Use these valves with water, air, and inert gas.

A threaded union on these valves makes them easy to install and remove without disrupting your line.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. They’re for use with water, oil, air, and inert gas.

Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves meet NSF/ANSI 61, which means they’re safe to use with drinking water systems.

These valves meet NSF/ANSI 61 for use in drinking water lines.

For chemical-processing applications in confined areas, these valves have a low-profile handle to fit in tight spots. A rubber seal and a plastic body stand up to aggressive, corrosive solutions.

For fast installation and removal from pipelines, these valves have union fittings that disassemble into multiple pieces. All have a fluoroelastomer seal and a plastic body that can stand up to aggressive and corrosive solutions in chemical-processing applications.

Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves have a fluoroelastomer seal and a plastic body that can withstand aggressive and corrosive solutions in chemical-processing applications.

Barbs grip onto tubing, providing a secure hold. To withstand aggressive and corrosive solutions in chemical-processing applications, these valves have a plastic body and a chemical-resistant seal.

These valves have socket-weld connections for bonding to unthreaded male plastic pipe.

Bond these valves to plastic pipe with PVC primer and cement to create a permanent, leak-tight connection in drinking water lines. Also known as gate valves, they open and close gradually to prevent damage to your system from sudden changes in flow.

These solenoid valves operate on electricity to automatically start and stop flow. The actuator is directly mounted to the valve body to minimize movement and reduce wear.

Lower profile and available in smaller connection sizes than standard valves, these fit in tight spots.

Comparable to Asco Red Hat 8210G Series and Parker Gold Ring 23C Series, these valves meet the highest quality standards.

Less than half the size of our other compact valves, these have small pipe connections for miniature lines.

Designed for controlling single-acting, spring-return air cylinders, these valves have a third threaded port to exhaust media.

Avoid pressure surges and system shocks that can damage piping by installing these valves that open and close slowly.

Use with coolant and detergent such as ethylene glycol or soap solutions.

Reduce your pipeline footprint with these low-profile valves that are about half the size of standard valves for coolant.

Sturdy internal components resist wear for a long service life in applications with frequent cycling.

Designed to withstand the high temperatures and pressures in steam service applications.

These valves have threaded NPT connections.

Safe for automated on/off control in drinking-water systems, these valves meet NSF/ANSI Standard 61.

For applications sensitive to contamination, these valves stop flow without contacting the process media by pressing down on the outside of tubing.

Often used to control single-acting, spring-return air cylinders, these valves have a third threaded port to exhaust media.

Also known as actuated ball valves, these provide higher flow rates than other air-driven valves.

Separate the union fittings on each end of these valves for fast installation and removal from pipelines.

Insert unthreaded pipe into the socket ends and bond with PVC primer and cement to create a permanent, leak-tight connection.

Plastic provides a lightweight and corrosion-resistant alternative to metal. Use with oil. These valves gradually open and close to adjust and regulate flow.

For a lightweight and corrosion-resistant alternative to metal valves, these have a plastic body. To create a permanent, leak-tight connection, insert unthreaded pipe into the socket ends and bond with PVC primer and cement. These valves are for use with oil. They gradually open and close to adjust and regulate flow.

In addition to fluoroelastomer seats that resist a wide range of chemicals, these valves have no metal parts to corrode, so they’re often used for chemical-processing applications in corrosive conditions. All bolt to flanges to adjust and regulate flow in flanged pipelines.

Use these valves with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Barbs grip onto tubing, providing a secure hold. These valves are for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. Designed for use in food and beverage tubing lines, they adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Also known as proportional solenoid valves, these adjust and regulate flow based on the intensity of the electrical signal into the valve.

For a lightweight alternative to metal valves, these have a plastic body. To fit in tight spots, they have a low-profile handle and a short end-to-end length. Valves are for use with water, oil, air, and inert gas. All divert flow between ports.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. All are for use with water, oil, air, and inert gas. They divert flow between ports in tubing lines.

For easy installation and removal from pipelines, all ends on these valves have union fittings that disassemble into multiple pieces. Their fluoroelastomer seal and plastic body can withstand aggressive and corrosive solutions for diverting flow between ports in chemical-processing applications.

To test water quality without interrupting flow, drain a small amount of liquid through the sampling outlet.

Lower profile than other solenoid diverting valves and available in smaller pipe sizes, these valves are often used to automatically divert flow between ports in tight spots. Use them with water, oil, air, and inert gas. All operate on electricity.

Plastic provides a lightweight alternative to metal.

Insert tubing into the fitting—no heat, solder, or flux required.

Visually inspect flow and debris accumulation through the transparent valve body.

These valves open to allow flow in one direction and close when flow stops or reverses.

Visually inspect flow and debris accumulation through the transparent valve body.

Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 5/2 valves, they actuate when voltage is applied to the electrical connection.

These valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Apply voltage to the electrical connection to actuate.

Also known as 4-way and 5/2 valves, these valves create two actions, such as extending and then retracting a double-acting cylinder. Apply voltage to the electrical connection to actuate.

Run through equipment cycles up to 30% faster than with standard valves. Also known as 3/2 valves, they create one action, such as extending a cylinder. Apply voltage to the electrical connection to actuate.

Create two actions at the same time, such as extending two single-acting cylinders at once. Apply voltage to the electrical connection to actuate. Also known as pressure center valves.

Ceramic plates form a longer-lasting seal against oil and dust than rubber seals that deteriorate over time. These valves withstand use in corrosive, dusty, and dirty environments such as foundries, paper mills, and steel plants. Apply voltage to the electrical connection to actuate.

Rated IP69K, these valves withstand high-pressure, high-temperature washdowns. Their smooth design keeps out dust, dirt, and contaminants, making them easier to keep clean. Apply voltage to the electrical connection to actuate.

Mix and match valve styles on one manifold to meet your control needs. Mount multiple valves to a manifold to reduce piping requirements and create multiple actions from a single pressure input.

Also known as solenoid valves, these valves are operated by an electrical signal to turn airflow on or off.

Designed for use in dust-collection systems, these diaphragm valves periodically burst air to knock debris from filters.

Also known as Monday-morning valves, these valves slowly introduce pressure to reduce surge damage during start-up.

Also known as Monday-morning valves, these valves slowly introduce pressure to reduce surge damage during start-up.