Convert from one square drive size to another.

These adapters are insulated to protect against accidental contact with live electrical circuits. They are tested to 1,000 volts to meet IEC 60900.

Turn sockets with a bit screwdriver.

Insulated to protect against accidental contact with live electrical circuits, these adapters are tested to 1,000 volts to meet IEC 60900 and ASTM F1505 standards.

Fit these adapters between a wrench and socket to enable finger tightening.

Convert your socket into a flex socket to access fasteners from an angle.

Change a standard wrench handle into a ratcheting wrench.

Keep common extension lengths on hand to reach a variety of spots—just attach them to your socket.

Bend these extensions to reach inconveniently located fasteners. These sets include multiple extension lengths, so you can find the right length to reach around obstructions.

Safely extend your reach in areas where you could accidentally come into contact with live circuits.

The male ends of these extensions are rounded, so they can pivot to use your tool at an angle.

Lock your socket into these extensions to prevent accidental disengagement.

A digital display shows how torque measurements change as you turn the wrench. Set the desired torque and angle—lights and an audible alarm indicate when target has been reached or exceeded.

Already set to a specific torque limit, these adapters audibly click and release when you reach that setting to prevent overtightening.

Convert from one square drive size to another.

Attach to your socket for a longer reach.

Attach one of these extensions to your impact socket to turn fasteners in hard-to-reach spaces.

Attach your impact square-drive sockets to power drills, impact drivers, and other tools that accept a hex shank.

Convert your impact socket into a flex socket to access fasteners from an angle.

Also known as positive-locking extensions, these extensions hold sockets place with a ball that only retracts when you pull the collar down. Designed to prevent accidental detachment, they lock to your socket more securely than other extensions.

Prevent overtightening that can damage fasteners. These adapters spring back slightly when the set torque is reached.

These adapters, which convert from one square drive size to another, were designed to tolerate continuous use with impact tools in high-volume production and assembly.

Use these adapters to connect sockets to impact wrenches and other power tools—they’re designed to tolerate continuous use in high-volume production and assembly.

A ratchet mechanism allows you to turn fasteners without removing and repositioning the wrench.

No need to pull the socket off the tool—push a button to release.

Pair these wrenches with a bolt-through socket to reach nuts at the bottom of a long threaded rod or bolt which can pass through the head of the wrench.

A gasket seals in permanent lubrication and keeps out dirt, dust, and moisture.

The shaft on these wrenches extends and locks.

Made of aluminum-bronze, these wrenches satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

The 20° offset head provides clearance when reaching over obstructions.

Turn sockets in the most confined spaces.

Use these tools for general shop applications.

Attach one of the heads in these sets to a torque wrench for more leverage to loosen a stubborn fastener.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Pair the sockets in these sets with the bolt-through ratchet wrench to reach nuts at the bottom of a long threaded rod or bolt.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Convert from one square drive size to another.

Carry fewer impact sockets—these five reversible impact sockets turn 10 fastener sizes. Flip the socket around to turn a different size.

The hex shape grips hex fasteners and prevents rounding. These sockets are made to withstand the high torque and force of impact tools.

Attach one of these heads to your square-drive ratchet or torque wrench to extend its reach or to access spaces with limited vertical clearance.

Switch out worn or damaged bits instead of replacing your entire bit socket.

These wrenches have one pivoting socket end and one open end.

Pivot the socket end to access hard-to-reach fasteners.

Designed to withstand high torque and force, these adapters fit the square drive on impact wrenches. Use with hex-shank bits (also known as insert bits).