Prevent accidental actuation—these toggle switches must be pulled up before they can switch a circuit.

A quick push is all it takes to actuate these switches.

Sized for 4 mm or 6 mm panel cutouts, these switches are often used with circuit boards to control electronics.

More durable than standard metal switches, these can handle tough, repetitive use.

Able to handle tough, repetitive use, these switches are more durable than standard plastic switches.

Immediately cut power with a single push.

Save space on a panel by using one switch to perform multiple switching functions.

Install in 12 mm dia. cutouts.

More lightweight than steel or stainless steel, these aluminum enclosed switches are rated NEMA 4X for protection from corrosion and washdowns.

Use these switches where ignitable gas and dust may be present. They're rated for use in hazardous locations.

These aluminum switches are rated NEMA 4, NEMA 13, and IP66 for protection from washdowns and oil/coolant spraying.

Immediately cut power with a single push.

Also known as high-inrush current switches, these switches can handle starting currents up to 10 times greater than their rating, such as when a motor starts.

Grip and twist a lever to turn these switches on or off—they’re designed to prevent accidental actuation. Install them into standard-sized panel cutouts.

Rated NEMA 4, 13, and IP66, these metal switches are protected from washdowns and oil/coolant spraying. Install them in 30 mm dia. cutouts.

The enclosure not only protects these switches, but also adds options for how you install them.

Choose an actuator and contact block to make your own 22 mm plastic switch.

Choose an actuator and contact block to make your own 22 mm metal switch.

Control machinery from a safe distance, or use these switches as call buttons.

Control cranes and other mobile machinery in dirty, outdoor, and wet environments without damaging your switch.

Install these key switches in 3/4" dia. panel cutouts. They require a key to turn circuits on or off, limiting access to sensitive equipment.

To prevent accidental actuation and limit access to sensitive equipment, these switches require a key to turn circuits on or off. The contact block and actuator are all one piece, so they won’t separate in high-vibration applications.

Designed for use near ignitable gases, fibers, and dust, these switches have a housing that seals in anything that could ignite flammable material. They require a key to turn circuits on or off, preventing accidental activation and limiting access.

Turn these switches by hand.

Immediately cut power by pulling the cable.

Connect these switches to a cable to control circuits from a distance. They're typically used to turn off production lines and material handling systems. Equipment will not start up again until switch is manually reset.

An infrared light beam senses the lightest finger contact to switch a circuit on or off.

Often used with machine guards, these switches mount to a door frame.

Often used in large, open workspaces, these switches can be wired on opposite ends of the room to control lights on the same circuit. They're also known as three-way and four-way switches.

No need for separate outlet boxes—these combine a switch and a receptacle into a single box.

Similar to a seesaw, these switches have an actuator that pivots when pressed to turn them on or off.

Combine a switch and receptacle into a single outlet box for a small footprint.

Control multiple lights in the same footprint a standard light switch fits in.

Prevent accidental activation—these switches require a key to turn lights on and off.

Secure sensitive lighting equipment; these switches have a round key that is difficult to duplicate.

Prevent unauthorized use—these switches require coded magnets to actuate. They cannot be bypassed using ordinary magnets.

Control two devices and delay the shut off of one device by up to one hour. These switches are often used with lights and fans for ventilation.

Push and release the button to activate—no electricity required.

The large face makes these switches easy to read from a distance.

Switches fit single device (1 gang) outlet boxes.

Program these switches to turn a device on and off at a set time and day.

When the microcontroller inside detects a power outage, these switches automatically fire up a backup generator. They’ll switch back to utility power once power is restored.

With no moving parts, these solid-state relays are fast switching and require less maintenance, last longer, and are quieter than mechanical switches.

Sealed for safety, these relays are a good choice for hazardous locations where combustible or corrosive gases may be present.