We will reply to your message within an hour.
Change thread sizes or types, such as fine to coarse threads, on parts without changing gender.
In addition to joining male- and female-threaded parts, these adapters can increase or decrease metric thread sizes and change the thread pitch.
Change inch threads to metric with these adapters, or swap metric threads for inch. An external hex lets you tighten or loosen them with a wrench.
Connect male- and female-threaded parts of different thread types and sizes, while allowing air, liquids, wire, or other thin materials to pass through.
The through hole allows you to connect float rods to float valves.
Connect two differently sized male-threaded parts, such as threaded rods, and tighten with a standard wrench.
Increase or decrease metric thread size from one male-threaded part to another. Commonly used to connect two differently sized threaded rods, they have a hex-shaped body, so you can tighten them with a standard wrench.
Adapt threaded rods from inch to metric. These adapters connect two male-threaded fasteners, so you can change the gender of a mating part or increase or decrease its thread size. The hex-shaped body fits into the head of a standard wrench.
Often called sleeve nuts, these thread adapters fasten parts with right-hand threads to parts with left-hand threads.
Need to join two female-threaded parts, such as coupling nuts, with dissimilar inch thread sizes? Attach them to these adapters and tighten the exterior hex nut for a secure connection.
Twist these adapters onto female metric threads to change pitch or switch thread sizes.
One side inch, one side metric, and a hex in the middle—these handy fasteners connect two female-threaded parts, such as coupling nuts, adapting from inch threads to metric. Tighten with a standard wrench.
Join two female-threaded parts of various thread types and sizes, while allowing air, liquids, wire, or other thin materials to pass through.
Ridges keep these aluminum shims from sliding apart when stacked. Designed for aligning shafts and axles, they support heavier loads than plastic tapered shims.
Easily snap off any excess to get the length you need.
Ridges keep these shims from sliding apart when stacked.
The slot lets you install these rigid shims around screws.
Mount components onto food processing lines, walls, and sanitary equipment while leaving space to clean in between.
A hex drive on one end allows these rods to be turned with a hex key for ease of installation.
Install these bumpers with screws. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces.
All of these bumpers are reinforced with an embedded washer or base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines. Install them with screws.
Select these bumpers for applications that require specific load capacities. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Install them with a screw.
Keep bumpers of various shapes, materials, and mounting styles on hand to solve whatever problems arise.
Select these bumpers for applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Twist these bumpers into a threaded hole.
Twist these bumpers into a threaded hole. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces.
Press these bumpers into place with the adhesive backing. Use them as feet and spacers on instruments and small appliances to limit sliding, vibration, and noise. They're comparable to Bumpon bumpers.
Select these bumpers for applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Mount these bumpers on a threaded stud.
A ridge on the stem provides a tighter grip than other push-in bumpers. Push the stem into a hole for quick installation. These bumpers are commonly used as feet on instruments and bench-top equipment to keep them from sliding. They're also good as spacers between sheets of material. Also known as stem and grommet bumpers.
Use adapters on the ends of forcing screws and face-grip puller legs when pulling shafts, bearing caps, and pinions.
Convert drum openings with metric or BSPP threads to a 2 NPT pipe size.