A nozzle and hose allow you to dispense directly into your container. For on-site diesel fuel dispensing at construction sites, on boats, and in other environments without electrical hookups, attach these portable pumps to any 12-volt battery.

Operating on a 12-volt battery, these pumps transfer and drain fuel such as gasoline, diesel fuel, and kerosene. Lock the nozzle with a padlock (not included).

Always bond and ground your application for static control. For more information about bonding and grounding, see Sections 1910.106 and 1910.107 of the Federal OSHA Code or see bonding and grounding equipment.

Pumps with metering nozzle record total volume up to 99,999.9 gallons.

These pumps are C-UL listed for Class I, Division 2, Group D for use in environments with flammable gases. Operating on a 12-volt battery, use them to transfer and drain fuel such as gasoline, diesel fuel, and kerosene. They have an automatic shut-off nozzle so they turn off when the tank is full. Lock the nozzle with a padlock (not included).

Always bond and ground your application for static control. For more information about bonding and grounding, see Sections 1910.106 and 1910.107 of the Federal OSHA Code or see bonding and grounding equipment.

Quickly and cleanly transfer oil with no need for an electrical connection, air connection, or manual pumping. These drum pumps come with everything they need to operate.

Add extra stem assemblies to move a single pump head across multiple containers.

Use additional pump heads to transfer oil to multiple locations at once. Pump heads fit all stem assemblies.

To control the exact amount of oil you move, connect a meter.

Add batteries to minimize downtime—swap in a second battery while another charges.

Remove water in locations without power with these battery-operated pumps. They attach to an 18-volt battery. Pumps are gravity fed and require an elevated liquid source to fully fill the pump before turning on. Do not run dry.

This pump has an impact-resistant aluminum housing and handles larger solids than other battery-operated water-removal pumps. Attach it to a 12-volt battery to remove water in locations without power. Pump is gravity fed and requires an elevated liquid source to fully fill the pump before turning on. Do not run dry.

Pipette for hours on end—these ergonomic pipettors maintain even flow with just the push of a button. With a set speed, you can carefully monitor the quantities aspirated and dispensed. Choose from six aspirating and dispensing speeds—dispense as fast as 5 ml per second. Choose a higher speed when working with viscous liquids. An LED display shows your speed and battery status. To ensure contamination-free pipetting, the nose on these pumps is autoclavable.

Transfer eight or more equal samples at once with the push of a button. Compared to manual pipettors, these pipettors dispense using a motor to improve accuracy and reduce fatigue. With an adjustable finger rest and a shape that fits easily in your hand, they’re designed to keep your hand from getting tired. They use air displacement to draw in and push out samples in precise amounts. They’re often used to fill every well on a well plate and for other repeat tasks.

Use the buttons and LCD display to adjust the dispensing volume and select from a variety of functions. You can set these pipettors to mix samples, handle thick and foamy samples, and change speed to slowly dispense gels. When you’re done, tap the ejector button to discard the tip without having to touch it.

Use with universal-fit pipette tips.

Switch between transferring liquids, mixing samples, and separating mixtures with the touch of a button. Compared to manual pipettors, these pipettors dispense using a motor to improve accuracy and reduce fatigue. Their shape is designed for a comfortable one-handed grip, and the finger rest adjusts so you can fine-tune your grasp. Dispense up to 4,000 times on a single charge.

Select the dispensing volume and function using the screen and buttons. You can control the dispensing speed for better dispensing of thick and foamy samples. These pipettors use air displacement to draw in and dispense in precise amounts. They’re color-coded to quickly identify their volume. Use with universal-fit pipette tips. Press the ejector button to dispose of the tip without touching it.

Add a charging stand to recharge batteries when the pipettors aren’t in use. This keeps the pipettors within reach but stored upright to keep your space organized.

Dispense multiple samples with a single press of a button. With a capacity 10 times larger than their manual equivalent, these pipettors are a good choice when you need high-volume, precise dispensing. These pipettors are powered by a motor to ensure consistency and prevent fatigue. Program up to 10 frequently used speeds and intervals on the touch screen. Tap and swipe to make adjustments in real time—even while wearing gloves. When not in use, these pipettors rest in their included mounting bracket.

