Adjustable-Width Sheet Metal Benders for Bench Vises
Shape sheet metal using your bench vise as a sturdy base. Remove or slide the four dies along the clamping bar to form angles, channels, boxes, trays, and pans in a variety of widths. Unlike bench-top and floor-mount benders, these are not permanently mounted—pull them out when you need them and store them when you don’t.
Base | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Max. Bending Wd. | For Max. Steel Thick. | For Jaw Wd. | Ht. | Wd. | Dp. | Max. Box Dp. | Frame Material | Ht. | Wd. | Dp. | Handle Grip Material | Includes | Each | |
For Aluminum, Copper, Stainless Steel, Steel | ||||||||||||||
| 12 1/2" | 1/16" | 4"-8" | 11" | 13" | 2" | 1" | Steel | 1" | 9 1/2" | 1/2" | Rubber | One 1" Wide Forming Die, One 2 7/8" Wide Forming Die, One 2" Wide Forming Die, One 5 7/8" Wide Forming Die | 0000000 | 0000000 |
Floor-Mount Adjustable-Width Sheet Metal Benders
Reinforced construction lets this bender handle thicker material than the bench-top model. Position the movable forming dies, also known as fingers, to make boxes, trays, and pans in different widths. An adjustable upper leaf and nose bar allow for radius bending.
Mounting Holes | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Max. Bending Wd. | For Max. Steel Thick. | Min. Reverse Bend | Ht. | Wd. | Dp. | Max. Box Dp. | Frame Material | Mounting Fasteners Included | No. of | Dia. | Includes | Each | |
For Aluminum, Stainless Steel, Steel | |||||||||||||
| 48 1/4" | 1/16" | 1/4" | 53" | 72" | 36" | 4" | Steel | No | 4 | 5/8" | Five 2" Wide Forming Dies Six 3" Wide Forming Dies Five 4" Wide Forming Dies Removable Apron Insert Apron Stop Rod Counterweights | 0000000 | 000000000 |
Bench-Top Adjustable-Width Sheet Metal Benders
Position the movable forming dies, also known as fingers, to make boxes, trays, and pans in different widths. An adjustable upper leaf and nose bar allow for radius bending.
Sheet Metal Bender | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Mounting Holes | Optional 26" Ht. Floor Stand | |||||||||||||||
| Max. Bending Wd. | For Max. Steel Thick. | Min. Reverse Bend | Ht. | Wd. | Dp. | Max. Box Dp. | Frame Material | Mounting Fasteners Included | No. of | Dia. | Handle Grip Material | Includes | Each | Each | ||
For Aluminum, Stainless Steel, Steel | ||||||||||||||||
| 48 1/4" | 3/64" | 1/4" | 25" | 65" | 22" | 4" | Steel | No | 4 | 1/2" | Plastic | Five 2" Wide Forming Dies Six 3" Wide Forming Dies Five 4" Wide Forming Dies Removable Apron Insert Apron Stop Rod Counterweights | 0000000 | 000000000 | 0000000 | 0000000 |
Economy Sheet Metal Benders
Make bends up to 90° in metal sheets to form items such as boxes and trays. Benders attach to your bench top and have a brake bar that adjusts for different stock thicknesses and bend angles.
Sheet Metal Benders
Make bends up to 135° in metal sheets. Benders have a clearance of 4" for insertion and removal of large workpieces such as vehicle panels and duct work. They attach to your bench top and have a removable front edge to make bends that are close together.
Sheet Metal Benders | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Max. Bending | Mounting Holes | Floor Stands | ||||||||||||
| Wd. | Angle | For Max. Steel Thick. | Ht. | Wd. | Dp. | Clearance | Frame Material | Mounting Fasteners Included | No. of | Dia. | Each | Each | ||
For Aluminum, Stainless Steel, Steel | ||||||||||||||
| 24" | 135° | 3/64" | 9" | 32" | 15" | 4" | Steel | No | 3 | 3/8" | 0000000 | 0000000 | 0000000 | 0000000 |
| 37" | 135° | 3/64" | 9" | 45" | 15" | 4" | Steel | No | 3 | 3/8" | 0000000 | 000000 | 0000000 | 000000 |
Combination Sheet Metal Shears, Benders, and Curvers
Save space in your shop by cutting, bending, and curving sheet metal with a single machine. Also known as shear brake rolls. Use the blade on the shear to make clean, straight cuts; it has two cutting edges for twice the life. A press brake makes bends up to 90°. Create curves and circles with the slip roll.
