With a smaller footprint than other switch mats, these fit in confined spaces.

Rated IP67 and NEMA 6, these switch mats withstand washdowns and temporary submersion. They have a smaller footprint than other switch mats to fit in confined spaces.

Customize the length of these switches by cutting them from a 25-foot roll. The width cannot be cut. They fit under carpeting or anywhere else you want to hide them. Mats have bare wires that solder or crimp to a connector.

These mats fit under carpeting or anywhere else you want to hide them.

Step on these mats to control doors, lights, or alarms.

Customize the length of these switches by cutting them from a 50-foot roll. They're narrow and thin, so they can be hidden under carpeting or installed anywhere space is limited. Actuate them anywhere along the length of the switch. A complete system includes a strip switch and a termination kit (sold separately).

Optional mounting channels secure switches to a flat surface.

Use surface fillers for vinyl fabric (not included) to seal ends.

For technical drawings and 3-D models, click on a part number.

These narrow switches are also thin enough to be hidden under carpeting or installed anywhere space is limited. Actuate them anywhere along the length of the switch.

Optional mounting channels secure switches to a flat surface.

For technical drawings and 3-D models, click on a part number.

Step or press anywhere along the switch to control doors, lights, or alarms. These switches are often placed across driveways and walkways to detect foot and vehicle traffic. Rated IP67, they can be temporarily submerged in puddles without the water harming their internal parts. These switches are bright yellow, so they can easily be spotted from far away. Made from PVC, they are flexible enough to conform to irregular and uneven surfaces.

For technical drawings and 3-D models, click on a part number.

Made with stainless steel conductors, these switches resist corrosion in damp areas. They’re less than 1/4” thick, so they’ll fit under floor mats and in other tight spaces. Control doors, lights, and alarms by pressing or stepping anywhere along the switch to actuate it. They’re more rigid than other strip switches, so mounting channels aren’t necessary—just stick them in place with mounting tape.

For technical drawings and 3-D models, click on a part number.

Prevent personnel from getting too close to dangerous equipment while it’s running. Step anywhere on these mats and they can turn on warning lights and alarms or shut down equipment. To minimize circuit damage, they also activate if they detect any malfunctions in your equipment’s electrical system. A complete switch requires a mat and a controller (sold separately). Together they meet ANSI/RIA R15.06 safety requirements. Mats are rated IP65 for protection from washdowns.

Red mats are easy to spot in crowded areas and in dim light. They help you avoid stepping on them if you don’t want to stop machinery or to find them quickly if you do.

Mats with diamond tread have a raised pattern on the surface to add traction and prevent slipping. Made from aluminum, they’re more durable than plastic mats, and less likely to be punctured or damaged by impact. However, they’re also more rigid than plastic mats, so they can only be used on flat surfaces. These mats are often used in high-traffic welding shops and freight warehouses.

Optional frames secure mats to the floor. Punch holes in the frame to insert a screw anywhere along the length.

For technical drawings and 3-D models, click on a part number.

Thicker than standard safety switch mats, these can withstand repeated impact from heavy and sharp objects. They turn equipment off when stepped on or when a fault is detected, preventing personnel from getting too close to dangerous equipment when equipment is on. A complete switch requires a mat and a controller (sold separately). Together they meet ANSI/RIA R15.06 safety requirements. Mats are rated IP65 for protection from washdowns.

Optional frames secure mats to the floor. Punch holes in the frame to insert a screw anywhere along the length.

For technical drawings and 3-D models, click on a part number.

Our most sensitive limit switches, these switches actuate with the slightest push for a high degree of accuracy. They’re often used for determining manufacturing tolerances and detecting minute expansions and contractions. When an object pushes into the plunger actuator, it sends a signal to open or close a circuit. Install them in a standard panel cutout.

IP67 rated switches are protected from temporary submersion. They’re ideal for wet locations.

For technical drawings and 3-D models, click on a part number.

Sensitive along their entire length, these switches are often used to signal when an overhead door closes or an item reaches the end of a conveyor. The sealed housing protects against exposure to weather.

Optional mounting channels (sold separately) secure switches to walls or conveyors.

For technical drawings and 3-D models, click on a part number.

Made of polycarbonate, these switches won't wear down even as objects constantly bump into them, unlike rubber bumper switches. They come in a sealed housing, so you don't need a mounting channel. Sensitive along their entire length, they're often used to signal when they've been hit by a cart or other rolling equipment.

For technical drawings and 3-D models, click on a part number.

Use these switches in place of standard wall switches to automatically turn electrical equipment on or off after a set interval of time. They’re often used with lights.

Switches with override can bypass the automatic shut-off.

Set switches with beep and light signals to alert when the timer is almost done; the signals can also be turned off.

Switches with set time recall retain the last setting; hold the button down to restart the timer with that setting.

For technical drawings and 3-D models, click on a part number.