17-4 PH Stainless Steel: -420° to 1200° F
316 Stainless Steel: -75° to 750° F - Tubing:
17-4 PH Stainless Steel: Use with welded or seamless 304 or 316 stainless steel that meets ASTM A269
316 Stainless Steel: Use with seamless 304 or 316/316L/316Ti stainless steel that meets DIN EN 10216-5 or DIN EN 10305-1 - Specifications Met:
17-4 PH Stainless Steel: SAE J514
316 Stainless Steel: ISO 8434-1, DIN 2353
For Tube | |||||
|---|---|---|---|---|---|
| OD | Wall Thick. | Sleeve Material | Max. Pressure | Each | |
| 3/4" | 0.065" | 17-4 PH Stainless Steel | 1,900 psi @ 72° F | 000000000 | 00000 |
Precision Compression Fittings for Stainless Steel Tubing
- For Use With: Air, Cutting Oil, Ethyl Alcohol, Fuel Oil, Gasoline, Hydraulic Fluid, Isopropyl Alcohol, Mineral Oil, Natural Gas, Steam, Water
- Temperature Range: -420° to 1200° F
- Tubing: Use with welded or seamless 304 or 316 stainless steel that meets ASTM A213, ASTM A249, or ASTM A269
- Compatible With: Parker CPI
Made to tighter tolerances than other compression fittings, these are designed for high-precision applications. Also known as instrumentation fittings and flareless fittings. They come with a nut and a single sleeve (ferrule). The sleeve bites into tubing as you tighten the nut to create a strong seal. Fittings are 316 stainless steel for excellent corrosion resistance. A molybdenum disulfide coating on the nut acts as a lubricant for easy installation.
For technical drawings and 3-D models, click on a part number.
Caps for tubing have a nut and a sleeve so you can close off the end of your tubing in place of a fitting. Caps for fittings replace the nut and sleeve of an existing fitting.
For Tube | ||||
|---|---|---|---|---|
| OD | Wall Thick. | Nut Material | Max. Pressure | |
| 3/4" | 0.049" | Molybdenum-Disulfide-Coated 316 Stainless Steel | 2,100 psi @ 72° F | 00000000 |
For Tube | ||||
|---|---|---|---|---|
| OD | Wall Thick. | Sleeve Material | Max. Pressure | |
| 3/4" | 0.049" | 316 Stainless Steel | 2,100 psi @ 72° F | 00000000 |
Yor-Lok Fittings for Stainless Steel Tubing
A nut with two sleeves (ferrules) gives these fittings extra gripping power. The sleeves bite into tubing as you tighten the nut, creating a strong seal. Also known as instrumentation fittings, they are made to tight tolerances for use in high-precision applications. They are compatible with Swagelok®, Let-Lok, and A-Lok fittings.
316 stainless steel fittings have excellent corrosion resistance.
For technical drawings and 3-D models, click on a part number.
- For Use With: Air, Cutting Oil, Fuel Oil, Gasoline, Hydraulic Fluid, Mineral Oil, Natural Gas, Steam, Water
- Tubing: Use with welded or seamless 304/304L or 316/316L stainless steel that meets ASTM A213, ASTM A249, or ASTM A269
Caps for tubing have a nut and a sleeve so you can close off the end of your tubing in place of a fitting. Caps for fittings replace the nut and sleeve of an existing fitting.
For Tube | ||||||
|---|---|---|---|---|---|---|
| OD | Wall Thick. | Nut Material | Max. Pressure | Temp. Range, °F | Each | |
| 3/4" | 0.049" | 316 Stainless Steel | 2,000 psi @ 72° F | -420° to 1200° | 00000000 | 000000 |
For Tube | ||||||
|---|---|---|---|---|---|---|
| OD | Wall Thick. | Sleeve Material | Max. Pressure | Temp. Range, °F | Each | |
| 3/4" | 0.049" | 316 Stainless Steel | 2,000 psi @ 72° F | -420° to 1200° | 00000000 | 00000 |
PTFE sleeves are plastic instead of stainless steel, so they won’t damage tubing.
| For Tube OD | Sleeve Material | Max. Pressure | Temp. Range, °F | Each | |
| 3/4" | PTFE Plastic | Not Rated | -65° to 350° | 00000000 | 000000 |
Tube supports are recommended for soft plastic tubing to prevent the tube from collapsing.
