Valves have a brass body and NPT connections.

Regulate pressure in air and inert gas systems from your instrument panel—these valves have threads below the adjustment knob and come with a panel-mount nut.

Threads below the adjustment knob and an included panel-mount nut allow you to add these valves to your instrument panel.

Regulate vacuum levels from your instrument panel with these valves that have threads below the adjustment handle and a panel-mount nut.

Less than a quarter of the height of standard pressure-relief valves, these are often installed on tanks in low-clearance areas.

The most basic option for air and inert gas applications.

Adjust and maintain the pressure of your compressed air.

Adjust and maintain the pressure of your compressed air.

An internal check valve permits reverse flow, so these regulators work with double-acting cylinders.

Prevent unauthorized adjustment and unintentional pressure changes with these regulators.

Fit these regulators in tight spaces to adjust and maintain air pressure in sensitive applications where constant, consistent pressure is important.

Use a single air supply to meet the pressure requirements of multiple applications—connect one of these manifolds to your air line, and then set a different output pressure for each station.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

These filter/regulator combinations come as one convenient unit that cleans the air as it regulates pressure.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

A clear polyurethane bowl makes these filter/regulators chemical resistant for use with synthetic compressor oils and cleaning fluids and allows you to see inside to monitor contents.

Two-stage filtration is like getting two filters in one—the first stage removes large particles, while the second removes fine particles.

An ARO filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

An ASCO Numatics filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

Prevent accidental start-up when servicing equipment.

Designed to be mounted inline, these valves can be installed in an easy-to-reach location along your line. They control the speed of air-powered equipment by adjusting the volume of airflow.

Designed to be mounted inline, these valves can be placed in an easy-to-reach location along your line to control the speed of air-powered equipment by adjusting the volume of airflow. A numeric indicator provides a relative measure of airflow, similar to the volume dial on a speaker, so it's easy to set the same flow rate with each use.

A fine-adjustment dial allows tighter control of airflow and cylinder speed than other flow control valves. They control the speed of air-powered equipment by adjusting the volume of airflow entering or exiting.

Mount these valves directly to cylinder ports, eliminating additional tubing between the cylinder and valve for better control than inline valves. Made of plastic and stainless steel parts, they have excellent corrosion resistance. They control the speed of air-powered equipment by adjusting the volume of airflow.

Adjust airflow equally in both directions. These valves regulate the speed of airflow as it enters and exits equipment. They're often used to control the extension and retraction speed of an air cylinder at the same time.

Independently control the speed of airflow in two directions. These valves regulate the speed of airflow as it enters or exits equipment, and are often used to control the extension and retraction speed of an air cylinder at the same time.

Prevent damage to your equipment by limiting startup airflow and then gradually raising the airflow rate to operating levels.

Also known as blocking valves, these valves allow airflow while an air signal is applied to the air pilot. When the signal stops, the valve closes, trapping air in the system.

To prevent accidental start-up, these valves can be locked in their off position with a padlock. They create one action, such as extending a cylinder.

Control these valves with one hand. Also known as 4/2 valves, they create two actions, such as extending and then retracting a double-acting cylinder.

Because they require a key to operate, you can limit who is able to adjust these valves. They create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/2 valves.

These valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. They create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/3 closed center valves.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 5/2 valves, they actuate when voltage is applied to the electrical connection.

In the off position, these valves exhaust all air pressure, allowing the equipment to return to the neutral position. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Apply voltage to the electrical connection to actuate.

Run through equipment cycles up to 30% faster than with standard valves. Also known as 3/2 valves, they create one action, such as extending a cylinder. Apply voltage to the electrical connection to actuate.

Create two actions at the same time, such as extending two single-acting cylinders at once. Apply voltage to the electrical connection to actuate. Also known as pressure center valves.

Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as pilot valves and 4-way valves, they use an air signal to actuate, so they're good for environments where electrical use may be dangerous.

These valves create one action, such as extending a cylinder. Also known as 3/2 or pilot valves, they use an air signal to actuate, so they're good for environments where electrical use may be dangerous.

Also known as 4-way and 4/2 valves, these valves create two actions, such as extending and then retracting a cylinder. Use your foot to operate them, leaving your hands free to perform other tasks.

These valves create one action, such as extending a cylinder. Use your foot to operate them, leaving your hands free to perform other tasks. Also known as 3-way or 3/2 valves.

Quickly vent exhaust air to the atmosphere or divert it to another place in your system to speed up the movement of equipment. The 90° elbow shape allows you to install them in tight spaces. Also known as quick exhaust valves.

Choose the pressure range you need. When these valves receive an air signal, they quickly dump exhaust air to the atmosphere without routing it back through a directional control valve to speed up the movement of equipment. They're often used with air compressors that require continuous operation. Also known as quick exhaust valves.