We will reply to your message within an hour.
For a more secure connection than rail- and adhesive-mount clamps, weld the bottom plate of these clamps onto your rails. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.
Secure two pressurized hydraulic lines with a single clamp to lessen vibration in hydraulic systems. Weld the bottom plate onto the mounting surface for a more secure connection than rail- and adhesive-mount clamps.
Slide multiple clamps into existing strut channel to organize lines of pipe, tubing, and conduit without the need for drilling, welding, or using adhesive. Clamps have a plastic or rubber cushion or body to reduce vibration.
For use with a single line, these clamps mount directly onto rails, no adhesive or welding required. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.
Secure two pressurized hydraulic lines with a single clamp. Mount these clamps directly onto rails, no adhesive or welding required. They fit tightly around the lines to reduce vibration.
Bolt or weld these rails to the mounting surface, then attach clamps with a rail nut.
A rubber cushion reduces vibration and wear from clamp edges. The cushion also protects lines of pipe, tubing, and conduit from corrosion caused by metal-to-metal contact.
Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.
For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.
Mount parallel lines of pipe, tubing, or conduit directly against the mounting surface.
Route pipe, tubing, and conduit across strut channel.
For areas with low clearance, these clamps have the mounting fastener to the side of the material, rather than on top.
Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.
Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.
Hold pipe, tubing, and conduit away from strut channel.
A cushion covering the clamp reduces vibration and wear from clamp edges. Clamps surround lines of pipe, tubing, and conduit completely while holding them close to the mounting surface.
Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.
These clamps completely surround single lines of pipe, tubing, and conduit while holding them close to the mounting surface.
Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface.
Support vertical pipes passing through floors.
Use these clamps to route insulated pipe through floors. They have a plastic insert that creates a seal around the pipe's insulation to prevent the pipe from sweating, which can cause mold and corrosion.
Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.
Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.
Mount these hangers on top of one another to organize multiple lines of pipe, tubing, and conduit at any angle.
Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.
A roller on the bottom of these hangers compensates for movement due to expansion and contraction, such as in hydraulic applications. Combine with a threaded rod or other fastener to hang from the ceiling.
Access material quickly without uninstalling the mounted hanger. These hangers have a removable bolt for loading pipe, tube, and conduit from the side. Combine them with a threaded rod or other fastener to hang from the ceiling.
These hangers have a swivel nut for adjusting direction after mounting. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.
Also known as pipe shields, these cradles provide additional support and prevent insulation from tearing when routing insulated pipe through loop hangers.
Route multiple lines of pipe, tubing, and conduit with a single hanger. A wide opening and locking tab allow access for installation, adjustment, and removal.
For a strong, secure connection, mount these hangers by welding them to a rod.
Reduce movement in your line with hangers that are more rigid than strap hangers and fit tighter around pipe, conduit, and tube than loop hangers.
Use these close-fitting hangers for a more rigid hold around material than when using straps alone.
Cut as much strap as you need to hang duct, pipe, and other materials.
Mount these beams across parallel roof joists to hang threaded rod and route pipe, duct, and other overhead systems in areas where there’s no anchoring point.
Also known as muffler clamps, these U-bolts have a rounded mounting plate that fully surrounds pipe, conduit, and tubing for a secure fit.
Mount these general purpose U-bolts into an existing bracket, or combine with a mounting plate for a secure hold at the mounting surface.
A mounting plate provides a more secure hold at the mounting surface.
Add a mounting plate to your U-bolt for a more secure hold at the mounting surface.
Reduce vibration and noise in your lines—a plastic cushion tightly grips pipe, tubing, and conduit to prevent movement. Nylon-insert locknuts grip the thread to resist loosening.
Suspend and route flat-bottomed objects such as strut channel and small duct.
A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to disassemble it.
Reduce vibration and prevent metal-to-metal corrosion on flat-bottomed objects such as strut channel and small duct.
For a secure hold on pipe and conduit suspended above the ground, these supports have a cushioned clamp provides a 360° grip while reducing vibration.
Reduce noise caused by HVAC systems. These sturdy rubber supports isolate vibration caused by heat pumps and air conditioning units, resulting in a quieter facility. When used on roofs, they also keep components above puddled water, which can cause damage.
These U-shaped supports allows access to pipe and conduit after installation.
Adjust supports to the exact height you need to route pipe, conduit, and tubing through strut-mount routing clamps and hangers.
Bolt directly to a pipe flange to suspend a run of pipe above the ground.
Support lines that expand and contract. The roller on these supports compensates for movement in your line from changing temperatures.
Suspend material at any angle from the beam. Clamps have a fixed jaw that secures to the beam and a hanger that swivels 360° to position material and accommodate for misalignment.
Support strut channel at a right angle to the beam.
Route bundles of wire and cable through a single hook. A wide opening allows access for installation, adjustment, and removal.