For Tube | |||||
|---|---|---|---|---|---|
| OD | ID | Tube Support Material | Temp. Range, °F | Each | |
| 3/4" | 1/2" | 316 Stainless Steel | -420° to 1200° | 00000000 | 000000 |
37° Flared Fittings for Stainless Steel Tubing
- Tubing: Use with welded or seamless 304 or 316 stainless steel that meets ASTM A213, ASTM A249, or ASTM A269
- Specifications Met: ISO 8434, SAE J514, except fittings with BSPP and BSPT threads meet SAE J514 only
Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on tubing that is flared to 37°. They withstand high pressure, so they’re often used in hydraulic applications. Made from 316 stainless steel, they resist corrosion from water and chemicals. A complete fitting requires a nut and a sleeve (ferrule) for each tube end. Nuts and sleeves are sold separately.
For technical drawings and 3-D models, click on a part number.
- For Use With: Air, Hydraulic Fluid, Isopropyl Alcohol, Natural Gas, Phosphoric Acid, Water
- Temperature Range: See table
| For Tube OD | Material | Temp. Range, °F | Each | |
| 3/4" | 316 Stainless Steel | -420° to 1200° | 000000000 | 000000 |
- For Use With: Air, Hydraulic Fluid, Isopropyl Alcohol, Natural Gas, Phosphoric Acid, Water
- Temperature Range: See table
| For Tube OD | Material | Temp. Range, °F | Each | |
| 3/4" | 316 Stainless Steel | -420° to 1200° | 000000000 | 000000 |
- For Use With: Air, Hydraulic Fluid, Isopropyl Alcohol, Natural Gas, Phosphoric Acid, Water
- Temperature Range: -420° to 1,200° F
| For Tube OD | Nut Material | Each | |
| 3/4" | 316 Stainless Steel | 000000000 | 000000 |
- For Use With: Air, Hydraulic Fluid, Isopropyl Alcohol, Natural Gas, Phosphoric Acid, Water
- Temperature Range: -420° to 1,200° F
Use these sleeves with a nut and fitting to provide a tight metal-to-metal seal on stainless steel tubing that is flared to 37°. Sleeves are 316 stainless steel for excellent corrosion resistance. They are also known as ferrules.
For Tube OD | |||
|---|---|---|---|
| Inch | Sleeve Material | Each | |
Inch | |||
| 3/4" | 316 Stainless Steel | 000000000 | 000000 |
Precision AN 37° Flared Fittings for Stainless Steel Tubing
- For Use With: Air, Cutting Oil, Fuel Oil, Hydraulic Fluid, Mineral Oil, Water
- Temperature Range: -320° to 1200° F
- Tubing: Use with seamless 304 or 316 stainless steel
- Specifications Met: See Table
The threads on the tube end of these fittings are Class 3A or 3B and adhere to tighter tolerances than other 37° flared fittings. They are made to exact AS (formerly AN) specifications and provide a tight metal-to-metal seal on tubing that is flared to 37°. Fittings require a nut and a sleeve (ferrule) for each tube end. Nuts and sleeves are sold separately.
304 stainless steel fittings have very good corrosion resistance. 316 stainless steel fittings have excellent corrosion resistance.
For technical drawings and 3-D models, click on a part number.
Vibration-Resistant Precision AN 37° Flared Fittings for Stainless Steel Tubing
- For Use With: Air, Cutting Oil, Fuel Oil, Hydraulic Fluid, Mineral Oil, Water
- Temperature Range: -320° to 500° F
- Tubing: Use with seamless 304 or 316 stainless steel
- Specifications Met: See Table
A PTFE seal on the tube end of these fittings allows for an extra-strong connection in high-vibration applications. The threads on the tube end are Class 3A and adhere to tighter tolerances than other 37° flared fittings. They are made to exact AS (formerly AN) specifications and provide a tight metal-to-metal seal on tubing that is flared to 37°. Fittings are 316 stainless steel for excellent corrosion resistance. They require a nut and a sleeve (ferrule) for each tube end. Nuts and sleeves are sold separately.
