For a longer service life than brass and cast iron valves, these have a durable bronze body.

A cast iron body absorbs vibration from pressure changes to reduce wear and noise in your pipeline.

Often used on dispensers, humidifiers, and fountains, these valves have a 316 stainless steel body that can stand up to deionized water and corrosive conditions.

For extremely high-pressure applications in tight spots, these valves handle the same inlet pressures as other ultra-high-pressure-regulating valves within a smaller footprint.

Valves have a brass body.

Withstand inlet pressures up to 3,500 psi.

Maintain contaminant-free standards in clean room environments. These valves come cleaned and bagged to Fed. Spec. Class 100 and ISO Class 5 clean room standards and have a 316 stainless steel body with a smooth finish to resist dust collection.

Body is cast iron.

For a longer service life than standard valves for cryogenic liquids, these have a durable bronze body. They’re for use with liquid argon, liquid carbon dioxide, liquid nitrogen, and liquid oxygen.

Valves have NPT connections.

For a longer service than cast iron valves, these have a durable bronze body and a 303 stainless steel seal.

These valves have a brass body.

Adjust and maintain the pressure of your compressed air.

Adjust and maintain the pressure of your compressed air.

Adjust and maintain the pressure of your compressed air.

Adjust and maintain the pressure of your compressed air.

An internal check valve permits reverse flow, so these regulators work with double-acting cylinders.

Prevent unauthorized adjustment and unintentional pressure changes with these regulators.

No need to worry about unintentional changes to your pressure setting—these regulators maintain a fixed outlet pressure.

A 316 stainless steel housing allows these regulators to withstand corrosive environments in the semiconductor, marine, chemical, instrumentation, and paper industries.

Mount these regulators to a 35 mm DIN rail or a wall with one of the two included brackets.

At ±0.1% accuracy, use these regulators in sensitive applications where constant, consistent pressure is important.

View and control output pressure remotely and at the source.

Mount these regulators to a 35 mm DIN rail with the included bracket.

Connect two or more of these manifold regulators to meet multiple pressure requirements from a single air supply—set a different output pressure with each regulator.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

A clear polyurethane bowl makes these filter/regulators chemical resistant for use with synthetic compressor oils and cleaning fluids and allows you to see inside to monitor contents.

A stainless steel housing and bowl allow these filter/regulators to withstand corrosive environments in the semiconductor, marine, chemical, instrumentation, and paper industries.

No need for thread adapters—these filter/regulators have an NPT inlet and a BSPP outlet.

A Norgren filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A Wilkerson filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

No need for thread adapters—these filter/regulator/lubricators have an NPT inlet and a BSPP outlet.

Prevent accidental start-up when servicing equipment.

Prevent accidental start-up when servicing equipment.

Prevent accidental start-up when servicing equipment.

Designed to be mounted inline, these valves can be installed in an easy-to-reach location along your line. They control the speed of air-powered equipment by adjusting the volume of airflow.

A fine-adjustment dial allows tighter control of airflow and cylinder speed than other flow control valves. They control the speed of air-powered equipment by adjusting the volume of airflow entering or exiting.

Mount these valves directly to cylinder ports, eliminating additional tubing between the cylinder and valve for better control than inline valves. Made of plastic and stainless steel parts, they have excellent corrosion resistance. They control the speed of air-powered equipment by adjusting the volume of airflow.

Protect air-powered equipment in emergency shut-off situations—when system pressure drops, these valves automatically close to stop cylinder motion, even at mid-stroke. They control the speed of air-powered equipment by adjusting the volume of airflow entering or exiting.

These valves have a muffler to reduce exhaust noise. A padlock locks the handle in the shut-off position so you can disconnect air tools safely.

Also known as blocking valves, these valves allow airflow while an air signal is applied to the air pilot. When the signal stops, the valve closes, trapping air in the system.

Also known as air fuses, these valves close automatically to turn airflow off when air volume exceeds the shut-off flow rate.

Create one action with these valves, such as extending a cylinder.

Control these valves with one hand. Also known as 4/2 valves, they create two actions, such as extending and then retracting a double-acting cylinder.

In the off position, these valves exhaust all air pressure, allowing the equipment to return to the neutral position. Also known as 4/3 exhaust-center valves, they create two actions, such as extracting and then retracting a double-acting cylinder.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/2 valves.

These valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. They create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/3 closed center valves.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 5/2 valves, they actuate when voltage is applied to the electrical connection.

These valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Apply voltage to the electrical connection to actuate.

Also known as 4-way and 5/2 valves, these valves create two actions, such as extending and then retracting a double-acting cylinder. Apply voltage to the electrical connection to actuate.

Also known as 3/3 valves, these valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. They're often used for vacuum suction and release applications and intermediate cylinder stops.

Ceramic plates form a longer-lasting seal against oil and dust than rubber seals that deteriorate over time. These valves withstand use in corrosive, dusty, and dirty environments such as foundries, paper mills, and steel plants. Apply voltage to the electrical connection to actuate.

Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as pilot valves and 4-way valves, they use an air signal to actuate, so they're good for environments where electrical use may be dangerous.

These valves create one action, such as extending a cylinder. Also known as 3/2 or pilot valves, they use an air signal to actuate, so they're good for environments where electrical use may be dangerous.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. They activate when an object, such as a box rolling on a conveyor, pushes the actuator. Also known as 4-way and 5/2 valves.

Also known as 4-way and 4/2 valves, these valves create two actions, such as extending and then retracting a cylinder. Use your foot to operate them, leaving your hands free to perform other tasks.

Control the flow of exhaust air while also regulating the exhaust air speed. These valves dump exhaust air to the atmosphere without routing it back through a directional control valve. The 90° elbow shape allows you to install them in tight spaces. Also known as quick exhaust valves.