When using the shear or press brake, set the manual back gauge to precisely position the sheet metal for consistent cuts or bends.
Max. Bending | For Max. Thick. | Roller | Mounting Holes | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Wd. | Angle | Aluminum | Brass | Copper | Stainless Steel | Steel | Min. Bending Radius | Cut Lg. | Ht. | Wd. | Dp. | Dia. | No. of | Blade Material | Mounting Fasteners Included | No. of | Dia. | Each | |
For Aluminum, Brass, Copper, Stainless Steel, Steel | |||||||||||||||||||
| 12" | 90° | 1/32" | 1/32" | 1/32" | 1/64" | 1/32" | 3/4" | 12" | 15" | 14" | 11" | 1 1/2" | 3 | Steel | No | 4 | 0.32" | 0000000 | 0000000 |
| 30" | 90° | 3/64" | 1/32" | 1/32" | 1/64" | 1/32" | 3/4" | 30" | 23" | 32 1/2" | 14 1/2" | 1 1/2" | 3 | Steel | No | 4 | 0.32" | 0000000 | 00000000 |
| 40" | 90° | 3/64" | 1/32" | 1/32" | 1/64" | 1/32" | 7/8" | 40" | 23" | 42 1/2" | 14 1/2" | 1 5/8" | 3 | Steel | No | 4 | 0.32" | 0000000 | 00000000 |
Sheet Metal Curvers
Create bends, curves, and circles in sheet metal. Also known as slip rolls, these curvers can form a single curve. The rollers also have wire grooves to shape three sizes of wire. They mount to a table or bench top.
Roller | Mounting Holes | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Max. Bending Wd. | For Max. Steel Thick. | Min. Bending Radius | For Wire Dia. | Ht. | Wd. | Dp. | Material | Dia. | No. of | Frame Material | Mounting Fasteners Included | No. of | Dia. | Each | |
For Aluminum, Stainless Steel, Steel | |||||||||||||||
| 12" | 1/64" | 1/2" | 1/16", 1/8", 5/32" | 7" | 23" | 6" | Steel | 1" | 3 | Aluminum | No | 2 | 1/4" | 00000000 | 0000000 |
| 24" | 1/32" | 1" | 3/16", 1/4", 5/16" | 19" | 38" | 19" | Steel | 2" | 3 | Cast Iron | No | 4 | 3/8" | 0000000 | 00000000 |
| 36" | 1/32" | 1" | 3/16", 1/4", 5/16" | 19" | 51" | 19" | Steel | 2" | 3 | Cast Iron | No | 4 | 3/8" | 0000000 | 00000000 |
| 42" | 1/64" | 1" | 3/16", 1/4", 5/16" | 19" | 57" | 19" | Steel | 2" | 3 | Cast Iron | No | 4 | 3/8" | 0000000 | 00000000 |
Hand-Held Sheet Metal Benders for Making Corners
Fold corners in flat metal sheets to create your own bin boxes, drip pans, and other three-dimensional objects. Similar to tucking the corners of a bedsheet, these benders twist and wrap the metal into triangle-shaped folds to form corners. Finish the fold by creasing it with a regular hand-held sheet metal bender.
Style A benders have a longer throat depth for making deeper corners. They create corners in any angle.
Style B benders form precise 45° or 90° corners. They have a finger hole for additional gripping options.
Sheet Metal Curvers for Shrinking and Stretching Curves
Pull and pinch metal extrusions, such as L-channels, so they fit precisely around contoured edges and frames. These curvers shrink or compress curves as well as smooth ridges and dents without heating or welding.
Carry hand-held curvers along with you to jobs. They’re small enough to fit where floor-stand models can't.
