Sets include an assortment of keys. These simple tools turn fasteners from either end and reach into tight spots.

When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places.

These assorted keys have a retaining ring at the tip that grips inside the recess to ensure screws won’t fall off.

Often used to install carbide inserts in cutting tools, these keys have a small handle that prevents you from generating too much torque when turning a fastener.

These plastic organizers store keys in slots marked with the size.

Sets include assorted keys with long shafts that reach into tight spots. The plastic-covered handles provide a good grip for your whole hand.

Use the long shaft for more reach and the short shaft for more torque when turning fasteners.

The assorted keys in these sets have a small T-handle that prevents you from generating too much torque when turning a fastener. They are often used to install carbide inserts in cutting tools.

These assorted keys have a retaining ring on the tip that grips inside the recess to hold screws in place. Often used to install carbide inserts in cutting tools, these keys have a small T-handle that prevents you from generating too much torque when turning a fastener.

The toughest bits available, these withstand the shock and twisting force of impact drivers.

The six rounded points fit the star-shaped recess of Torx-Plus screws. These bits have a similar profile to Torx but are not recommended for use with standard Torx screws.

Less likely to crack or shatter under high torque than standard bits, these are often used with power tools to install machine screws.

When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.

The slightly tapered tip wedges into the screw recess for a secure hold. Also known as Torx-Align bits.

The six rounded points fit the star-shaped recess of Torx-Plus screws. These bits have a similar profile to Torx but are not recommended for use with standard Torx screws.

Bits have a different size at each end. An opening at the tips accommodates the pin in the recess of tamper-resistant Torx screws. These are also known as pin-in-Torx bits.

A ratchet mechanism turns fasteners more quickly than a standard bit driver. Insert a bit into the shaft and a magnet holds it in place.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet EN 60900 and IEC 60900.

Bits have a different tip at each end and snap into the shaft, which is also a nutdriver.

Press down on the handle’s collar to either adjust the shaft length or remove the shaft and replace it for a different tip. Sets include a handle and multiple reversible shafts.

Sets include an assortment of drivers with soft, contoured handles that provide comfort and the best possible grip for achieving maximum torque.

Sets include an assortment of drivers.

The assorted drivers in these sets have a ball end that allows angled entry to turn screws in hard-to-reach areas.

Sets include assorted drivers with an insulated handle and shaft that protect against shock from accidental contact with live electrical circuits. They are tested to 1,000 volts to meet IEC, EN, or ASTM standards.

Protect your stainless steel screws by using a stainless steel driver. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These drivers eliminate that risk.

Ensure carbide inserts are tightened to the correct torque. These tools are set to the recommended torque values for each screw size.

Press the rotating end cap on the handle with your palm to apply constant pressure while turning the body of the screwdriver with your fingertips.

Also known as ESD-safe screwdrivers, the handle drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment. Use the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC, EN, or ASTM standards. Use the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

These sockets are also known as pin-in-Torx bits.

In addition to a standard square drive, the sockets in these sets have a hex-shaped base so you can use a ratchet wrench along with an open-end or box wrench for additional leverage.