Quickly position these sockets on square and external 8-point fasteners.

The hex shape achieves the best possible grip on hex fasteners to prevent rounding their points.

Eliminate the risk of your socket falling while reaching into your workspace with these flex sockets that have an integrated extension.

These short sockets fit spaces where height clearance is limited.

With more than double the clearance of standard sockets, these sockets access nuts on extra-long bolts.

Slide the open side of these sockets over a tube or hose to adjust a nut that’s already installed.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet IEC 60900.

The rounded-corner shape fits over ball joints commonly found in suspension and steering systems in vehicles.

For easy tightening and loosening, these sockets have pins that grip the slotted sides on bearing nuts.

Grip the indentations around the outside of tri-groove fasteners.

Tighten and loosen fasteners with an external Torx drive.

The short bit on these sockets fits in spaces where height clearance is limited.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet ASTM F1505 and IEC 60900.

Extra-long bits allow access to hard-to-reach fasteners.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

An extra-long Phillips bit allows these sockets to reach far-away fasteners. Use them where standard or stubby sockets can’t reach.

These sockets are also known as pin-in-Torx bits.

An opening at the tip of these sockets fits around the security pin, allowing you to drive tamper-resistant Torx Plus screws.

Attach one of these heads to your square-drive ratchet or torque wrench to extend its reach or to access spaces with limited vertical clearance.

Pivot the head to access fasteners from an angle.

Quickly position these sockets on square fasteners.

Extra length allows access to fasteners on long bolts.

With a smaller OD than standard sockets, these fit between tightly spaced fasteners.

Extra length allows access to fasteners on long bolts.

Achieve the best possible grip on hex fasteners and prevent rounding.

Move from lug nut to lug nut with the speed of a racecar pit crew. Up to five standard 6-point lug nuts stack up in the shank of these sockets, so you don’t have to stop to take the lug nuts out of the socket.

The slotted shape of these sockets fits over wing nuts to tighten and loosen them with more force than you can by hand.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Extra-long bits help you access hard-to-reach fasteners.

These sockets fasten Torx screws often used in vehicles, bicycles, and electronics.

The short bit on these sockets fits in spaces where height clearance is limited.

These sockets are designed to tolerate continuous use with power tools and impact tools in high-volume production and assembly.

Extend the shaft for additional length.

A rubber coating provides a comfortable grip.

The handle is covered in rubber for a comfortable grip.

Twist the grip to rapidly turn a socket before final tightening or to remove a fastener once loosened. The handle also swings like a traditional ratchet wrench.

No need to pull the socket off the tool—push a button to release.

Also known as a construction or spud handle, wrenches use the pointed end to align bolt holes.

Made of aluminum-bronze, these wrenches satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Rather than teeth, these wrenches use a series of rollers to engage the ratchet, enabling work in the tightest of spaces. Also known as silent ratchets, they don't make the traditional click sound when turned.

The 20° offset head provides clearance when reaching over obstructions.

No need to pull the socket off the tool—push a button to release.

The ratcheting mechanism turns sockets quickly.

Made of beryllium copper, these wrenches satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Pivot the head to access fasteners in tight spots.

Unlike most torque wrenches, you don’t have to return the torque setting to the lowest value after use. These tools are also known as split-beam torque wrenches.

Turn sockets from above when there's not room to swing a standard wrench handle.

A main pointer on the dial shows torque as it’s being applied and a memory pointer indicates the maximum torque reached.

Trust the precision of your measurements—these wrenches are accurate to ±2%.

Trust the precision of your measurements—these wrenches are accurate to ±1%.

These wrenches have an accuracy of ±2.0%.

Built for durability, these high-performance tools handle the demands of high-volume production and tough maintenance applications.

These tools are suitable for general shop, maintenance, and automotive work.

Use these wrenches for medium-volume production, general maintenance, and construction applications.

Convert from one square drive size to another.

Turn square-drive fasteners in several sizes with these socket sets.

Use one socket to switch between two fastener sizes.

Carry fewer impact sockets—these five reversible impact sockets turn 10 fastener sizes. Flip the socket around to turn a different size.

The hex shape grips hex fasteners and prevents rounding. These sockets are made to withstand the high torque and force of impact tools.

The hole in the middle of these bits fits the security pin in tamper-resistant Torx screws.

Extra-long bits help you access hard-to-reach fasteners.

When vertical space is tight or you need an extra twist on your socket, use one of the dual-drive Phillips bit sockets in this set.

Keep a convenient variety of drive styles and sizes of bit sockets on hand.

Extra-long bits allow access to hard-to-reach fasteners.

Tighten or loosen hard-to-reach fasteners with the extra-long bits in these socket sets.

The short bit on these sockets fits in spaces where height clearance is limited.

A spring-loaded ball on the bit holds fasteners in place as you drive them, including nonmagnetic fasteners like stainless steel screws.

Get a strong grip in tight areas, even on fasteners that are rounded or damaged.

Grip more of your fastener head with these wrench heads.

Shaped and sized for compatibility with wheel bearing locknuts on trucks and trailers, the sockets in these sets make it easy to install and remove locknuts.

With twice as many corners, 8-point sockets grab onto square-drive screws and nuts more quickly than 4-point sockets.

Grip the indentations around the outside of tri-groove fasteners.

The sockets in these sets have a cutout and extra length so you can reach and twist nuts without having to disconnect your line.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

With more than double the clearance of standard sockets, the sockets in these sets access nuts on extra-long bolts.

Suitable for occasional maintenance work, these sets are imported.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.