Curvers with a stand have foot pedals to keep your hands free to move the metal and complete jobs faster than hand-held models. Mounted on casters, you can move the curvers around your shop.
| Throat Dp. | Jaw Wd. | For Max. Steel Thick. | Material | Lg. | Includes | Each | |
For Aluminum, Stainless Steel, Steel | |||||||
|---|---|---|---|---|---|---|---|
| 1 13/16" | 1 9/16" | 1/16" | Steel | 27" | Hex Key, Pair of Shrinking Jaws, Pair of Stretching Jaws, Three Shims, Wrench | 0000000 | 000000000 |
Stand | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Throat Dp. | Jaw Wd. | For Max. Steel Thick. | Material | Ht. | Wd. | Dp. | Ht. | Wd. | Dp. | Features | Each | |
For Aluminum, Stainless Steel, Steel | ||||||||||||
| 1" | 1 3/4" | 3/64" | Steel | 5 1/2" | 1 3/4" | 4 1/2" | 42" | 20" | 22" | Two Foot Pedals, Two Rigid Casters | 0000000 | 000000000 |
Hand-Held Sheet Metal Benders for Long Folds
Create long, uniform folds on the edges of sheet metal. Insert the end of a sheet into either side of these tools to form 3/8" or 1" deep folds.
Hand-Held Sheet Metal Benders for Large Sheets
Make deep folds in roofing panels and other large pieces of sheet metal. Set the throat depth up to 19 5/8". Unlike bench-mount benders, these lightweight benders are easily moved from place to place.
| Throat Dp. | Jaw Wd. | For Max. Steel Thick. | Max. Bending Angle | Lg. | Ht. | Material | Each | |
For Aluminum, Stainless Steel, Steel | ||||||||
|---|---|---|---|---|---|---|---|---|
| 3 1/8"-19 5/8" | 19 5/8" | 1/64" | 150° | 31 1/2" | 4 1/4" | Steel | 0000000 | 0000000 |
Hand-Held Sheet Metal Benders for Opening Seams
Open sheet metal seams without cutting. The jaws slide under seams to pry the sheets apart. Because you’ve unfolded the sheet metal instead of cutting it, you can reuse both panels.
| Jaw Wd. | Lg. | Material | Each | |
For Aluminum, Brass, Copper, Stainless Steel, Steel | ||||
|---|---|---|---|---|
| 1 1/4" | 10" | Steel | 0000000 | 0000000 |
Wire, Rod, and Flat Stock Curvers
Also known as ring rollers, these curvers shape wire, rods, and flat stock into curves and circles. Turn the handle to drive material through the steel rollers. With each pass through the rollers, tighten the tensioner knob in small increments to gradually increase the curve.
Curvers with stand come with three sets of rollers—one for flat stock and two for wire and rods. They can apply pressure from either side of the bottom roller, creating more curve options.
For Max. Flat Stock | Stand | Mounting Holes | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Wire Dia. | Thick. | Wd. | For Rod Dia. | Min. Bending Radius | Material | Ht. | Wd. | Dp. | Handle Lg. | Roller Dia. | Ht. | Wd. | Dp. | Mounting Fasteners Included | No. of | Dia. | Each | |
For Aluminum, Brass, Copper, Stainless Steel, Steel | ||||||||||||||||||
| 1/4" | 3/16" | 1" | 1/4" | 1 1/2" | Steel | 5 1/2" | 6 1/2" | 5 1/2" | 13 1/2" | 1 1/4" | __ | __ | __ | No | 2 | 3/8" | 0000000 | 0000000 |
| 1/4", 1/2" | 3/16" | 1" | 1/4", 1/2" | 1 3/8" | Steel | 6 3/4" | 5 1/2" | 9 3/4" | 9" | 1 13/16" | 39" | 21" | 21" | Yes | 2 | 5/16" | 0000000 | 000000 |
Wire, Rod, and Flat Stock Benders
Bend wire and rod up to 1/2" diameter and flat stock up to 1/4"×1" with this rugged steel bender. Use it to create hooks, brackets, and pipe hangers. It can be clamped in a vise.
