Control multiple lights in the same footprint a standard light switch fits in.

For technical drawings and 3-D models, click on a part number.

Control lights by transmitting a wireless signal from these switches to a control relay (sold separately) on your fixture. Switches can be surface mounted with a wall plate or used as a hand-held remote. No batteries or secondary power source are needed.

Similar to a seesaw, these switches have an actuator that pivots when pressed to turn them on or off. They’re often used to control lighting, but they also work with AC motor loads up to 80% of the current rating. All fit standard wall plates (not included) and won’t stick out from your wall as much as toggle light switches.

Switches with spring-clamp terminals are quicker to install than those with screw terminals. Just push your bare wires into the connectors.

Illuminated switches glow when turned off, making them easy to spot in the dark.

Wall switch lockouts (sold separately) mount over switches to secure them in the on or off position.

For technical drawings and 3-D models, click on a part number.

Also known as three-way switches, these are often used in large, open workspaces and can be wired on opposite ends of the room to control lights on the same circuit. They work in pairs to control lights from two different locations. Actuate the switch by pressing on the wide, flat area. With a slim, low-profile design, they protrude less than toggle switches. All fit standard wall plates (not included).

Switches with spring-clamp terminals install quickly to create a secure connection. Just push a stripped wire into the clamp—no need to bend wire and screw it down.

Wall switch lockouts (sold separately) mount over switches to secure them in the on or off position.

Switch lights on and off no matter the forecast. NEMA 3R rated, these switches have a gasket that blocks out weather. They are rocker switches, so they protrude less off your wall than other switches.

Control multiple lights in the same footprint a standard light switch fits in. The low-profile design of these rocker switches protrudes less than other switches.

For technical drawings and 3-D models, click on a part number.

Prevent accidental activation—these switches require a key to turn lights on and off. They’re keyed alike, so all switches actuate with the same key. They also work with AC motor loads up to 80% of the current rating. All fit standard wall plates (not included).

For technical drawings and 3-D models, click on a part number.

Also known as three-way switches, these are often used in large, open workspaces and can be wired on opposite ends of the room to control lights on the same circuit. They work in pairs to control lights from two different locations. To prevent accidental activation, they require a key to turn lights on and off. They’re keyed alike, so all switches actuate with the same key. They also work with AC motor loads up to 80% of the current rating. All fit standard wall plates (not included).

For technical drawings and 3-D models, click on a part number.

Secure sensitive lighting equipment; these switches have a round key that is difficult to duplicate. The key is required to turn lights on and off. They’re keyed alike, so all switches actuate with the same key. They also work with AC motor loads up to 80% of the current rating.

Flat and completely smooth, these switches are easy to wipe down. They’re rated NEMA 3R, so they seal out water that could damage the circuitry. They also won’t corrode from mild cleaning solutions. With just a light tap, you can switch lights on and off, even if you’re wearing gloves.

Switches with a stainless steel wall plate resist wear and tear better than switches with a plastic wall plate.

Use these switches in place of standard wall switches to automatically turn electrical equipment on or off after a set interval of time. They’re often used with lights.

Switches with override can bypass the automatic shut-off.

Set switches with beep and light signals to alert when the timer is almost done; the signals can also be turned off.

Switches with set time recall retain the last setting; hold the button down to restart the timer with that setting.

For technical drawings and 3-D models, click on a part number.

Install these switches in a panel cutout. More precise than other time and day switches, they program on/off times for equipment down to the exact minute. The seven-day timing cycle can perform a different program each day of the week. All have an override to bypass the programmed on/off settings. A backup battery maintains the program during a power outage.

Mount these switches to a flat surface or attach to DIN rail. More precise than other time and day switches, they program on/off times for equipment down to the exact minute. All have an override to bypass the programmed on/off settings. A backup battery maintains the program during a power outage.

Seven-day switches can perform a different program each day of the week.

The circular pin terminals plug into relay sockets for easy installation. Also known as ice cube relays.

Relays rated for horsepower (hp) are built to handle tough, repetitive-use applications.

Relay sockets (sold separately) mount to 35 mm DIN rail (also known as DIN 3 rail) or can be mounted to a flat surface.

For technical drawings and 3-D models, click on a part number.

Send a signal to turn equipment on and off from up to 150 feet away without having to run electrical wire. These relays have an enclosure to protect the terminals from dust and accidental bumps. They can be set to transmit, receive, or both at once. You’ll need at least two relays to switch a device. They have an alarm that can be set to check for certain conditions before transmitting a signal. For example, you could set these relays to send a signal to turn on an air conditioner if all windows are closed. The repeat function extends the transmitting signal through a maximum of two receiving relays.

Relays that are set to transmit can be linked up to as many receiving relays as you need. Relays set to receive can be linked up to 30 transmitting relays. All relays connect to dry contacts on your switch, sensor, or controller. Use the wire leads to connect them to a power source.

UL and C-UL listed, all meet American and Canadian safety standards. Rated NEMA 1, they should only be used indoors.

For technical drawings and 3-D models, click on a part number.

A NEMA 4X enclosure protects these relays from washdowns, dirt, and corrosion. It also keeps terminals from being bumped accidentally, so you can mount these relays near working areas. Hardwire to your equipment with the wire leads.

For technical drawings and 3-D models, click on a part number.