We will reply to your message within an hour.
Made of aluminum, these spacers are lightweight and mildly corrosion resistant.
18-8 stainless steel spacers have good corrosion resistance.
The zinc plating provides some corrosion resistance.
Brass makes these spacers electrically conductive and the zinc-plated finish adds corrosion resistance.
These spacers have excellent corrosion resistance and are passivated for enhanced protection.
The anodized coating on these lightweight spacers provides increased abrasion resistance over uncoated aluminum.
Withstanding salt water, acids, and chemicals, these spacers resist corrosion better than any other metal spacer we offer. They have a high strength-to-weight ratio and are about 40% lighter than steel spacers.
These spacers have excellent wear and abrasion resistance. Exposure to moisture may cause them to expand.
Almost nonabsorbent, these unthreaded LDPE and HDPE spacers won't swell when exposed to water.
Polypropylene spacers have a hard surface and resist many chemicals and solvents.
Use PEEK spacers as an alternative to metal spacers in high-temperature, high-stress applications. They resist chemicals, wear, and moisture.
Naturally slippery and wear resistant, acetal spacers also offer some resistance to moisture.
Made of FDA-listed material, these clear spacers can be used in food and beverage applications.
PTFE spacers have a slippery surface and surpass most plastic spacers when it comes to chemical resistance and performance in extreme temperatures.
Cut stock to the length you need.
Reduce vibration, shock, and noise with these spacers that compress between components.
Choose the OD, ID, length, and material and we will accommodate your unique spacer needs.
A nickel-chrome plating gives these spacers a mirror-like finish.
Protect components from electrical charges.
Create space to clean between components on food processing lines and other sanitary equipment.
An economical alternative to standard unthreaded spacers.
Also known as saddle washers, the curved end fits against round objects such as tube and pipe.
The 45° end fits against an angled surface to create a flat surface for connection.
Also known as arbor spacers, these are notched to space components on a keyed shaft.
Choose these standoffs for their adherence to NAS 1831 specifications.
A nickel-chrome plating gives these standoffs a mirror-like finish.
Mount components onto food processing lines, walls, and sanitary equipment while leaving space to clean in between.
A recess under the hex clinches a panel for a strong hold that won't push, pull, or twist out. When mounted with a lever press, the hex sits flush with the surface and the open end creates a through hole.
These standoffs are designed to fit in the limited space of compact electronics such as laptops and hand-held devices.
Also known as captive spacers, the splines on these bite into a panel for a permanent hold.
Designed for multi-level printed circuit board applications, these self-aligning, through-hole supports have a chamfered female end for stacking. The other end snaps and locks in place for a permanent connection.
Often called swage standoffs because you permanently crimp them into a panel.
Protect bolts from sideways (shear) pressure.
A zinc-plated finish gives these steel inserts mild corrosion resistance.
These aluminum inserts are lightweight, nonmagnetic, and mildly corrosion resistant.
Made from brass, these inserts are nonmagnetic, mildly corrosion resistant, and electrically conductive.
Have different sizes and lengths of spacers ready for a variety of jobs.
Run wires through the hollow stud of these nuts or use them as vents.
Push these nuts into place rather than threading them onto a fastener.
Quickly fasten threaded rod to strut channel. Snap these hinged nuts onto a threaded rod, then slip the head through a strut channel hole.
Connect two channels to create a stacked channel.
Serrated grooves grip the lip of the channel.
Keep a rod securely centered against the strut channel.
Also known as insert nuts, these convert slotted holes to threaded round holes and keep them centered in the channel.
Quickly attach these nuts by twisting them closed at any point along a threaded rod.
A spring plus serrated grooves that grip the lip of the channel provide a more secure hold than standard strut channel nuts.
Insert these nuts into the long open side of strut channel and twist to secure. A built-in washer enables one-handed installation.
A tab fits tightly against the lip of the channel to keep these nuts from slipping.
In addition to serrated grooves for gripping the lip of the channel, these nuts have wings for easy positioning.
There's no need for additional fasteners with these nuts—they combine a strut channel nut with a spring and a threaded stud.
Use with hex nuts to connect threaded rod.
Keep hardware centered in the strut channel slot.
Add hardware to strut channel without having to hold the washer in place or reach inside the channel.
Notches on these washers grip the channel to keep them in place.