The toughest bits available, these withstand the shock and twisting force of impact drivers.

When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.

Protect your stainless steel screws by using a stainless steel bit. If steel flakes off a standard bit and into the recess, it can lead to rust and contamination. These bits eliminate that risk.

An opening at the tip accommodates the pin in the recess of tamper-resistant Torx screws. These are also known as pin-in-Torx bits.

The six rounded points fit the star-shaped recess of Torx-Plus screws. These bits have a similar profile to Torx but are not recommended for use with standard Torx screws.

The toughest bits available, these withstand the shock and twisting force of impact drivers.

Ribs forged into the wings of these bits grip the screw recess to reduce stripping. They're also known as ACR® bits.

Protect your stainless steel screws by using a stainless steel bit. If steel flakes off a standard bit and into the recess, it can lead to rust and contamination. These bits eliminate that risk.

Remove screws in hard-to-reach places. A spring-loaded sleeve guides bits onto the screw head and keeps them from slipping out.

Thread these bits directly into your driving tool for minimal wobble in assembly applications.

An opening at the tip accommodates the pin in the recess of tamper-resistant pentalobe and tamper-resistant Torx Plus screws.

While screws with a Square/Phillips combination drive can be turned with either a Square or Phillips bit, these make the best contact so you can apply high torque without slipping and stripping the recess. They are also known as Quadrex bits.

Turn the screws found in Apple devices.

Turn two drive styles with one reversible bit. Remove and replace to change the tip.

The toughest bits available, these withstand the shock and twisting force of impact drivers.

Less likely to crack or shatter under high torque than standard bits, these are often used with power tools to install machine screws.

The slightly tapered tip wedges into the screw recess for a secure hold. These are also known as Torx-Align bits.

An opening at the tip accommodates the pin in the recess of tamper-resistant Torx screws. These are also known as pin-in-Torx bits.

Sets include an assortment of drivers with soft, contoured handles that provide comfort and the best possible grip for achieving maximum torque.

These standard-length drivers are found in every tool box.

A scaled-down version of standard screwdrivers, these tools are shorter, slimmer, and easy to take with you.

A cushioned grip over a plastic core adds comfort and some slip resistance.

Sets include an assortment of drivers with a cushioned grip that provides comfort and some slip resistance.

Sets include an assortment of drivers with a suede-like textured handle that provides a firm grip, even for oily hands.

The assorted drivers in these sets have a ball end that allows angled entry to turn screws in hard-to-reach areas.

A holding mechanism at the tip of the tool ensures the screw won’t slip off.

The tips of these assorted drivers have ribbed grooves that grip the surface of the recess to reduce slipping and minimizing the pressure required to achieve maximum torque.

Bright-colored handles make these tools stand out so they're less likely to be misplaced.

A shaft that extends through the handle and a steel end cap gives these drivers the strength to absorb hammer blows.

Sets include an assortment of drivers with a ring that can be secured with a lanyard to prevent drops. The ring rotates around the shaft so the driver turns freely.

Use the stud on the handle to bend and loop solid wire for making connections to outlets and switches.

Sets include assorted drivers with an insulated handle and shaft that protect against shock from accidental contact with live electrical circuits. They are tested to 1,000 volts to meet IEC, EN, or ASTM standards.

Sets include an assortment of stainless steel drivers, which protect stainless steel screws. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These drivers eliminate that risk.

These assorted screwdrivers are made of beryllium copper that is FM approved. They help meet OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

The handle on these assorted drivers drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment. They're also known as ESD-safe screwdrivers.

Lock the bit into the chuck to prevent accidental disengagement.

A ratchet mechanism turns fasteners more quickly than a standard bit driver. Insert a bit into the shaft and a magnet holds it in place.

Drive screws four times faster than ratcheting alone. Grip the speed housing at the base of the shaft with one hand while turning the handle with the other. A magnet at the end of the shaft holds bits in place.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet EN 60900 and IEC 60900.

When working in tight spaces, these short drivers fit where others can't. Bits have a different tip at each end and snap into the shaft, which is also a nutdriver.

Press down on the handle’s collar to either adjust the shaft length or remove the shaft and replace it for a different tip. Sets include a handle and multiple reversible shafts.

Sets include an assortment of drivers with a rotating end cap on the handle that allows you to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

The tip can be replaced when it becomes worn. These tools have a rotating end cap on the handle that allows you to apply constant pressure with your palm while turning the body of the driver with your fingertips.

A magnetized tip holds the screw in place. Press the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Also known as ESD-safe screwdrivers, the handle drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment. Use the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC, EN, or ASTM standards. Use the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Sets include an assortment of keys. These simple tools turn fasteners from either end and reach into tight spots.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t. Use to turn screws in hard-to-reach spots.

A retaining ring at the tip grips inside the recess to ensure screws won’t fall off.

Often used to install carbide inserts in cutting tools, these keys have a small handle that prevents you from generating too much torque when turning a fastener.

A ratchet mechanism turns fasteners more quickly than a standard driver. These screwdrivers have 90° offset tips to provide additional clearance when reaching over obstructions to turn fasteners.

These plastic organizers store keys in slots marked with the size.

Sets include assorted keys with long shafts that reach into tight spots. The plastic-covered handles provide a good grip for your whole hand.

The assorted keys in these sets have a long shaft for more reach and a short shaft for more torque when turning fasteners.

The assorted keys in these sets have a small T-handle that prevents you from generating too much torque when turning a fastener. They are often used to install carbide inserts in cutting tools.

A retaining ring on the tip grips inside the recess to hold screws in place. Often used to install carbide inserts in cutting tools, these keys have a small T-handle that prevents you from generating too much torque when turning a fastener.

Set includes a handle and six shafts. Remove and replace the shaft to use a different size or drive style.

Choose a handle based on torque and change shafts to use a different size or drive style. Factory-set screwdrivers ensure you reach the same torque every time.

These assorted screw starters have a slim body that reaches into tight spots to grip and turn screws that are hard to reach or too small to hold by hand.

Extra-long bits allow access to hard-to-reach fasteners.

These sockets are also known as pin-in-Torx bits.

The short Phillips bit on these sockets fits in spaces that screwdrivers can’t and where height clearance is limited.

Designed to fit on external Torx-Plus fasteners, often found on pickup trucks, these sockets have squared lobes that resist slipping at high torque.

Extra-long bits allow access to hard-to-reach fasteners.

With squared lobes that won’t slip at high torque, all of the sockets in these sets are designed to fit on external Torx-Plus fasteners, often found on pickup trucks.

These sockets are made to withstand the high torque and force of impact tools.

A ratchet mechanism allows you to turn fasteners in tight spaces without removing and repositioning the wrench.