For technical drawings and 3-D models, click on a part number.
| For Tube OD | Material | Max. Pressure | Specifications Met | Each | |
| 3/4" | 316 Stainless Steel | 3,000 psi @ 72° F | ASTM A380, SAE AS9100D, SAE AS9104/1 | 00000000 | 000000 |
| For Tube OD | Nut Material | Max. Pressure | Specifications Met | Each | |
| 3/4" | 316 Stainless Steel | 3,000 psi @ 72° F | AN818-12K, ASTM A380, SAE AS4841 | 00000000 | 000000 |
| For Tube OD | Sleeve Material | Max. Pressure | Specifications Met | Each | |
| 3/4" | 316 Stainless Steel | 3,000 psi @ 72° F | AN819-12K, ASTM A380, MS20819, SAE AS4841 | 00000000 | 000000 |
Ultra-High-Vacuum Flanges and Fittings for Stainless Steel Tubing
- For Use With: Air
- Temperature Range:
Flanges: -300° to 800° F
Gaskets: Not Rated - Tubing: Use with 304/304L and 316/316L stainless steel
- Specifications Met:
Flanges: ASTM A240, ASTM E45, ASTM E12
Gaskets: ASTM B152-179, ASTM F68
Create access points in ultra-high-vacuum lines or chambers by bolting two same-size flanges together with a copper gasket (sold separately) between them. The flanges’ sharp edges dig into the copper gasket and form an extremely tight seal, which means they handle higher vacuum pressures than other high-vacuum fittings with rubber gaskets. Also known as CF, Conflat, and UHV fittings, use them in vacuum coating, heat treating, and drying applications, as well as for leak testing and analyzing gases. They’re stainless steel so they resist rusting.
Caps are also known as blind flanges.
Bolt kits are required to make a complete connection.
For technical drawings and 3-D models, click on a part number.
Bolt Hole | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Tube OD | Flange OD | High-Vacuum Flange Size | High Vacuum Connection Type | Bolt Circle Dia. | Dia. | No. of | Bolts Included | No. of Bolt Kits Required | Lg. | Max. Vacuum | Material | Appearance | Each | |
Fixed | ||||||||||||||
| 3/4" | 1 21/64" | 16 | CF | 1 1/16" | 11/64" | 6 | No | 1 | 5/16" | 1 × 10 -13 torr @72° F | 304 Stainless Steel | Polished | 0000000 | 000000 |
| For Tube OD | For Flange OD | Gasket Material | Specifications Met | Each | |
| 3/4" | 1 21/64" | Copper | ASTM F68 | 0000000 | 00000 |
| For Flange OD | For High-Vacuum Flange Size | Bolt Dia. | Thread Size | No. of Bolts Included | No. of Nuts Included | No. of Washers Included | Bolt Material | Each | |
| 1 21/64" | 16 | 0.164" | 8-32 | 6 | 6 | 12 | 18-8 Stainless Steel | 0000000 | 00000 |
Solder-Connect Fittings for Copper Tubing
- Temperature Range: 32° to 200° F
Solder these fittings to copper tubing or the tube end of another fitting for a permanent, leak-tight connection. They are also known as sweat fittings. Fittings have good corrosion resistance. To adhere to safety standards for drinking water systems, use fittings that meet NSF/ANSI 61 or EN 1057.
Copper tube size is the accepted designation of the copper tubing industry, not the actual tube OD.
For technical drawings and 3-D models, click on a part number.
- For Use With: Drinking Water
- Tubing: See table
- Specifications Met: See table
| (Web) Table Pivot | Copper Tube Size | For Tube OD | Material | Max. Pressure | For Copper Tube Type | Specifications Met | Each | |
| 1 | 5/8 | 3/4" | Copper | 400 psi @ 72° F | K, M, L | ASME B16.22, MSS-SP104, NSF/ANSI 61 | 00000000 | 00000 |
Yor-Lok Fittings for Copper Tubing
- For Use With: Air, Cutting Oil, Diesel Fuel, Fuel Oil, Gasoline, Hydraulic Fluid, Mineral Oil, Water
- Temperature Range: -40° to 400° F
- Tubing: Use with seamless copper
- Specifications Met: ASME B31.3
A nut with two sleeves (ferrules) gives these fittings extra gripping power. The sleeves bite into tubing as you tighten the nut, creating a strong seal. Also known as instrumentation fittings, they are made to tight tolerances for use in high-precision applications. Fittings are brass for good corrosion resistance. They are compatible with Swagelok®, Let-Lok, and A-Lok fittings.
For technical drawings and 3-D models, click on a part number.