For technical drawings and 3-D models, click on a part number.
For Max. Flat Stock | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Die Dia. | For Max. Wire Dia. | Thick. | Wd. | For Max. Rod Dia. | Material | Lg. | Wd. | Ht. | Each | |
For Brass, Copper, Stainless Steel, Steel | ||||||||||
| 3/4", 1 1/4", 1 5/8" | 1/2" | 1/4" | 1" | 1/2" | Steel | 20" | 2" | 5" | 0000000 | 000000 |
Economy Wire, Rod, and Flat Stock Benders
Bend wire and rod up to 3/8" diameter and flat stock up to 1/2"×3/16" to create hooks, brackets, and pipe hangers. They can be clamped in a vise.
For technical drawings and 3-D models, click on a part number.
Wire, Rod, and Flat Stock Benders for Complex Shapes
Create squares, coils, and S-shapes. This bender can be mounted to your bench top or clamped in a vise. Circle pins make additional sizes of bends and coils.
For Max. Flat Stock | Mounting Holes | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Max. Wire Dia. | Thick. | Wd. | For Max. Rod Dia. | Pin Dia. | Material | Lg. | Wd. | Ht. | Mounting Fasteners Included | No. of | Dia. | Handle Lg. | Includes | Each | |
For Brass, Copper, Stainless Steel, Steel | |||||||||||||||
| 5/16" | 1/8" | 1" | 5/16" | 3/16", 1/4", 1/2", 1", 1 1/4", 1 1/2", 1 3/4" | Steel | 9 1/2" | 2 1/2" | 3 1/2" | No | 2 | 5/16" | 12" | Forming Pin, Seven Circle Pins, Stop Pin, Two Sharp-Angle Dies | 0000000 | 0000000 |
Hand-Held Sheet Metal Edge Shapers
With a single tool, create both sharp creases and soft curves along the edges of sheet metal. Also known as edge rollers, these tools slide back and forth along edges to create even bends. Unlike benchtop sheet metal tools, these shapers are portable, so they’re often used on-site by roofers. Use 1/8” markings to set up precise bends.
| Throat Dp. | For Max. Steel Thick. | Max. Bending Angle | Graduation Marks | Numeric Increments | Lg. | Material | Each | |
For Aluminum, Stainless Steel, Steel | ||||||||
|---|---|---|---|---|---|---|---|---|
| 3/8"-8" | 1/32" | 90° | 8ths | 1" | 13 1/2" | Steel | 0000000 | 0000000 |
Tight-Grip Sheet Metal Benders and Crimpers
These tools lock onto your material to prevent them from opening while bending and crimping.
| Throat Dp. | Jaw Wd. | Lg. | Material | Each | |
| 1 3/4" | 3 1/8" | 8" | Steel | 0000000 | 000000 |
Depth-Measuring Sheet Metal Benders and Crimpers
The jaws have V-notches in 1/4" increments to measure the depth of bends.
| Throat Dp. | Notch Increments | Jaw Wd. | Lg. | Material | Each | |
| 1 1/4" | 1/4", 1/2", 3/4", 1", 1 1/4" | 3 1/4" | 8" | Steel | 0000000 | 000000 |
Depth-Measuring Sheet Metal Benders and Crimpers for Tight Spaces
Offset handles allow you to use this tool in tight spaces. The jaws have V-notches in 1/4" increments to measure the depth of bends.
| Throat Dp. | Notch Increments | Jaw Wd. | Lg. | Material | Each | |
| 1 1/4" | 1/4", 1/2", 3/4", 1", 1 1/4" | 3 1/4" | 9" | Steel | 0000000 | 000000 |
Duct Crimpers for Impact Drivers
Turn your impact driver into a power crimper, and create raised edges on sheet metal more quickly than hand crimpers. Use on standard 30-24 ga. galvanized steel HVAC ductwork. They work with impact drivers in forward or reverse, so they are comfortable for both right- and left-handed users.
