We will reply to your message within an hour.
These switches withstand temporary submersion.
With a slim shape, these switches fit comfortably in your hand.
Control cranes and other mobile machinery in dirty, outdoor, and wet environments without damaging your switch.
Operate equipment from up to 330 feet away—these switches include a transmitter and a receiver that connects to equipment.
These switches meet MIL-S-3950.
Install in 14 mm dia. cutouts.
Install in 12 mm dia. cutouts.
With a stainless steel enclosure, these switches are more durable than aluminum and plastic. They're rated NEMA 4X for protection from corrosion and washdowns.
More lightweight than steel or stainless steel, these aluminum enclosed switches are rated NEMA 4X for protection from corrosion and washdowns.
Rated NEMA 4X and 13, all switches resist corrosion and can withstand washdowns and oil/coolant spraying.
Keep a switch within reach—but not in the way. These mount to the underside of desks, tables, and shelves to keep work surfaces clear and reduce the risk of accidental presses.
Rated NEMA 3S, NEMA 4X, NEMA 13, and IP66, these plastic switches resist corrosion better than aluminum switches and withstand washdowns and oil/coolant spraying.
A red light flashes when the actuator is pushed, making it easy to see from a distance. They're rated IP65 for protection from washdowns.
These aluminum switches are rated NEMA 4, NEMA 13, and IP66 for protection from washdowns and oil/coolant spraying.
Suitable for areas with space limitations, these switches have a low profile and a small footprint. They lay flat or mount to a wall.
The enclosure not only protects these switches, but also adds options for how you install them.
Pull the hanging rope in any direction to actuate these switches.
Immediately cut power by pulling the cable.
Control equipment from up to 40 feet away—these switches include a transmitter and a receiver that connects to equipment.
Operate these switches hands-free when working in damp or humid environments.
Keep your hands free for other tasks by triggering switches with your foot.
Step on these switches for hands-free actuation in an area with frequent washdowns.
When the pedal is pressed, the built-in potentiometer adjusts the resistance to vary the speed for motor drives.
Rated NEMA 6P and IP68, these switches are protected against washdowns, corrosion, and temporary submersion.
Made with stainless steel conductors, these switches resist corrosion in damp areas. They’re less than 1/4” thick, so they’ll fit under floor mats and in other tight spaces.
These narrow switches are also thin enough to be hidden under carpeting or installed anywhere space is limited.
Prevent personnel from getting too close to dangerous equipment while it’s running. Step anywhere on these mats and they can turn on warning lights and alarms or shut down equipment.
Step or press anywhere along the switch to control doors, lights, or alarms.
Customize the length of these switches by cutting them from a 50-foot roll.
Thicker than standard safety switch mats, these withstand repeated impact from heavy and sharp objects.
Sealed actuators prevent these switches from jamming, even when exposed to oil, sand, mud, or ice.
With a rubber-encased housing and stainless steel bracket, these switches resist vibration and corrosion. They're rated IP68 for protection from dust and temporary submersion.
Keep out dirt and moisture—the sealed housing on these switches is watertight and meets MIL-PRF-8805.
Enclosures protect these snap-acting switches from the environment.
Rated IP67, these switches have an enclosure that shields their interior during temporary submersion. They open and close circuits quickly to prevent arcing and keep contacts from sticking.
Rated NEMA 4 , these enclosed switches have a sealed actuator for protection from washdowns.
Use these switches where ignitable gas and dust may be present. They meet NEC Class I, Division 1, Groups B, C, and D; and Class II, Division 1, Groups E, F, and G for hazardous locations.
Small enough to fit in the tiniest spaces, these switches are rated IP67 for protection from temporary submersion.
These switches actuate with the slightest push for a high degree of accuracy. They're rated IP67 for protection from wet locations and temporary submersion.
Prevent equipment from automatically restarting—these switches must be manually reset each time they're actuated.
Rated NEMA 6P, 13, and IP67, these switches are protected from corrosion, oil/coolant spraying, washdowns, and temporary submersion.
Sealed actuators prevent these switches from jamming, even when exposed to sand, mud, or dirt. They're rated IP67 for protection from temporary submersion.
Shorter and thinner than other safety limit switches, these are sized to fit tight spaces.
Protect machinery and ensure the safety of personnel—these switches will open the circuit when actuated even if a spring fails or the contacts stick.
Rated IP67, these switches are protected from temporary submersion. When an object in motion comes into contact with the actuator, it sends a signal to open or close a circuit.
Stack these slim switches together, or fit them into tight spaces. They're rated IP67 for protection from temporary submersion.
Secure these switches into panels using mounting nuts.
Prevent automatic doors from closing on a person or an object—these switches immediately turn machinery off when actuated with minimal force.
Minimize false triggers—these switches require 10 lbs. of actuation force in order to shut off machinery immediately.
Replace access door hinges with these switches; they actuate when the door opens at least 4°.
Often used with machine guards, these switches mount to a door frame.
Delay access to hazardous areas until conditions are safe; use these switches with machines that take time to stop after they are turned off. They mount to a door frame.
Sensitive along their entire length, these switches are often used to signal when an overhead door closes or an item reaches the end of a conveyor.
Mounted to your circuit board, these switches trigger when magnetic components get near, and reset as they move away.
These switches actuate when a magnet comes within sensing distance, and reset when the magnet moves away.
Prevent unauthorized use—these switches require coded magnets to actuate. They cannot be bypassed using ordinary magnets.
Rotate the face on these switches five different directions for easy installation and positioning—they work with both AC and DC inputs.
Mount these flat inductive switches to a base or rail to remotely detect metallic objects in wet and dirty environments.
Switches accept both AC and DC input voltage.
Easily mount these flat switches to a base or rail.
