We will reply to your message within an hour.
More
18-8 stainless steel screws have good chemical resistance.
More corrosion resistant than 18-8 stainless steel screws, these have excellent resistance to chemicals and salt water.
Stronger and more wear resistant than 18-8 and 316 stainless steel, these screws are mildly chemical resistant.
These steel screws are available with corrosion-resistant finishes.
One-third the weight of steel, aluminum screws resist corrosion in wet environments.
These steel screws are zinc plated to resist corrosion in wet environments.
Brass screws are corrosion resistant in wet environments and electrically conductive.
Made from 18-8 stainless steel, these screws are chemical resistant.
A Torx drive has more points of contact than Phillips, slotted, and square drives, allowing you to apply extra force with less slippage or damage to the recess.
A thick, decorative head provides a finished appearance.
A tamper-resistant Torx driver is required for installation and removal. Also known as pin-in-Torx, these screws allow you to apply extra force with less slippage or damage to the recess.
Also known as pin-in-hex, install and remove these screws with a tamper-resistant hex driver.
Install and remove these screws with a tamper-resistant spanner driver.
The S-shaped drive can be installed with a standard slotted driver, but requires a special tool for removal.
These screws require a Tri-Wing® driver for installation and removal.
A flange under the head distributes holding pressure and reduces the risk of crushing thin metal.
These square-drive screws have a flange under the head that distributes holding pressure and reduce the risk of crushing thin metal.
A free-rotating, permanently attached washer distributes holding pressure over a wider area than a flange and remains stationary to prevent scratching the material surface as you tighten the screw.
These square-drive screws are beveled under the head for use in countersunk holes.
These steel screws have a black-oxide finish to resist corrosion in dry environments.
Stronger and more wear resistant than 316 and 18-8 stainless steel, these screws are mildly chemical resistant.
These screws have a hex head for a secure grip with a wrench.
A rubber O-ring under the head creates a seal that withstands liquid and gas pressure.
Also known as Fastite screws, these offer more thread engagement in 0.028" to 0.063" thick sheets to prevent overtightening and damaging threads.
Able to penetrate overlapping sheets, these screws have a secure hold in wood.
Made from 410 stainless steel, these screws are strong, wear resistant, and mildly chemical resistant.
Serrations under the head act as a brake to prevent over tightening and damaging threads.
These steel screws have corrosion-resistant finishes.
410 stainless steel is strong, wear resistant, and mildly chemical resistant.
These 18-8 stainless steel screws have a hardened steel drill point to penetrate steel and are coated to increase corrosion resistance.
These screws have the strength of 410 stainless steel with added corrosion resistance.
Cutting their own pilot hole and threads as you fasten them into material, these metric screws have a drilling tip.
Stronger and more wear resistant than 18-8 stainless steel, these screws are mildly chemical resistant.
Drill a pilot hole, cut threads, and fasten in one motion with these metric-threaded screws. Made of steel, they’re strong and wear resistant.
By drilling their own holes and fastening in a single operation, these square-drive screws save time and effort. Made of 410 stainless steel, they're both stronger and more wear resistant than 18-8 stainless steel screws.
The extra-wide truss head distributes holding pressure to reduce the risk of crushing thin metal.
Also known as pancake head screws, these have a head that is about two-thirds the height of standard rounded head screws.
Made from stainless steel, these screws are more corrosion resistant than steel, and almost as strong.
These steel screws save you time and effort by drilling their own holes and fastening in a single operation.
With a drilling tip, these metric screws cut their own pilot hole and threads as you fasten them into material.
A decorative rounded top provides a finished appearance.
These steel screws are available with corrosion resistant finishes. A rubber-bonded washer compresses to form a watertight seal. They save you time and effort by drilling their own holes and fastening in a single operation.
These steel screws have a head encapsulated by 18-8 stainless steel.
Made from 18-8 stainless steel, these screws have good chemical resistance.
Known for their strength, these alloy steel screws are coated to provide corrosion resistance in wet environments.
Made from stainless steel to resist galvanic corrosion, use these screws to fasten aluminum to aluminum and steel framing. They save you time and effort by drilling their own holes and fastening in a single operation.
Beveled under the head for use in countersunk holes.
These screws have a free-rotating, permanently attached washer that remains stationary while tightening to prevent bunching while attaching tarps and other fabric to metal.
Serrations under the head act as a brake to prevent overtightening and damaging threads.
Also known as roofing screws, these screws are long and made from hardened steel to fasten rigid insulation board to steel decking.
These steel screws cut threads in drilled holes as they’re turned, so they require less driving torque and cause less stress on your material than thread forming screws.
A Torx drive has more points of contact than a Phillips drive, allowing you to apply extra force with less slippage or damage to the recess.
For a finished appearance that reduces the chance of snags on other material, these screws fit snugly in countersunk holes and have a domed head.
The green color identifies these as grounding screws. They have a flange that provides a wide flat surface for making solid electrical connections.
A wide cutting slot provides excellent chip clearing and low driving torque in soft metal.
Commonly used with door hinge hardware, these screws cut threads in material such as aluminum and brass.
Also known as Swageform screws, threads at the tip are designed to grab material for a fast start with low torque in a wide range of materials.
Also known as Tap-Flex screws, these are made from hardened steel to penetrate hard material. They have a five-edged shank that presses tightly against the material to form threads and resist loosening.
These screws speed installation by drilling, tapping, and fastening wood and metal in a single operation.
Thread-forming screws press threads into drilled holes for a tight vibration-resistant assembly.
Alternating high and low threads minimize driving torque and allow the screw to hold more material between threads for a stronger hold and better strip-resistance than standard drywall screws for wood.
Ribs under the head act as a brake to prevent over-tightening and damaging threads.
Power through drywall and into metal studs up to 0.105" thick.
Attach drywall to metal studs up to 0.036" thick.
A drill point powers through metal up to 0.105" thick.
Attach metal framing to metal studs up to 0.036" thick.
These square-drive screws have a drill point that powers through drywall and into metal studs up to 0.105" thick. Heads are one-third smaller than those of other drywall screws.
A drill point powers through drywall and into metal studs up to 0.105" thick. Heads are one-third smaller than those of other drywall screws.
With a square-drive head, these screws attach drywall to metal studs up to 0.036" thick. The head is one-third smaller than other drywall screws.
These screws have a head that's one-third smaller than other drywall screws. Use them to attach drywall to metal studs up to 0.036" thick.
Drill holes with the point on these hangers.
Fasten sheet metal up to 0.200" thick.
Drilling screws save you time and effort by drilling their own holes and fastening metal up to 0.500" thick in a single operation.