Attach these supports onto metal stud knockouts to route cable, conduit, and tubing through metal studs.
Mount these brackets between two studs to support copper tubing for sink faucets and other water supply fixtures.
Combine with a U-bolt or routing clamp to convey a variety of material, such as pipe, tubing, and cable raceway, at distance from floors, walls, and ceilings. The extra clearance allows access for maintenance and adding and removing lines.
These OSHPD preapproved anchors and brackets support threaded-rod-mount hangers during seismic activity.
Mount to a surface to secure and route cable.
One clamp fits a wide range of diameters, so you can always have the right size on hand.
Not as bulky as our other constant-tension clamps, these round-wire clamps easily fit in cramped spaces. Use in low-pressure applications.
These clamps have a wider band than other constant-tension clamps, which provides more coverage and reduces the chance of leaks.
These clamps are easier to install than worm-drive clamps—crimp the pinch points with pinch-clamp pincers for a secure hold. They are also known as ear clamps.
These pinch clamps come packed in a box with individual compartments for each clamp size. Easier to install than worm-drive clamps, crimp the pinch points with pinch-clamp pincers for a secure hold. They’re commonly known as ear clamps.
A double ring of thick wire provides a complete seal around large-diameter hose.
These clamps are easier to install than our Extra-Strength Low-Profile Band Clamps. Also known as center-punch clamps, they seal with a quick hammer blow to the buckle.
The end of the band curls back into the buckle—this gives these clamps up to 25% more strength than other low-profile clamps. They are also known as JS-style clamps.
Designed for both permanent connections and emergency repairs, use these buckles with banding to create your own low-profile hose clamps.
Keep this banding on hand for both permanent connections and emergency repairs. You'll need an installation tool and a buckle (both sold separately) to create a band clamp.
Made of our most corrosion resistant stainless steel, these worm-drive clamps stand up to harsh acids and chemicals. Their band is smooth and has rolled edges, so they won’t cut into your hose or tube.
Clamps come packed in a box with individual compartments for each clamp size. To make sure they won’t cut into hose and tube, they have a smooth band with rolled edges.
The bolt design provides high strength and creates a 360° seal to prevent leaks.
Unlike other duct hose clamps, these are rated for a maximum work load. Clamps have a quick-release latch that lets you access your line frequently while maintaining your original clamp size.
Flip the toggle latch to install and remove these clamps in seconds.
The smooth finish inside these stainless steel quick-clamp fittings makes it easy to remove product residue.
Polished to a 20 Ra finish, these fittings have an extra-smooth interior that prevents product buildup and inhibits bacteria growth.
Butt-weld fittings allow for a smooth, flush connection that provides maximum flow.
Repair pinholes, punctures, and cracks in low-pressure systems with these clamps. Insert tubing into the clamp and tighten the bolts to create a secure seal.
Sized to fit snugly around pipe, these collars are often used to support pipe passing through floors and walls.
To avoid gouging and marring your pipe while making adjustments, these collars have flats where you can grab and rotate the pipe with a wrench. They're sized precisely for a tight fit around pipe, so they're often used to support pipe passing through floors and walls.
Sized to fit snugly around pipe, these collars have flats so you can turn the collar and your pipe using a standard wrench.
These connectors are for use in low-pressure air and vacuum conveying systems, as well as in gravity-flow systems.
Also known as no-hub couplings, these have a one-piece sleeve with a stop in the center, so you know your pipe is always aligned correctly.
To make installing and maintaining systems easy, these connectors come with clamps that form a strong seal on pipe and fittings once tightened.
Use these clamps to connect easy-access CPVC pipe fittings and pipe.
Connect these fittings to Schedule 40 plastic pipe—they are the industry standard for residential and commercial low-pressure plumbing and water supply applications. They are plastic for good corrosion resistance.
Connect these fittings to thick-wall plastic pipe—they have thicker, stronger walls than standard-wall fittings, so they can handle heavy duty industrial plumbing and water supply applications, such as water processing, waste water treatment, and irrigation. They can withstand pressures up to 900 psi.
Use with interlocking-clamp hose fittings to replace a damaged clamp. They consist of two halves held together by nuts and bolts.
Fittings come in two pieces to wrap around rails, so you can quickly modify existing structures without disassembling. Use clamp-on framing and fittings to form temporary partitions, modular conveyors, and workstations.
Attach sensors, tubes, and other components to T-slotted framing rails and structures.
Stay organized with hooks, bin boxes, shelves, and tool holders that work with T-slotted framing.
For compatibility with quick-connect clamps to secure pipe and conduit without screws and tools, this strut channel has narrow slotted holes.
Mount a length of strut channel between the ends of a beam to run cable and conduit along the beam without drilling.
These valves press down on the outside of tubing to adjust flow without contacting the process media.