Eliminate the need to calculate the sensing distance when using different metals—these switches sense all metal at the same distance. Also known as K=1 sensors.
These switches have a longer sensing distance compared to other proximity switches with the same diameter.
The short body on these switches makes them suitable for tight spaces.
Sense objects as they pass through the switch’s ring via tubing or a funnel. These switches are often used to monitor blockages, detect breaks in spooling wire, or count small metallic parts, such as screws, during the stamping process.
These switches use DC input voltage and produce PNP or NPN signal output. They're often used with programmable logic controllers (PLCs).
Turn the face on these switches to sense metallic objects from the front, sides, top, or bottom.
Mount these intrinsically safe switches to flat surfaces in volatile areas. Their low-current, low-voltage NAMUR signal means they won’t ignite or create sparks while in use. ATEX and IECEx certified, they meet international standards to protect against explosion where combustible dust and flammable gases are present.
These inductive proximity switches sense metallic objects each time they pass through the slot, even when they’re obscured by water, oil, dirt, or a surface finish. Use them to measure the speed of rotating equipment and to count or detect moving objects, such as sheet metal being fed into a stamping process.
Use these switches to sense metallic objects in environments containing flammable gases and combustible dust. ATEX and IECEx certified to protect against explosion, they produce a low-current, low-voltage NAMUR signal, so they won’t ignite or create sparks.
Twist the sensor to detect metallic objects where explosive dust or gas may be present—the sensor rotates for front, side, top, or bottom sensing. These switches are UL and C-UL listed as well as ATEX and IECEx certified for hazardous locations.
These intrinsically safe switches detect objects as they’re routed through the ring. They produce a low-current, low-voltage NAMUR signal, so they won’t ignite or create sparks. Switches are ATEX certified to protect against explosion.
Sense objects from farther away than with other DC proximity switches that have the same diameter.
For use in volatile areas, these intrinsically safe switches detect objects when they pass through the slot. They use a NAMUR signal to operate at a low current and voltage, so they won’t ignite or create sparks. ATEX and IECEx certified, they protect against explosion.
Most often found in older devices, these switches require AC input voltage.
The flexible cable on these switches withstands applications that require frequent motion, such as robotics.
With a smaller diameter and shorter length than standard sized switches, these fit in the most space-constrained areas.
These switches sense when a valve is open or closed, supporting flow and temperature control within your system and offering reliable feedback.
Support flow and temperature control in your system with these intrinsically safe switches, which sense when a valve is open or closed in volatile areas. They are ATEX and IECEx certified to protect against explosion.
These switches have a receiver built into the housing, eliminating the need to align components and measure sensing distance during installation.
For optimal performance in tight spaces, these switches have a smaller beam and can detect smaller objects than standard photoelectric switches.
With a narrow, flat body, these switches fit in tight spaces.
Rated IP69K, these switches can withstand high-pressure, high-temperature washdowns and temporary submersion.
Detect the presence or absence of an object moving at high speeds with a light beam. These switches have a longer sensing distance than proximity and ultrasonic switches.
Safely detect the presence or absence of an object moving at high speeds with a light beam. These switches produce a low-current, low-voltage NAMUR signal, so they won’t create sparks or ignite. ATEX and IECEx certified, they protect against explosion in environments containing flammable gases and combustible dust.
A built-in relay produces AC voltage output. These switches are often used with older programmable logic controllers (PLCs).
Scanning 275° side-to-side for people and objects, these switches (known as safety laser scanners) cover large areas and send signals to machinery to prevent accidents.
Set these switches to delay activation by up to fifteen seconds after detecting an object.
The highly flexible fiber-optic cable and small sensing end help you position these switches in hard to reach areas.
Set these switches to delay activation by up to five seconds after detecting an object.
Light beams travel up to 32 ft. between the transmitter and receiver.
Mount proximity switches into a panel cutout or tank wall.
Often used with programmable logic controllers (PLCs), these switches use DC input voltage and produce PNP or NPN signal output.
These switches use a NAMUR signal to operate at a low current and voltage, so they won’t ignite or produce sparks. ATEX certified, they protect against explosion in environments containing flammable gases and combustible dust. Switches sense both metallic and nonmetallic objects.
Rated NEMA 4X, 6P, IP68 and IP69K, these switches resist corrosion and high-pressure, high-temperature washdowns, and can withstand temporary submersion.
These switches detect magnetic objects—or objects with a magnet attached—through non-magnetic walls.
Rated NEMA 4, these switches are protected from washdowns.
Assemble your own motor starter by combining a switch and a thermal overload element.
Rated NEMA 4X, these enclosed starters are protected from corrosion and washdowns.
The NEMA 4X rated enclosure protects these starters from corrosion and washdowns.
Sized to fit in tight spaces, these starters have a shorter height and narrower depth than most other starters.
If there’s a power outage, flip the toggle for each circuit on these switches to backup power.
When the microcontroller inside detects a power outage, these switches automatically fire up a backup generator. They’ll switch back to utility power once power is restored.
Install these switches in a panel cutout.
These switches are housed in a protective enclosure so they can be mounted wherever needed.
Protected by a steel enclosure, these switches withstand tougher conditions than switches in a plastic housing. Also known as safety switches, they have quick-make/quick-break action to eliminate arcing and prolong switch life.
A raintight NEMA 3R rated enclosure protects these switches outdoors.
Rated IP69K, these switches are protected from high-pressure and high-temperature washdowns.
Rated IP66, these switches are protected from washdowns.
Control and diagnose issues with safety-critical circuits.
Cover robot arms and tools with this padding to help prevent injuries in areas where people are working nearby. When the padding is touched, pressure sensors signal your machine to stop moving.