For Impact Driver | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Throat Dp. | Jaw Wd. | Lg. | For Steel Gauge | For Crimp Dp. | Hex Shank Size | Max. Current, A | Min. Voltage | Material | Each | |
| 1 1/2" | 2" | 4" | 30-24 | 1 1/2" | 1/4" | 7 | 12V DC | Steel | 0000000 | 0000000 |
Sheet Metal Edge Shapers
Make different edge styles on your sheet metal. It comes with rollers for turning, wiring, burring, beading, and crimping.
Roller | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Throat Dp. | Ht. | Wd. | Dp. | For Max. Steel Thick. | Mount Type | Max. Mounting Surface Thick. | Material | Ctr.-to-Ctr. | Material | Includes | Each | |
| 7" | 35" | 15 3/8" | 21 1/8" | 1/64" | C-Clamp | 2 3/4" | Steel | 2" | Cast Iron | Rollers for Burring, Crimping, Wiring, 1/8" Turning, and 3/4" Ogee Bending | 0000000 | 000000000 |
Tear-Preventing Sheet Metal Benders and Crimpers
Rounded jaws reduce damage to aluminum and other lightweight metal.
| Throat Dp. | Jaw Wd. | Lg. | Material | Each | |
| 1" | 3 1/2" | 8" | Steel | 0000000 | 000000 |
High-Force Sheet Metal Crimpers
This tool has five blades and compound-leverage action for more power with less effort than other crimpers. Use it to join pieces of metal duct and gutters. Jaws have V-notches in 1/4" increments to measure the depth of bends.
| Throat Dp. | Notch Increments | Jaw Wd. | Lg. | Material | Each | |
| 1 1/4" | 1/4", 1/2", 3/4", 1", 1 1/4" | 7/8" | 9 3/4" | Steel | 0000000 | 000000 |
Benchtop Rolling Mills
With hardened rollers and precision-machined gears, these rolling mills stand up to heavy use. They’re often used to compress sheets to an uncommon gauge size, convert scrap metal into sheets or wire, or create different thicknesses in a single piece of metal without welding multiple pieces together. After several passes through the mill, you may need to anneal your metal to soften it and prevent cracking.
Manual mills are gear driven, making them easier to turn than direct-drive rolling mills. Their rollers have grooves so you can form square and half-round wire in addition to sheets.
Electric mills do not require hand cranking, so they provide the power you need to complete high volumes of work. They have flat rollers for creating uniform sheets.
Gear speed ratio indicates the force it takes to turn the output gear. For instance, the manual rolling mill has a 4:1 gear ratio, meaning that you rotate the handle four times to turn the gear powering the rollers once.
For Max. Steel | Roller | Mounting Holes | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Wd. | Thick. | Square Wire Size | Half-Round Wire Size | Gear Speed Ratio | Ht. | Wd. | Dp. | Handle Lg. | Dia. | No. of | Material | Frame Material | Mounting Fasteners Included | No. of | Dia. | Each | |
For Aluminum, Brass, Stainless Steel, Steel | |||||||||||||||||
| 2 9/16" | 3/16" | 3/64", 5/64", 1/8", 5/32", 3/16", 13/64", 7/32", 15/64", 1/4" | 0.098", 0.118", 0.157" | 4:1 | 14" | 12" | 8" | 12" | 2 1/2" | 2 | Steel | Cast Iron | No | 6 | 3/8" | 0000000 | 0000000 |
For Max. Steel | Roller | Mounting Holes | |||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Wd. | Thick. | Gear Speed Ratio | Ht. | Wd. | Dp. | Dia. | No. of | Material | Frame Material | Horsepower, hp | Max. rpm | Current, A | Voltage | Cord Lg., ft. | Mounting Fasteners Included | No. of | Dia. | Each | |
For Aluminum, Brass, Stainless Steel, Steel | |||||||||||||||||||
| 6 1/4" | 3/16" | 100:1 | 19" | 22" | 15" | 2 1/2" | 2 | Steel | Cast Iron | 1/2 | 13 | 1.7 | 120V AC | 5 | No | 4 | 1/2" | 0000000 | 000000000 |