Caps for tubing have a nut and a sleeve so you can close off the end of your tubing in place of a fitting. Caps for fittings replace the nut and sleeve of an existing fitting.
| For Tube OD | Nut Material | Max. Pressure | Each | |
| 3/4" | Brass | 700 psi @ 72° F | 00000000 | 00000 |
| For Tube OD | Sleeve Material | Front Sleeve Lg. | Back Sleeve Lg. | Max. Pressure | Each | |
| 3/4" | Brass | 19/64" | 5/32" | 700 psi @ 72° F | 00000000 | 00000 |
45° Flared Fittings for Copper and Brass Tubing
- Temperature Range: -65° to 250° F
- Tubing: Use with seamless brass and copper that meets ASTM B280
No sleeve is required to assemble these fittings, which makes for a faster, more convenient installation compared to 37° flared fittings. They require a nut (sold separately) for each tube end. Fittings are also known as refrigeration and SAE fittings. They are brass for good corrosion resistance.
Copper tube size is the accepted designation of the copper tubing industry, not the actual tube OD.
For technical drawings and 3-D models, click on a part number.
- For Use With: Air, Cutting Oil, Diesel Fuel, Fuel Oil, Mineral Oil, Refrigerant, Water
- Specifications Met: SAE J512, SAE J513, UL Listed
For Tube | |||||
|---|---|---|---|---|---|
| OD | Wall Thick. | Material | Max. Pressure | Each | |
| 3/4" | 0.035" | Brass | 550 psi @ 72° F | 000000000 | 000000 |
- For Use With: Air, Cutting Oil, Diesel Fuel, Fuel Oil, Mineral Oil, Refrigerant, Water; except nuts for 1" tube OD are not for use with fuel oil
- Specifications Met: SAE J512, SAE J513, UL Listed; except nuts for 1" tube OD meet SAE J512 and SAE J513 only
37° Flared Fittings for Steel Tubing
- For Use With: Air, Cutting Oil, Fuel Oil, Hydraulic Fluid, Mineral Oil
- Tubing: Use with seamless steel
- Specifications Met: SAE J514
Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on tubing that is flared to 37°. They require a nut and a sleeve (ferrule) for each tube end. Nuts and sleeves are sold separately. Fittings are zinc-plated steel for fair corrosion resistance.
For technical drawings and 3-D models, click on a part number.
30° Flared Fittings for Steel Tubing
- Specifications Met: See table
Also known as JIS (Japanese Industrial Standard) fittings, these have a 30° flare on one or both ends. Fittings are zinc-plated steel for fair corrosion resistance.
For technical drawings and 3-D models, click on a part number.
- Temperature Range: -65° to 500° F
| For Tube OD | Pipe Size | Material | Max. Pressure | Specifications Met | Each | |
| 3/4" | 5/8 | Zinc-Plated Steel | 4,000 psi @ 72° F | ISO 228-1, JIS B 0202, JIS B 8363 | 00000000 | 000000 |
- Temperature Range: -65° to 500° F
| For Tube OD | Pipe Size | Material | Max. Pressure | Specifications Met | Each | |
| 3/4" | 5/8 | Zinc-Plated Steel | 4,000 psi @ 72° F | ISO 228-1, JIS B 0202, JIS B 8363 | 00000000 | 000000 |
Yor-Lok Fittings for Steel Tubing
- For Use With: Air, Cutting Oil, Diesel Fuel, Fuel Oil, Gasoline, Hydraulic Fluid, Mineral Oil
- Tubing: Use with seamless steel
- Specifications Met: See table
A nut with two sleeves (ferrules) gives these fittings extra gripping power. The sleeves bite into tubing as you tighten the nut, creating a strong seal. Also known as instrumentation fittings, they are made to tight tolerances for use in high-precision applications. Fittings are zinc-plated steel for fair corrosion resistance. They are compatible with Swagelok®, Let-Lok, and A-Lok fittings.
For technical drawings and 3-D models, click on a part number.
Caps for fittings replace the nut and sleeve of an existing fitting.
