With all PTFE wetted parts, these pumps offer the best chemical resistance of all our air-powered transfer pumps and can handle solvents and petroleum-based fluids that PVDF pumps can’t.

A Buna-N diaphragm stands up to lubricating oil such as hydraulic and motor oil. These pumps are designed to handle thick sludges and slurries.

These pumps have a PTFE diaphragm compatible with oil, fuel, and chemicals such as mineral spirits, methyl ethyl ketone (MEK), and xylene. They have a rugged aluminum housing for moving large volumes of thick sludges and slurries in demanding environments.

The Santoprene diaphragm resists cracking for a long service life and stands up to water and chemicals such as ammonium hydroxide. These pumps have a rugged aluminum housing for moving large volumes of thick sludges and slurries in demanding environments.

A neoprene diaphragm stands up to oil and chemicals such as isopropyl alcohol and deionized water. These pumps have large internal pathways and check valves with flaps to accommodate thick sewage, abrasive slurries, and industrial waste with large solids that would damage standard air-powered transfer pumps.

With a 316 stainless steel housing and a fluoroelastomer diaphragm, these pumps resist a variety of harsh acids and alkalies, such as phosphoric acid, nitric acid, and sulfuric acid. They have large internal pathways and check valves with flaps to accommodate thick sewage, abrasive slurries, and industrial waste with large solids that would damage standard air-powered transfer pumps.

These pumps have an impact-resistant aluminum housing and handle larger solids than other battery-operated water-removal pumps. Use them to remove water from areas without power.

Pumps have a powerful motor that provides more than twice the flow rate of standard water-removal pumps to quickly remove large volumes of liquid. They activate when plugged in; add a float switch to control when the pump activates.

Built with high-chromium stainless steel components, these pumps stand up to salt water with up to 25% sand by volume and resist wear caused by abrasive particles. Fill the fuel tank with gasoline to remove water at sites without power.

Install these pumps right in your line and engage the lever handle to start pumping.

Transfer raw sewage water that contains solids up to 2” in diameter. These pumps have a float switch with a separate cord that can unplug, so you can replace the switch without replacing the whole pump.

Also known as grinder pumps, these pumps have stainless steel blades that prevent clogs by breaking down sewage into an easy-to-transfer slurry. The float switch is wired to the pump.

These pumps provide about 25% more flow than standard float-switch activated pumps for sewage water. Equipped with a large intake and rugged impeller, they transfer raw sewage water with solids up to 2” in diameter. The float switch is wired to the pump.

Pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Equipped with a large intake and rugged impeller, these pumps transfer raw sewage water with solids up to 2” in diameter.

The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Equipped with a large intake and rugged impeller, these pumps transfer raw sewage water with solids up to 2” in diameter.

Pumps have a heavy duty motor with sealed bearings that generates a flow rate similar to our other sump pumps for sewage water while using fewer amps. Connect them to a three-pronged plug or wire them directly to a power source to activate. Pumps transfer raw sewage water with solids up to 2” in diameter.

Since the motor is totally enclosed fan cooled (TEFC) and never comes into contact with the water, these pumps can be used with hot water up to 200° F.

Move higher volumes of water with solids than other sump pumps. The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Also known as effluent pumps, they accommodate solids up to 3/4” in diameter. They are often used with liquid waste that has passed through a septic tank, so most solids are removed.

These pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Also known as effluent pumps, these accommodate solids up to 3/4" in diameter. They're often used with liquid waste that has passed through a septic tank, so most solids are removed

Use these pumps at temperatures up to 200° F. Also known as effluent pumps, they accommodate solids up to 3/4” in diameter. They’re often used with liquid waste that has passed through a septic tank, so most solids are removed. The float switch is adjustable and wired to the discharge pipe.