Also known as drawn-cup roller bearings, these are our thinnest roller bearings. The outer ring is drawn out to form a lip that holds the bearing together.

These steel ball bearings handle higher loads than stainless steel and plastic bearings.

Wider than our standard ball bearings, these rugged bearings are good for handling heavy loads at low speeds.

For greater accuracy and higher speeds, these bearings are made to tighter tolerances than standard ball bearings.

Good for use in electric motors and power generators, these bearings have ceramic balls that insulate against stray current to prevent damage to the bearing.

Mount these bearings onto a hex shaft.

Mount these bearings onto a square shaft.

A solid polymer lubricant surrounds the balls, eliminating the need for additional lubrication. Bearings are 440C stainless steel.

Good for applications with incidental food contact, these 440C stainless steel bearings have a food-grade, solid polymer lubricant between the balls and race that eliminates the need for additional lubrication.

Made of slippery plastic, these bearings do not require lubrication and have excellent corrosion and chemical resistance.

Made of PVDF, these bearings resist moisture absorption, so they won’t warp in underwater applications.

No need to worry about precisely aligning these bearings—they swivel to compensate for up to 5° of shaft misalignment.

Install these acetal bearings in caustic environments and where lubrication can’t be used. They have good all-around corrosion and chemical resistance.

Slip these bearings onto a shaft and secure with the included set screws, no special tools required.

Made with either PEEK or graphite, these ball bearings work in applications that are too hot for most other ball bearings.

Unlike other ball bearings, these do not need to be fully inserted into a housing. A spline around the outside of the bearing creates a permanent, secure hold in thin panels.

Ball bearings operate with less friction than other bearings, so they can run at higher speeds.

A solid polymer lubricant surrounds the balls, eliminating the need for additional lubrication.

Also known as tapped-base bearings, these ball bearings mount to surfaces from the bottom through threaded holes. Because of their narrow profile, they’re commonly used in tight-clearance spaces, including systems where multiple shafts are mounted close together.

The lubricant in these mounted ball bearings is NSF registered H1 and FDA compliant for incidental contact with food.

These bearings have the highest speed ratings of any mounted ball bearing that we offer.

These bearings are rated IP69K as able to withstand washdown environments such as food, pharmaceutical, and chemical plants. Their fluoropolymer-coated housing is as corrosion resistant as 304 steel and safe for contact with food.

A bolt in each corner makes for a secure, even hold.

The lubricant in these mounted ball bearings is suitable for incidental contact with food.

Synthetic grease enables these bearings to operate in temperatures up to 400° F—nearly double the maximum temperature of standard mounted ball bearings with four-bolt flange.

Ball bearings operate with less friction than other bearings, so you can run them at higher speeds.

An elongated mounting hole on one side of the flange lets you adjust the position of these bearings without having to remove your shaft.

Use these bearings for light loads and small shafts. The closed backing blocks out dust and other contaminants.

The lubricant in these mounted ball bearings is NSF registered H1 and FDA compliant for incidental contact with food.

Permanently lubricated and IP69K certified for washdown environments, these mounted ball bearings are useful for hard-to-reach areas in food, beverage, pharmaceutical, and chemical plants. Mount them using their two-bolt flange.

With all three mounting holes on one side, you can position the bearing above or below the mounting surface.

Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting.

Because they never need to be relubricated, these rollers are a good choice for hard-to-reach places.

Also known as eccentric track rollers, the shoulder adjusts up or down to align to your track, enabling uniform alignment among rollers in a system.

These rollers are rated to handle radial and thrust (top and side) loads simultaneously.

Lubricated with graphite, these rollers can handle temperatures from -450° to 750° F—the widest temperature range of any track roller in our offering.

These threaded track rollers are made of materials that prevent corrosion in wet environments.

Also known as yoke-style cam followers, these rollers have more mounting flexibility than threaded track rollers. They're typically mounted onto a shaft or clevis rod end.

These rollers are rated to handle radial and thrust (top and side) loads simultaneously.

Also known as yoke-style cam followers, these rollers have more mounting flexibility than threaded track rollers. They're typically mounted onto a shaft or clevis rod end.

Also known as eccentric track rollers, the shoulder adjusts up or down to align to your track, enabling uniform alignment among rollers in a system.

Thread the stud directly into a component or secure with a nut for through-hole mounting.