For Tube | Caps For Fitting | ||||||
|---|---|---|---|---|---|---|---|
| OD | Wall Thick. | Material | Max. Pressure | Temp. Range, °F | Specifications Met | Each | |
| 3/4" | 0.049" | Zinc-Plated Steel | 2,200 psi @ 72° F | -20° to 395° | ASTM A108 | 00000000 | 000000 |
For Tube | |||||||
|---|---|---|---|---|---|---|---|
| OD | Wall Thick. | Nut Material | Max. Pressure | Temp. Range, °F | Specifications Met | Each | |
| 3/4" | 0.049" | Zinc-Plated Steel | 2,200 psi @ 72° F | -20° to 395° | ASTM A108 | 00000000 | 00000 |
For Tube | ||||||||
|---|---|---|---|---|---|---|---|---|
| OD | Wall Thick. | Front Sleeve Material | Back Sleeve Material | Max. Pressure | Temp. Range, °F | Specifications Met | Each | |
| 3/4" | 0.049" | Zinc-Plated Steel | 316 Stainless Steel | 2,150 psi @ 72° F | -20° to 800° | ASME B31.3 | 00000000 | 000000 |
Compression Fittings for Steel Tubing
- For Use With: Inch: Air, Hydraulic Fluid, Water
Metric: Hydraulic Fluid - Tubing: Inch: Use with welded steel
Metric: Use with seamless steel - Specifications Met: Inch: SAE J514
Metric: ISO 8434, DIN 2353
A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal. The nut and sleeve are included. Fittings are also known as flareless and bite fittings.
Zinc-plated steel fittings have fair corrosion resistance.
For technical drawings and 3-D models, click on a part number.
- Temperature Range: See table
For Tube | ||||||
|---|---|---|---|---|---|---|
| OD | Wall Thick. | Material | Max. Pressure | Temp. Range, °F | Each | |
| 3/4" | 0.065" | Zinc-Plated Steel | 2,000 psi @ 72° F | -65° to 400° | 000000000 | 000000 |
- Temperature Range: See table
| For Tube OD | Nut Material | Max. Pressure | Temp. Range, °F | Each | |
| 3/4" | Zinc-Plated Steel | 2,000 psi @ 72° F | -65° to 400° | 000000000 | 00000 |
- Temperature Range: See table
| For Tube OD | Sleeve Material | Max. Pressure | Temp. Range, °F | Each | |
| 3/4" | Zinc-Plated Steel | 2,000 psi @ 72° F | -65° to 400° | 000000000 | 00000 |
37° Flared Fittings for Aluminum Tubing
- For Use With: Air, Coolant, Gasoline, Hydraulic Fluid, Water
- Temperature Range: -60° to 400° F
- Tubing: Use with seamless aluminum
Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on tubing that is flared to 37°. Fittings are aluminum, which is lightweight with good corrosion resistance. They require a nut and a sleeve (ferrule) for each tube end. Nuts and sleeves are sold separately.
For technical drawings and 3-D models, click on a part number.
| For Tube OD | Material | Max. Pressure | Each | |
| 3/4" | Anodized 2024 Aluminum | 3,000 psi @ 72° F | 0000000 | 00000 |
| For Tube OD | Nut Material | Max. Pressure | Each | |
| 3/4" | Anodized 2024 Aluminum | 3,000 psi @ 72° F | 0000000 | 00000 |
| For Tube OD | Sleeve Material | Max. Pressure | Each | |
| 3/4" | Anodized 2024 Aluminum | 3,000 psi @ 72° F | 0000000 | 00000 |
Compression Fittings for Plastic Tubing—Chemicals
- For Use With: PFA Plastic: Hydrochloric Acid, Sulfuric Acid
PTFE Plastic: Alcohol, Ammonia, Benzoic Acid, Bleach, Bromine, Coolant, Fluoboric Acid, Hydrochloric Acid, Hydrofluoric Acid, Nitric Acid, Organic Solvents, Sodium Carbonate, Sulfuric Acid - Temperature Range: PFA Plastic: 0° to 350° F
PTFE Plastic: -40° to 185° F - Tubing: PFA Plastic: Use with hard (Durometer 50D-65D) PFA or PTFE plastic
PTFE Plastic: Use with hard (Durometer 60D) PFA or PTFE plastic
A sleeve (ferrule) compresses the tubing as you tighten the nut, creating a strong seal. The nut and sleeve are included. Fittings are also known as flareless fittings. Fittings that include a gripper sleeve on the tubing create an even tighter seal.
PFA fittings stand up to harsh substances. They’re made through a melting process.
For technical drawings and 3-D models, click on a part number.
| For Tube OD | Material | Color | Max. Pressure | Each | |
| 3/4" | PFA Plastic | White | 125 psi @ 72° F | 000000000 | 0000000 |