Epoxies are the strongest and most weather- and chemical-resistant structural adhesives. They work especially well on metals.

For quick repairs, these epoxies begin to harden in 6 minutes or less.

To allow time to adjust and position parts, these epoxies remain workable for at least 90 minutes.

With excellent resistance to corrosive chemicals and salt water, these epoxies work in tough conditions.

Toughened adhesives are blended with rubber particles for better impact resistance than standard epoxies. They form flexible, resilient bonds.

Bond most materials without the strong odor of other epoxy adhesives.

Bond new concrete to old concrete, or use this adhesive as a primer on concrete surfaces.

Permanently set threaded rods, studs, and rebar in concrete.

Thicker than polyurethane and paint, these coatings have high moisture resistance and protect against abrasion and chemicals.

Cover sharp edges, corners, and weld seams with these thick epoxy coatings for protection against cuts and snags.

The strongest of the potting compounds, epoxies are rigid and wear resistant. They have excellent chemical and moisture resistance, withstand a wide range of temperatures, and provide excellent electrical insulation.

Protect circuit boards and other electronics where high heat is a concern but you don’t need to transfer that heat elsewhere. These compounds are a good middle ground between standard epoxy compounds and heat-transfer compounds.

Formulated to draw heat away from sensitive electronic components, these potting compounds have higher thermal conductivity than standard potting compounds.

Thinner than potting compounds, these rigid and wear-resistant coatings flow easily into small spaces between electrical components. Use them to secure and insulate hardware on printed circuit boards.

High humidity, harsh chemicals, water submersions, and salt are no match for these electronic coatings.

Use these coatings on tanks to create a low-friction lining that prevents bubble formation and turbulence in the liquids within.

These coatings are some of the thickest and most durable on the market. They protect against abrasion and resist moisture and chemicals.

Longer-lasting than antislip tape, these coatings contain grit to provide traction. They’re good for areas with pedestrian traffic.

These provide the highest traction and impact resistance of our antislip coatings. Longer-lasting than antislip tape, these coatings contain grit to provide traction.

Also known as coal tar epoxy, these coatings are our most resistant to abrasion, chemicals, and corrosion on concrete and steel. They can be immersed in salt water and fresh water.

Use these solvent-free, high-gloss coatings to protect concrete floors in enclosed areas. Durable enough for forklift traffic, they resist stains, moisture, and chemicals.

Prepare metal surfaces for powder coating. These primers create a base layer that bonds with your top coat to extend the life of your powder coating.

A high concentration of zinc gives these primers excellent corrosion resistance for protecting steel—when exposed to moisture and chemicals, the zinc rusts before the underlying steel can. They’re often used with structural steel.

Protect steel and iron parts from corrosion without having to remove the primer before welding them together. Often used on structural steel in demanding environments, these primers can be welded through without affecting the weld’s integrity.

These thin primers penetrate deeply into concrete floors to create a hard surface that can then be coated with any urethane or epoxy coating.

Mix these two-part surface fillers together to repair leaks and cracks as well as to rebuild rough spots in metal.

For use in processing equipment that carries small particles less than 1/16" in diameter, these ceramic-filled epoxies rebuild and repair surfaces exposed to abrasion from particles, such as dust collectors, fan blades, and fan housings.

Repair and rebuild metal surfaces that are exposed to heat. These surface fillers withstand temperatures over 450° F.

To stop leaks in metal tanks and equipment without draining the contents, heat the area with a heat gun or torch to melt the stick and form a permanent seal. The resulting patch can withstand pressure up to 600 psi.

Dispense ready-to-use conductive liquid to fill pits and small gaps on circuit board components.

These surface fillers can be used on vertical surfaces without sagging. They repair cracked, worn, and damaged surfaces.

Make castings and fill voids with these two-part pourable epoxies.

Mix these two-part epoxy surface fillers to create a strong repair in wet environments or underwater.

Fill cracks up to 10" deep on vertical and overhead surfaces.

Fill cracks up to 4" deep on horizontal surfaces, such as floors and sidewalks.

Use these two-part compounds to patch concrete floors, stairs, and walls in cold environments, such as freezers. At room temperature, they cure faster than any of our other concrete patching compounds.

Repair sidewalks and factory floors in areas with heavy pedestrian traffic. They can also be used to fill minor depressions and cracks.

These leveling compounds stand up to acid and chemical spills, making them a good choice for corrosive environments. They also withstand steel wheels and heavy impacts.

Press these putty-like fillers into cracks in wood up to 1/8" wide.