Right Hand Screws | McMaster-Carr

Filter by

System of Measurement

Thread Size

Length

Fastener Head Type

Material

Drive Style

Threading

Finish

Head Diameter

Socket Head Profile

Head Height

Thread Pitch

Thread Direction

Thread Type

Screw Size

Rounded Head Style

Fastener Strength Grade/Class

Thread Spacing

Drive Size

Specifications Met

Tensile Strength

Countersink Angle

Flat Head Profile

How can we improve?

69,451 Products

Fastening and Joining

Socket Head Screws

Socket Head Screws

With a deeper drive than flat and rounded head screws, these withstand more torque for a tighter hold

Rounded Head Screws

Rounded Head Screws

Sit just above the surface for a low-profile finish and hold tighter than flat head screws

10,367 products

Hex Head Screws

Hex Head Screws

Used with nuts to create a stronger joint than flat and rounded screws

Flat Head Screws

Flat Head Screws

Fit in countersunk holes for a flush finish

Tapping Screws

Fasten a range of materials together without needing to tap the hole first

Shoulder Screws

Shoulder Screws

Rotate parts around the cylinder under the head to guide and align them during installation

Set Screws

Exert pressure at the tip to hold parts in place, unlike screws that hold material together with threads

Wood Screws

Fasten material to wood or pieces of wood to each other

Tighten and loosen by hand without the need for tools

Carriage Bolts

A smooth head provides a finished look while a square neck keeps the bolt in place when using a nut

12-Point Screws

12-Point Screws

12 contact points handle more torque than a hex head while a flange eliminates the need for a washer

Captive Panel Screws

Captive Panel Screws

Secure panels and enclosures while still having access to them

Drywall Screws

Fasten panels of drywall to materials such as wood, metal, and drywall

Fastener Assortments

Fastener Assortments

Stay prepared by keeping fasteners in common sizes and materials on hand

Square Head Screws

Square Head Screws

Turn the large flat sides with a wrench into square holes that stop further rotation

Studs

Press, weld, or screw in place to add a threaded fastening point

Elevator Bolts

Create a flush joint to allow movement in tight spaces such as grain elevators and belting systems

Hanger Bolts

Suspend pipe and other fixtures with wire or cable ties

T-Bolts

Turn by hand for easy fastening, use as a handle, or attach as a point for straps and clamps

Plow Bolts

The head sits flush with countersunk holes while the bolt stays in place when tightening a nut

Pentagon Head Screws

Pentagon Head Screws

Create a tamper-resistant joint with a head than can only be removed with a 5-point socket

Hold-Down Bolts

Hold-Down Bolts

Hold material under the bent head while the other end is tightened down with a nut

Joint Clamps for Wood

Joint Clamps for Wood

Make secure joints between boards, butcher blocks, and countertops

Binding Barrels and Screws

Binding Barrels and Screws

Thread together for a low-profile fastener

Threaded Rods

Anchor, connect, or hang components in a wide variety of applications

Single-End Studs

Single-End Studs

Use the unthreaded end as a pivot point, hinge, shaft, or locator pin

Anchors

Secure structural joints in concrete, brick, and other building materials

Spring Plungers

Spring Plungers

Apply accurate, consistent pressure for positioning, indexing, and ejecting parts

Rivet Nuts

Add threads to thin panels with access from only one side; also known as blind inserts

Weld Nuts

Weld to metal surfaces to add permanent threads

Anchor Toggles

Replace your anchor toggle if it falls when removing your toggle bolt

Thread Adapters

Thread Adapters

Join threads of a different type, size, and gender

Power Transmission

Lead Screws and Nuts

Lead Screws and Nuts

Components travel along a screw with broad, square threads to clamp and lift heavy loads

Ball Screws and Nuts

Ball Screws and Nuts

Internal ball bearings roll on screws for low friction when moving components at high speeds

Connecting Rods

Connecting Rods

Use with rod ends and swivel joints to link components in push/pull assemblies

Ball Screw/Splines

Ball Screw/Splines

Transmit rotary power, move loads along the shaft, or do both at once

Roller Screws and Nuts

Roller Screws and Nuts

More contact points to move heavier loads than ball and lead screw assemblies

Building and Machinery Hardware

Knobs

Position, tighten, and secure fixtures and equipment

Indicating Knobs

Indicating Knobs

Control devices and view settings at a glance

Pull Handles and Knobs

Pull Handles and Knobs

Open and close cabinets, drawers, and doors on machines and equipment

Fabricating and Machining

Setup Studs

Secure setup clamps and fixtures to your machine table or assemble heavy machines

Lathe Tool Insert Holder Replacement Parts

Lathe Tool Insert Holder Replacement Parts

Replace clamps, screws, shims, and other parts in lathe tool insert holders

Clamps

Hold workpieces securely in place

Electrical

Grounding Lugs

Create a common grounding path for internal components and circuits, as well as the enclosure body

The quick brown fox jumped over the lazy dog. Pedestal (35" Ht. x 4" Wd. x 4" Dp.)