These are also known as tappet wrenches.

One head is angled 60° for access to hard-to-reach fasteners. These are also known as ignition wrenches.

These wrenches are made of stainless steel for excellent corrosion resistance.

Sized for working on small equipment, these wrenches are 4 1/8" long with a slim head and handle.

The opening shape makes more contact with fasteners for a better grip than standard open-end wrenches. These tools are also known as flare-nut or line wrenches.

Also known as alligator wrenches and water-meter nut wrenches, the V-shaped head fits multiple hex fastener sizes.

Also known as spud, structural, and construction wrenches, use the pointed end of the handle to align bolt holes during assembly.

The slim heads fit into tight spaces and around thin fasteners.

These lightweight tools are also known as AN (Army-Navy) wrenches.

One head is angled 60° for access to hard-to-reach fasteners. These are also known as ignition wrenches.

When turning fasteners in small spaces, these short wrenches fit where others can't.

The opening shape makes more contact with fasteners for a better grip than standard open-end wrenches. These tools are also known as flare-nut or line wrenches.

A ratchet mechanism allows you to turn fasteners in tight spaces without removing and repositioning the wrench.

The 25° offset heads give you additional clearance to turn hard-to-reach fasteners.

Open the jaws to fit around a fastener like an open-end wrench; close the jaws and the wrench acts like a ratcheting box wrench.

Also known as slugging wrenches, strike the handle with a hammer to break stuck fasteners free.

The head is offset 45° to provide clearance for reaching over obstructions.

Also known as half-moon and obstruction wrenches, the shape lets you reach around obstacles and into machinery.

Also known as spud, structural, and construction wrenches, use the pointed end of the handle to align bolt holes during assembly.

The head is offset 45° to provide clearance for reaching over obstructions.

These wrenches are polished for a mirror-like finish.

Open the jaws to fit around a fastener like an open-end wrench; close the jaws and the wrench acts like a ratcheting box wrench.

The jaws on these wrenches are shaped to turn slip nuts, jam nuts, and large hex nuts.

The handle is covered in plastic for a comfortable grip.

The adjustment knurl won't turn when the wrench is being used, preventing accidental loosening of the jaws.

A plastic-covered handle provides a comfortable grip.

An insulated handle protects against accidental contact with live electrical circuits. These wrenches are tested to 1,000 volts to meet IEC 60900.

Also known as a basin wrench, this tool has a pivoting head and spring-close jaws for working in tight spaces where it’s difficult to adjust a traditional wrench.

Flip the wrench over to use the raised section on the head as a hammer.

Reverse the movable jaw to convert from a smooth-jaw adjustable wrench to a serrated-jaw pipe wrench.

Turn fasteners with the firm grip of a wrench and the adjustability of pliers.

Quickly find the wrenches you're looking for with these brightly colored sets.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

When working in tight spaces, these short wrenches fit where others can't.

Suitable for occasional maintenance work, these sets are imported.

Pivot the box end for access to fasteners in tight spots.

A lever reverses the ratchet direction.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Made of materials that are Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

When working in tight spaces, these short wrenches fit where others can't.

A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.

A lever reverses the ratchet direction.

Flip these wrenches over to ratchet in the opposite direction.

Pivot the socket end to access hard-to-reach fasteners.

These wrenches have one pivoting socket end and one open end.

Often used with an extension, these sockets turn fasteners and fittings in obstructed areas that a regular socket can't reach. They are also known as crowfoot wrenches.

These sockets are also known as pin-in-Torx bits.

The short Phillips bit on these sockets fits in spaces that screwdrivers can’t and where height clearance is limited.

An extra-long Phillips bit allows these sockets to reach far-away fasteners. Use them where standard or stubby sockets can’t reach.

An opening at the tip of these sockets fits around the security pin, allowing you to drive tamper-resistant Torx Plus screws.

These sockets are also known as pin-in-hex or pin-in-socket bits.

Tighten and loosen fasteners at an angle by pivoting the head on these sockets.

Extra-long bits allow access to hard-to-reach fasteners.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet ASTM F1505 and IEC 60900.

The rounded-corner shape fits over ball joints commonly found in suspension and steering systems in vehicles.

Slide the open side of these sockets over a tube or hose to adjust a nut that’s already installed.

When vertical space is tight or you need an extra twist on your socket, use one of the dual-drive Phillips bit sockets in this set.

Keep a convenient mix of hex, Torx, Phillips, and slotted bit sockets on hand.

Extra-long bits allow access to hard-to-reach fasteners.

Tighten or loosen hard-to-reach fasteners with the extra-long bits in these socket sets.

The short bit on these sockets fits in spaces where height clearance is limited.

A spring-loaded ball on the bit holds fasteners in place as you drive them, including nonmagnetic fasteners like stainless steel screws.

Extra-long bits help you access hard-to-reach fasteners.

The opening shape makes more contact with fasteners for a better grip than standard open-end sockets. Also known as flare-nut or line wrench sockets, they're often used with flared tube fittings and fuel and hydraulic lines.

Built for durability, these wrenches handle the demands of high-volume production and tough maintenance applications.

Turn sockets in the most confined spaces.

Made of aluminum-bronze, these wrenches satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

No need to pull the socket off the tool—push a button to release.

When the ratchet head becomes worn or damaged, change it out for a new one.

No need to pull the socket off the tool—push a button to release.

Also known as a construction or spud handle, wrenches use the pointed end to align bolt holes.

A ratchet mechanism allows you to turn fasteners without removing and repositioning the wrench.

Cut the supply of water or gas.

The jaws grip most round surfaces, even highly polished objects. Push down on the wrench and pull the handle toward you—the jaws will tighten around the workpiece.

Made of aluminum-bronze that is Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant. They are also known as railroad wrenches.

There's no adjustment nut or button on these wrenches—a spring-loaded hinge automatically closes the top jaw around pipe.

Made of materials that are Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant.

Turn the end of the handle to set torque, and the wrench makes an audible click when it reaches the setting.

Sets include various sizes of wrenches that are shaped to fit round holes on the circumference of collars, bearings, and other machine tool components.

These wrenches are shaped to fit round holes on the circumference of collars, bearings, and other machine tool components.

Made of stainless steel, these wrenches have excellent corrosion resistance.

Fit these wrenches into slots on the circumference of collars, bearings, and other machine tool components.

Made of aluminum-bronze that is Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

In addition to a long handle, these wrenches include two heads with different hook widths.