McMaster-Carr logo
    Filter by
    System of Measurement
    Thread Size
    Industrial Info Snippet
    Chamfer Type
    Number of Flutes
    Drill Bit Size
    Attribute Image
    Overall Length
    Attribute Image
    Thread Type
    Shank Type
    Thread Direction
    Thread Length
    Pitch Diameter Limit
    Attribute Image
    DFARS Specialty Metals
    For Hole Type
    For Threading
    U.S.–Mexico–Canada Agreement (USMCA) Qualifying
    Number of Tapping Ends
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Comments
    E-mail address (if you would like a response)
    8 Products

    Taps

    Image of Product. Front orientation. Taps. Taps.
    Cut threads into holes so screws, bolts, and rods fit snugly. Our basic taps have straight flutes that are good for most jobs.
    High-Speed Steel—The most versatile taps resist heat and wear to stay sharp. They’re good for most metals and plastic.
    Uncoated—The economical choice, these won't last as long as coated taps.
    Taper Chamfer—Good for both starting holes and threading through holes. These taps have the longest taper to gradually engage with the material, reducing the force needed to turn them. They can't reach the bottom of blind holes, however, so you will likely need to finish with a bottoming-chamfer tap.
    Plug Chamfer—These taps thread through holes and blind holes. The tapered section is shorter than a taper chamfer and longer than bottoming chamfer. As a result, they're easier to turn than bottoming taps but require more force than taper taps.
    Bottoming Chamfer—Cut all the way to the bottom of blind holes with taps that have the shortest taper. Since these require the most force to turn, they’re often used to finish holes started by taper- or plug-chamfer taps.
    Number of Flutes—Taps with fewer flutes have more space to capture chips, so you won’t have to clear them as often. However, they can be more difficult to keep straight in the hole.
    Taps Sold as Sets—Include one tap of each chamfer type.
    Taps
    Taps Sold as Sets
    Drill Bit
    Taper Chamfer
    Plug Chamfer
    Bottoming
    Chamfer
    Thread
    Size
    Thread
    Lg.
    Overall
    Lg.
    Thread
    Type
    No. of
    Flutes
    Size,
    mm
    Decimal Size
    Equiv.
    Shank
    Type
    Each
    Each
    Each
    No. of
    Taps
    Each
    High-Speed Steel
     
    Uncoated
    6-48
    11/16"2"UNS
    32.90.1142"Square000000000000000000000000000000000000000000300000000000000
     

    Chip-Clearing Taps

    Remove long, stringy chips to produce cleaner threads than standard taps. The flute design prevents buildup to protect the quality of the threads and avoid damage to the tap. Since you don’t need to reverse these taps to extract chips, they also form threads faster.
    High-Speed Steel
    Image of ProductInUse. Front orientation. Taps. Chip-Clearing Taps, Spiral-Point Flute for Through Holes.

    Spiral-Point Flute for Through Holes

    The most versatile taps resist heat and wear to stay sharp. They’re good for most metals and plastic.
    Uncoated—The economical choice, these won't last as long as coated taps.
    Titanium Nitride (TiN) Coated—Run at higher speeds and last twice as long as uncoated taps.
    Titanium Carbon Nitride (TiCN) Coated—Resist heat, chipping, and wear for three times the life of uncoated taps.
    Spiral-Point Flute for Through Holes—Push chips ahead of the tap and out of through holes. Also known as gun taps.
    Drill Bit
    Spiral-Point Flute
    for Through Holes
    Thread
    Size
    Thread
    Lg.
    Overall
    Lg.
    Thread
    Type
    Size,
    mm
    Decimal Size
    Equiv.
    Shank
    Type
    No. of
    Flutes
    Each
    Plug Chamfer
     
    Uncoated
    6-48
    11/16"2"UNS
    2.90.1142"Square200000000000000
     
    Titanium Nitride (TiN) Coated
    6-48
    45/64"2"UNS
    2.90.1142"Square20000000000000
     
    Titanium Carbon Nitride (TiCN) Coated
    6-48
    45/64"2"UNS
    2.90.1142"Square20000000000000
     

    Tap Sets

    These sets include a variety of taps for threading holes so screws, bolts, and rods fit snugly.
    High-Speed Steel—Single Thread Size Sets
    Image of Product. Taper, Plug, and Bottoming Chamfer Set. Front orientation. Taps. Tap Sets, Single Tap Thread Size.

    Taper, Plug, and Bottoming

    Chamfer Set

    The most versatile taps resist heat and wear to stay sharp. They’re good for most metals and plastic. These sets include one of each chamfer type: Taper for starting holes and threading through holes; plug for through holes and blind holes; and bottoming for cutting the closest to the bottom of any hole.
    Uncoated—The economical choice, these won't last as long as coated taps.
    Taper Chamfer, Plug
    Chamfer, Bottoming Chamfer
    No. of
    Pieces
    Tap Sizes
    Included
    Container
    Type
    No. of
    Flutes
    Shank
    Type
    Each
    Uncoated
    3UNS, 6-48Plastic Case3Square00000000000000
     
    Carbon Steel—Single Thread Size Sets
    Image of Product. Taper, Plug, and Bottoming Chamfer Set. Front orientation. Taps. Tap Sets, Single Tap Thread Size.

    Taper, Plug, and Bottoming

    Chamfer Set

    The economical choice for occasional hand tapping. These work on most metals and plastic but will dull more quickly than other taps. Sets include one each chamfer type: Taper for starting holes and through holes; plug for through holes and blind holes; and bottoming for cutting the closest to the bottom of any hole.
    Taper Chamfer, Plug
    Chamfer, Bottoming Chamfer
    No. of
    Pieces
    Tap Sizes
    Included
    Container
    Type
    No. of
    Flutes
    Shank
    Type
    Each
    Uncoated
    3UNS, 6-48Plastic Case3Square00000000000000
     
    back to top