These slotted thumb screws have a thin, knurled head for use in low-clearance applications. Made of 18-8 stainless steel, they are chemical resistant.

A thin, knurled head allows these thumb screws to be used in low-clearance applications. They have a black-oxide finish to resist corrosion in dry environments.

Brass thumb screws are corrosion resistant in wet environments and electrically conductive.

These metric thumb screws are made of chemical-resistant 18-8 stainless steel. They have a raised head that makes them easy to grip.

These metric thumb screws have a raised head that makes them easy to grip. A black-oxide finish provides corrosion resistance in dry environments.

Stainless steel thumb screws have excellent corrosion resistance in most environments.

Brass thumb screws are corrosion resistant in wet environments and electrically conductive.

These slotted thumb screws are slim to fit in tight spaces.

Stainless steel thumb screws have excellent corrosion resistance in most environments.

These metric thumb screws have a knurled head for a slip-resistant controlled adjustment.

Tighten these thumb screws by hand or with a hex key for more torque.

These metric thumb screws have a large head that allows you to grip them with your entire hand for greater torque while tightening than standard knurled plastic-head thumb screws.

Stronger than standard nylon, these thumb screws are chemical resistant, nonconductive, and lightweight. They have a raised head that makes them easy to grip.

A thin head allows these thumb screws to be used in low-clearance applications.

Fasten material by hand, so tools don’t scratch or contaminate parts you frequently adjust in food-processing or pharmaceutical plants.

Stainless steel thumb screws have excellent corrosion resistance in most environments.

Wings provide more leverage than spade-head thumb screws for greater torque while tightening. A zinc plating provides corrosion resistance in wet environments.

These metric thumb screws are made of chemical-resistant 18-8 stainless steel. Also known as dog- and pilot-point thumb screws, insert the point into a drilled hole or slot to hold items in place.

Arms provide a flat surface to push your fingers against.

For maximum contact with angled and uneven surfaces, the tip swivels in all directions. The tip is narrow so it will fit through threaded holes.

A wide tip provides more gripping power than standard swivel-tip thumb screws. To use, remove the tip, thread the screw through the hole, and attach the tip on the other side.

These steel thumb screws have a black-oxide finish to resist corrosion in dry environments.

Snap these screws into panels up to 0.125" thick—no tools are required for installation.

Install these thumb-screw-head screws through a hole and thread on a retainer to keep secure—no special tools are required.

These wing-head screws have a clip-on nut that allows you to mount them near the edge of a thin panel. Use them to lock and release access panels, doors, and covers with a quarter-turn.

Press these wing head nuts into the backside of a panel in applications where you have access to both sides of the panel. A quarter-turn locks and releases access panels, doors, and covers.

Suitable for food-processing areas, these one-piece knobs have no joints to collect dirt or debris. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery. Mount them into a threaded hole.

A rubber coating provides a comfortable grip to position, tighten, and hold fixtures, equipment, and machinery. Mount these knobs into a threaded hole.

Install these knobs on a threaded stud. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

A rubber coating provides a comfortable grip to position, tighten, and hold fixtures, equipment, and machinery. Install these knobs on a threaded stud.

Long shafts can thread through these knobs for mounting versatility. The knobs provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

To build a custom knob or thumb screw, pair one of these knobs with a hex or socket head screw. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

Convert screws into knobs so large you can grip them with heavy work gloves. Slip these knobs onto a hex or socket head screw and tighten the set screw to secure. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

A handle makes these knobs easy to turn. Mill specific holes or keyways in the hub to meet your specifications, or weld in place. These knobs provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

Tap custom threads or secure with a set screw to provide a firm grip to position, tighten, and hold fixtures, equipment, and machinery.

A handle makes these knobs easy to turn. Tap custom threads or secure with a set screw to provide a firm grip to position, tighten, and hold fixtures, equipment, and machinery.

To build a custom precise-control knob or thumb screw, pair one of these knobs with a socket head screw. Turn the knob to move the screw 0.005" per graduation and make precise adjustments.