A rubber seal protects these switches from splashing water.

Maximize the space in a panel—these switches are half the size of most toggle switches.

Mount these switches under your desktop to keep your workspace clear and prevent accidental switching.

A quick push is all it takes to actuate these switches.

The built-in contact block in these switches extends behind the panel half the depth of most other 22 mm switches, saving valuable space.

Send a signal from your circuit board with the push of a button.

More durable than standard metal switches, these can handle tough, repetitive use.

The face of these switches mounts flush against a panel, so they're easy to clean and hard to damage.

Immediately cut power with a single push.

Because these switches mount flush against a panel, they're easy to clean and hard to damage.

Operate low-voltage devices that require less than 48 volts, such as doorbells and buzzers.

Actuate these switches with a quick push.

A lightweight yet durable alternative to stainless steel enclosed switches, these aluminum enclosed switches withstand corrosion, oil, and washdowns.

These familiar push-button switches mount to flat surfaces.

Snap these switches onto your T-slotted framing rails—no need to drill or disassemble your existing structure.

Grip and twist a lever to turn these switches on or off—they’re designed to prevent accidental actuation. Install them into standard-sized panel cutouts.

Rated NEMA 4, 13, and IP66, these metal switches are protected from washdowns and oil/coolant spraying. Install them in 30 mm dia. cutouts.

Made for areas where ignitable gas and vapor may be present, these switches have a housing that seals in anything that could spark flammable material.

The enclosure not only protects these switches, but also adds options for how you install them.

Choose from a variety of messages and colored lenses to combine a rocker with a base and wiring socket for a complete switch.

Also known as high-inrush current switches, these switches can handle starting currents up to 10 times greater than their rating, such as when a motor starts.

Rated IP67, these switches are protected from temporary submersion.

Choose an actuator and contact block to make your own 22 mm plastic switch.

Choose an actuator and contact block to make your own 16 mm switch.

Control machinery from a safe distance, or use these switches as call buttons.

Operate equipment from up to 330 feet away—these switches include a transmitter and a receiver that connects to equipment.

Apply pressure from any direction to actuate these switches.

Step on these switches for hands-free actuation in an area with frequent washdowns.

With a round key that is difficult to duplicate, these switches provide a higher degree of security than standard key switches.

To prevent accidental actuation and limit access to sensitive equipment, these switches require a key to turn circuits on or off. The contact block and actuator are all one piece, so they won’t separate in high-vibration applications.

Designed for use near ignitable gases, fibers, and dust, these switches have a housing that seals in anything that could ignite flammable material. They require a key to turn circuits on or off, preventing accidental activation and limiting access.

These 16 mm switches require a key to turn circuits on or off, limiting access to sensitive equipment.

Rated IP67 and NEMA 6, these switch mats withstand washdowns.

These mats fit under carpeting or anywhere else you want to hide them.

These narrow switches are also thin enough to be hidden under carpeting or installed anywhere space is limited.

Step or press anywhere along the switch to control doors, lights, or alarms.

Prevent personnel from getting too close to dangerous equipment while it’s running. Step anywhere on these mats and they can turn on warning lights and alarms or shut down equipment.

Open and close circuits in a snap—even in harsh conditions. With a rubber-encased housing and stainless steel bracket, these switches handle high vibrations and resist corrosion. They’re rated IP68 for protection from dust and temporary submersion.

Built for tight spaces exposed to water, these switches have a housing that's less than 1" long and IP67 rated for protection from temporary submersion.

Smaller than standard size snap-acting switches, these fit in tight spaces.

Sensitive along their entire length, these switches are often used to signal when an overhead door closes or an item reaches the end of a conveyor.

Made of polycarbonate, these switches won't wear down even as objects constantly bump into them, unlike rubber bumper switches.

With a smaller diameter and shorter length than standard sized switches, these fit in the most space-constrained areas.

Eliminate the need to calculate the sensing distance when using different metals—these switches sense all metal at the same distance. Also known as K=1 sensors.

The short body on these switches makes them suitable for tight spaces.

These inductive proximity switches sense metallic objects each time they pass through the slot, even when they’re obscured by water, oil, dirt, or a surface finish. Use them to measure the speed of rotating equipment and to count or detect moving objects, such as sheet metal being fed into a stamping process.

Detect aluminum cans, copper tubing, and other metal items that don’t contain iron.

Switches accept both AC and DC input voltage.

These switches have a longer sensing distance compared to other proximity switches with the same diameter.

Mount these flat inductive switches to a base or rail to remotely detect metallic objects in wet and dirty environments.

These switches use a NAMUR signal to operate at a low current and voltage, so they won’t ignite or produce sparks. ATEX certified, they protect against explosion in environments containing flammable gases and combustible dust. Switches sense both metallic and nonmetallic objects.

These switches detect magnetic objects—or objects with a magnet attached—through non-magnetic walls.

Wire contacts to an alarm system to alert when doors or windows are opened.

Control two devices and delay the shut off of one device by up to one hour. These switches are often used with lights and fans for ventilation.

With no moving parts, these solid state relays last longer, switch faster, and are quieter than mechanical relays. They interface between your controller and components to isolate input and output circuits, which protects components from voltage spikes, amplifies the relay’s signal, and reduces interference for reliable transmission.

Use these relays with industrial automation systems, security and emergency lighting, and small motors.

Often used for high-speed switching at low-current levels, these solid state relays have no moving parts, so they switch faster, last longer, and are quieter than mechanical switches.

For use with equipment that cycles on and off, these relays meet UL 508 for air conditioning and heating. Also known as definite-purpose contactors.

Sealed to keep out water, these relays are often used for DC-powered equipment such as forklifts, floor scrubbers, and trucks.

With no moving parts, these solid state relays require less maintenance and last longer, switch faster, and are quieter, than mechanical relays. Also known as automotive relays.

Often used to regulate the speed of AC fans or keep a heater at a set temperature, these relays connect directly to sensors to calculate and adjust output power. This allows you to use an analog input without converting it to a digital signal to control output power.

Considered solid state because they don’t have any moving parts, these timer relays last longer, switch faster, and are quieter than mechanical relays. They interface between your controller and components to isolate input and output circuits, preventing damage to your components from voltage spikes, amplifying the relay's signal, and reducing signal interference. They have multiple timing functions, so you don’t need to swap out your relay if you want to change their function.

For fast installation, mount these relays directly to 35 mm DIN rail (also known as DIN 3 rail). With no moving parts, these solid state relays last longer and require less maintenance, are quieter, and switch faster than mechanical relays.

The faceplate on these controllers is sealed to meet NEMA 4X and IP66 for protection in washdown environments with splashing water, corrosive liquid, and dust.

Built into an enclosure, these temperature controllers are protected when sitting on your workbench. They turn heating equipment on and off using a proportional-integral-derivative (PID) control algorithm to make fine adjustments, giving you the most precise and stable temperature control.

To protect equipment and personnel, these controllers shut down your machine when it gets too hot.

Since these switches don’t have a housing above the probe, they are often used in tight spaces and low-clearance areas.