Sized to cut oversized threads, these tools are often used to tap holes where the threads will shrink due to heat treatment or plating. They're made of high-speed steel and are for use on most metal and plastic. With a square shank, they're compatible with tap wrenches and tap holders for drill presses and milling machines. All have a plug chamfer with 3-5 chamfered cutting threads, so they're suitable for start-to-finish tapping. When using them to tap closed-end holes, be sure to leave sufficient space at the bottom for chips to accumulate.

For technical drawings and 3-D models, click on a part number.

Keep chips clear while tapping. Also known as gun taps, these have spiral-point flutes that push chips ahead of the tap and out of through holes. Because they don't need to be reversed to prevent buildup, they produce threads more efficiently than standard taps and are suitable for production work. They're made of high-speed steel for use on most metal and plastic. With a square shank, they're compatible with tap wrenches and tap holders for drill presses and milling machines. All have a plug chamfer with 3-5 chamfered cutting threads, so they're suitable for start-to-finish tapping.

Use uncoated taps for short production runs. Titanium-nitride (TiN) coated taps resist heat and wear better than uncoated taps, letting them last up to twice as long. Titanium-carbonitride (TiCN) coated taps have up to three times the tool life of uncoated taps. Their hard, smooth finish offers superior resistance to chipping, wear, and heat.

For technical drawings and 3-D models, click on a part number.

Clear chips while tapping deep and hard-to-reach holes. These taps have an extra-long shank for extended reach. Also known as gun taps, their spiral-point flutes push chips ahead of the tap and out of through holes. They don't need to be reversed to prevent buildup, so they produce threads more efficiently than standard taps and are suitable for production work. Their square shank is compatible with tap wrenches and tap holders for drill presses and milling machines. All have a plug chamfer with 3-5 chamfered cutting threads, so they're suitable for start-to-finish tapping.

Uncoated high-speed steel taps are for use on most metal and plastic.

For technical drawings and 3-D models, click on a part number.

Create oversized threads while keeping chips clear. These taps are sized for use in holes where the threads will shrink due to heat treatment or plating. Also known as gun taps, they have spiral-point flutes to push chips ahead of the tap and out of through holes. Because they don't need to be reversed to prevent buildup, they produce threads more efficiently than standard taps and are suitable for production work.

They're made of high-speed steel and are for use on most metal and plastic. With a square shank, they're compatible with tap wrenches and tap holders for drill presses and milling machines. All have a plug chamfer with 3-5 chamfered cutting threads, so they're suitable for start-to-finish tapping.

For technical drawings and 3-D models, click on a part number.

Insert these taps directly into drills, power screwdrivers, and other tools that accept a 1/4" hex shank. They're made of high-speed steel and are for use on most metal and plastic. All have a plug chamfer with 3-5 chamfered cutting threads, so they're suitable for start-to-finish tapping. When using them to tap closed-end holes, be sure to leave sufficient space at the bottom for chips to accumulate.

For technical drawings and 3-D models, click on a part number.

These taps are made of high-speed steel for higher strength and wear resistance than standard taps. Their flutes are designed to keep chips clear, so they don't need to be reversed to prevent buildup. With a square shank, they're compatible with tap wrenches and tap holders for drill presses and milling machines. Taps with plug chamfers have 3-5 chamfered cutting threads. Taps with bottoming chamfers have 1-2 threads.

Taps for through-hole threading have spiral-point flutes, which push chips ahead of the tap and out of through holes. They're also known as gun taps.

Taps for closed-end hole threading have right-hand spiral flutes. They draw chips back toward the tap while cutting threads to prevent chip accumulation in closed-end holes.

For technical drawings and 3-D models, click on a part number.

Coated with chromium carbide or titanium carbonitride (TiCN), these cobalt steel taps cut smoothly through soft material to produce accurate threads. Their square shank is compatible with tap wrenches and tap holders for drill presses and milling machines.

Taps for through-hole threading have left-hand spiral flutes to push chips ahead of the tap and out of through holes. All have a plug chamfer with 3-5 chamfered cutting threads, so they start threads with moderate torque and are good for start-to-finish tapping.

For technical drawings and 3-D models, click on a part number.

To tap nickel and other hard material, these cobalt steel taps have high cutting strength. Their spiral flutes keep chips clear, so they don't need to be reversed to prevent buildup. With a square shank, they're compatible with tap wrenches and tap holders for drill presses and milling machines. All have a plug chamfer with 3-5 chamfered cutting threads, so they're suitable for start-to-finish tapping.

Taps for through-hole threading push chips ahead of the tap and out of through holes.

Taps for closed-end hole threading draw chips back toward the tap while cutting threads, preventing chip accumulation in closed-end holes.

For technical drawings and 3-D models, click on a part number.

These taps are for use on most metal and plastic. They have a square shank that's compatible with tap wrenches and tap holders for drill presses and milling machines.

Use uncoated high-speed steel taps for small-scale tapping jobs. Titanium-nitride (TiN) coated high-speed steel taps resist heat and wear better than uncoated taps, letting them last up to twice as long.

Taper-chamfer taps have 7-10 chamfered threads at the tip for cutting into the workpiece. They require less torque than other chamfer types, making them a good choice for starting threads and tapping through holes. However, a longer taper means that they cannot thread as close to the bottom of closed-end holes.

Plug-chamfer taps are a versatile choice for most tapping applications. With 3-5 chamfered cutting threads, they require moderate torque and are often used for start-to-finish tapping of through holes and closed-end holes. However, they do not start threads as easily as taper chamfers. When using them to tap closed-end holes, be sure to leave sufficient space at the bottom for chips to accumulate.

Bottoming-chamfer taps cut into the workpiece with just 1-2 chamfered threads. This short chamfer lets them thread holes closer to the bottom than other taps, but they require more torque to start threads.

For technical drawings and 3-D models, click on a part number.