These are also known as tappet wrenches.

One head is angled 60° for access to hard-to-reach fasteners. These are also known as ignition wrenches.

Made of aluminum-bronze that is Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Sized for working on small equipment, these wrenches are 4 1/8" long with a slim head and handle.

The opening shape makes more contact with fasteners for a better grip than standard open-end wrenches. These tools are also known as flare-nut or line wrenches.

Strike the handle with a hammer to break stuck fasteners free. These are also known as slugging wrenches.

The head is offset 45° to provide additional clearance when reaching over obstructions.

The slim heads fit into tight spaces and around thin fasteners.

Made of stainless steel, these wrenches have excellent corrosion resistance.

One head is angled 60° for access to hard-to-reach fasteners. These are also known as ignition wrenches.

Sized for working on small equipment, these wrenches are 4 1/8" long with a slim head and handle.

The opening shape makes more contact with fasteners for a better grip than standard open-end wrenches. These tools are also known as flare-nut or line wrenches.

Fit the thin head and long jaws into narrow spaces.

Press the lever to lock the jaw and keep these wrenches clamped on your work, leaving your hands free.

The handle is covered in plastic for a comfortable grip.

An insulated handle protects against accidental contact with live electrical circuits. These wrenches are tested to 1,000 volts to meet IEC 60900.

Extend the handle for additional reach.

These wrenches are made of stainless steel for excellent corrosion resistance.

Flip the wrench over to use the raised section on the head as a hammer.

Reverse the movable jaw to convert from a smooth-jaw adjustable wrench to a serrated-jaw pipe wrench.

Turn fasteners with the firm grip of a wrench and the adjustability of pliers.

The 25° offset heads give you additional clearance to turn hard-to-reach fasteners.

An extra-long handle provides access to hard-to-reach fasteners and increases leverage.

Ratchet mechanisms allow you to turn fasteners in tight spaces without removing and repositioning the tool.

The head is offset 45° to provide clearance for reaching over obstructions.

Made of aluminum-bronze that is Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant.

The heads are angled to provide clearance around obstructions.

Also known as spud, structural, and construction wrenches, use the pointed end of the handle to align bolt holes during assembly.

The head is offset 45° to provide clearance for reaching over obstructions.

These wrenches are polished for a mirror-like finish.

A ratchet mechanism allows you to turn fasteners in tight spaces without removing and repositioning the wrench.

Reach nuts obstructed by a fluid line or other barrier with the wrench heads in these sets.

Connect one of the heads in these sets to a socket extension to reach an obstructed fastener, then turn the fastener without removing and repositioning the wrench head.

Attach one of these heads to your square-drive ratchet or torque wrench to extend its reach or to access spaces with limited vertical clearance.

Attach one of the heads in these sets to a torque wrench for more leverage to loosen a stubborn fastener.

Slide the open side of these sockets over a tube or hose to adjust a nut that’s already installed.

A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.

These wrenches are made of stainless steel for excellent corrosion resistance.

Flip these wrenches over to ratchet in the opposite direction.

A lever reverses the ratchet direction.

Suitable for occasional maintenance work, these sets are imported.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Pivot the box end for access to fasteners in tight spots.

An extra-long handle provides access to hard-to-reach fasteners and increases leverage.

Made of materials that are Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Flip these wrenches over to ratchet in the opposite direction.

These wrenches are made of stainless steel for excellent corrosion resistance.

Made of materials that are Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant.

Open and close the jaws with one hand. Press the lever and slide the bottom jaw to the desired position; tension keeps it in place.

Insert into a pipe or fitting and turn—the wrench grips the walls for easy installation and removal without marring the outside of the pipe.

Also known as monkey and auto wrenches, these grip large fasteners and other flat objects.

Turn the end of the handle to set torque, and the wrench makes an audible click when it reaches the setting.

Fit these wrenches into slots on the circumference of collars, bearings, and other machine tool components.

Made of aluminum-bronze that is Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

In addition to a long handle, these wrenches include two heads with different hook widths.

The slim profile fits the flanges and nuts on the backing pads of portable sanders and grinders.

Reverse the pins when you need to fit different hole sizes on the face of collars, bearings, and other machine tool components.

Use your ratchet wrench as a handle.

These wrenches are shaped to fit round holes on the circumference of collars, bearings, and other machine tool components.

Sets include various sizes of wrenches that are shaped to fit round holes on the circumference of collars, bearings, and other machine tool components.