McMaster-Carr logo
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Comments
    E-mail address (if you would like a response)
    13 Products

    Clamp-On Drill Bit Guides

    Image of Product. Front orientation. Drill Bit Guides. Clamp-On Drill Bit Guides.
    Drill precise holes without building a fixture. Clamp the jig onto your material and lift and turn the turret to select the hole size you need. Use the graduations to set the jig to the centerline of your workpiece.
    For Drill Bit Size
    For Drill Bit Size Decimal Equiv.
    Max. Opening
    Wd.
    Lg.
    Wd.
    Ht.
    Material
    Each
    3/16", 1/4", 5/16", 3/8", 7/16", 1/2"0.1875", 0.25", 0.3125", 0.375", 0.4375", 0.5"4"7 1/8"3 1/2"2 1/8"Steel, Nylon0000000000000

    Ball Guides for Flexible-Shaft Drill Bits

    Image of ProductInUse. Ball Guide with Drill Bit. Front orientation. Drill Bit Guides. Ball Guides for Flexible-Shaft Drill Bits.
    Image of Product. Ball Guides. Front orientation. Drill Bit Guides. Ball Guides for Flexible-Shaft Drill Bits.

    Ball

    Guide

    with

    Drill Bit

    Ball Guides

    Keep flexible-shaft drill bits centered between studs and drywall.
    For
    Drill Bit
    Shank
    Type
    Shank
    Size
    Shaft
    Size
    Material
    Dia.
    No. of
    Guides
    Each
    Round3/16"3/16"Plastic1 1/2", 2"2000000000000

    Thread-Forming Locknuts

    Form threads into these nuts for a tight fit that won't loosen under vibration. They are partially threaded, so when you fasten them onto metal screws, the tightening action will cut the rest of the threads. Nuts are reusable a handful of times, but the holding power decreases with each use.
    Plastic
    Image of Product. Bottom orientation. Locknuts. Thread-Forming Locknuts.
    Nylon 6/6—Slippery and abrasion resistant, these nuts thread on smoothly and stand up to daily wear and tear. Nylon will swell and weaken when exposed to moisture, so it's best for dry environments.
    Thread
    Size
    Wd.
    Ht.
    Pkg.
    Qty.
    Pkg.
    White Nylon 6/6
    2-56
    3/16"1/16"100000000000000000
    4-40
    1/4"3/32"10000000000000000
    6-32
    5/16"1/8"10000000000000000
    8-32
    21/64"1/8"10000000000000000
    10-24
    23/64"9/64"10000000000000000
    10-32
    23/64"9/64"10000000000000000
    1/4"-20
    27/64"15/64"10000000000000000
     

    Tap and Drill Bit Cases

    For Drill Bits
    Image of Product. Front orientation. Tap and Drill Bit Stands. Tap and Drill Bit Cases, For Drill Bits, Plastic.

    Plastic

    Store and organize drill bits so they stay in good working condition and don't go missing. These cases have individually marked holes for each size in your set.
    Plastic—Plastic cases have screw-on lids to block out moisture. Compared to steel cases, they're lighter, and they resist rust and dents. Clip them onto your belt to take with you on the job.
    For
    Drill Bit
    Overall
    Material
    No.
    of
    Size
    Dia.
    Ht.
    Features
    Each
    For Inch Drill Bits
     
    For Jobbers' Length
    Plastic291/16" to 1/2" (Increments of 1/64")3"6 5/8"Belt Clip0000000000000
     
    For Maintenance Length
    Plastic291/16" to 1/2" (Increments of 1/64")3 3/4"6 1/2"Belt Clip000000000000
     

    Tap and Drill Bit Stands

    For Taps and Drill Bits
    Image of Product. Front orientation. Tap and Drill Bit Stands. For Taps and Drill Bits.
    Keep taps and drill bits organized. All holes are labeled with sizes. Taps and drill bits are not included.
    Material
    No. of Taps
    Stored
    Holds Tap Sizes
    No. of Drill
    Bits Stored
    Holds Drill Bit Sizes
    Lg.
    Wd.
    Ht.
    Each
    Plastic16One each of M2, M3
    Two each of M4, M5, M6, M8, M10, M12, M14
    25Two each of 3.3 mm, 4.5 mm, 12 mm
    One each of 1.8 mm, 2.4 mm, 2.5 mm, 3.4 mm, 4.2 mm, 5 mm, 5.25 mm, 5.5 mm, 6.6 mm, 6.8 mm
    7 mm, 8.5 mm, 8.8 mm, 9 mm, 10.2 mm, 10.8 mm, 12.5 mm, 14 mm, 16 mm
    7"4 1/2"1 11/16"0000000000000
    Plastic26Two each of Nos. 2, 3, 4, 5, 6, 8, 10, 12
    Two each of 1/4", 5/16", 3/8", 7/16", 1/2"
    39Two each of 50 ga., 33 ga., 29 ga.
    One each of 47 ga., 45 ga., 44 ga., 43 ga., 42 ga., 39 ga.
    38 ga., 37 ga., 36 ga., 30 ga., 28 ga., 25 ga., 21 ga., 19 ga., 16 ga., 14 ga., 11 ga., 7 ga., 3 ga.
    One each of F, I, Q, U
    Two of 5/16"
    One each of 7/32", 1/4", 3/8", 25/64", 27/64", 7/16", 29/64", 1/2"
    7 3/8"4 11/16"1 11/16"000000000000
     
    back to top