Attach a tip for repeat dispensing pipettors to get started. These tips have a piston that makes direct contact with a sample to reduce bubbles. This makes them a good choice for thick or frothy liquids. Clip on the tip and the pipettor automatically recognizes the tip's capacity. When you're done, tap the eject button to release the tip without contact.

The charging stand (sold separately) starts charging immediately when you hang the pipettor on it, even with the tip still installed. The stand also keeps the pipettor upright between tasks, preventing liquid in the tip from flowing into the pipettor and causing damage. Connect the stand to a wall outlet using your pipettor's included power cord.

Distribute hand sanitizer with these refillable dispensers. Instead of using a button, they dispense a drop of sanitizer when the battery-powered sensor detects motion, limiting the spread of germs between users.

Wall-mount dispensers have a manual dispensing button for when their batteries run out. A signal light flashes when batteries are running low, letting you know it’s time to replace them. The amount of sanitizer they dispense is adjustable during initial setup and maintenance. These dispensers comply with ADA regulations when properly installed.

Place freestanding dispensers on any flat surface, no mounting or installation required. Put your hands close to the sensor for a small amount of sanitizer, or farther away for a larger amount. These dispensers have a rechargeable battery and come with a charger. Made of corrosion-resistant stainless steel, they’re more durable than plastic dispensers and won’t rust in wet environments. They’re rated IP67 as protected from dust—even in areas with continuous airflow—as well as high-pressure jets of water from washdowns and submersion in up to a meter of water for 30 minutes.

These dispensers help you comply with ADA when properly installed.

For technical drawings and 3-D models, click on a part number.

These dispensers help you comply with ADA when properly installed.

Place your hands beneath this sensor-activated dispenser to release a single squirt of soap. It helps comply with ADA when properly installed.

Place your hands beneath these battery-powered, sensor-activated dispensers to release a single squirt of soap. All have an internal reservoir to hold bulk soap, so no separate cartridge is needed.

Wall-mount dispensers help you comply with ADA when properly installed. Power shuts off when the cover is open.

Place freestanding dispensers on a flat surface wherever you need them, no installation required. Made of corrosion-resistant metal, they won’t rust in wet environments and are more durable than plastic wall-mount dispensers.

Push the buttons on top of nickel dispensers to adjust how much soap is dispensed.

Stainless steel dispensers are rated IP66 as protected from dust—even when there’s continuous airflow—and high-pressure jets of water such as those in washdowns. They use a rechargeable battery and come with a charger. Place your hands close to the sensor for a small amount of soap, or farther away for a larger amount. These dispensers include a small sample of foam soap.

The most mobile respirators in our offering—these powered respirators allow a wider range of motion than supplied-air respirators. The blower straps around your waist to allow unrestricted movement. They’re often used for jobs such as painting and applications where you need to move around. Comfortable to wear for extended periods of time, these respirators don’t press directly against your face. They include a rechargeable lithium-ion battery that powers them for approximately four hours. To alert you to low battery and low airflow, they have an alarm with two distinct sounds that can be heard inside the hood.

Made of Tychem 2000 (formerly known as Tyvek QC), these hoods are chemical resistant. They have two layers: an outer bib for overspray protection and an inner bib that tucks into your clothing for splash protection. Turn the knob to adjust the hood’s ratchet suspension for a personalized fit.

Respirators with a hard hat are best for jobsites where there is a risk of falling objects or an on-site hard hat requirement. The hard hat fits inside the hood.

Harnesses (sold separately) make it comfortable to wear the respirator for long periods by distributing its weight and reducing pressure on your lower back.

Designed with a battery that connects securely to the blower, these respirators prevent sparks that could ignite flammable or combustible particles in the air. They’re CSA certified to meet NEC requirements for use in hazardous locations. Instead of being tethered to an air source, the blower straps around your waist, allowing you to move freely around a space. Use them in areas with high levels of contaminants. A dual-alarm system alerts you to low airflow and low battery life.

Made of Tychem 2000 (formerly known as Tyvek QC), these hoods resist chemicals. They have two layers: an outer bib for overspray protection and an inner bib that tucks into your clothing for splash protection. Turn the knob to adjust the hood’s ratchet suspension for a personalized fit.

Harnesses (sold separately) make it comfortable to wear the respirator for long periods by distributing its weight and reducing pressure on your lower back.