We will reply to your message within an hour.
Activate or deactivate your electric water pump based on water pressure. These switches turn your pump off when pressure increases to the set pressure and on when pressure drops to the reset pressure.
Maintain the air pressure needed for air-powered devices. These switches turn your electric air compressor off when it reaches the set pressure and on when it reaches the reset pressure.
With a set pressure range that works for most air systems, these switches send signals when your air system reaches a set pressure to your programmable logic controller (PLC) to activate automated controls and alarms.
The traditional pressure switch. These power equipment, activate controls or alarms, or kick-off other actions when they reach a set pressure.
When these switches reach either of their two set pressures—both of which can be controlled from a display—they send digital signals to your programmable logic controller (PLC) to activate automated controls or alarms.
Compatible with most air systems, these switches send digital signals to a programmable logic controller (PLC) to trigger separate processes when they reach either of their two set pressures. For example, they’ll activate a compressor if the pressure is too low or a relief valve if the pressure is too high.
With multiple ports, these switches maintain the air pressure of your electric air compressor, while also including ports for up to three air-powered devices, reducing the complexity of your air system setup.
Kick off automated controls, signal alarms, or activate equipment based on pressure changes while checking the pressure, setpoint, and reset point on the display.
With a round body that’s at least one-third thinner than traditional pressure switches, these fit in tight, cramped spaces.
Trigger two different automated processes, each with their own set pressure.
Prevent changes to the set pressure that activates equipment—these switches come ready to use at your preferred setpoint.
Choose when these switches reset to control the pressure range between when they activate and deactivate, commonly referred to as deadband and differential.
Used as a safety control, these switches must be manually reset each time they hit the set pressure, so you can inspect equipment before it restarts.
When these switches reach a set pressure, they send electronic signals to your programmable logic controller (PLC) to activate automated controls or alarms.
Cleaned to ASTM G93 requirements and then bagged, these switches meet the strict cleaning standards required for oxygen service lines.
Like other 3-A certified sanitary pressure switches, these switches trigger controls and alarms when food-processing, pharmaceutical, and biotech lines reach a set pressure, but they also have a sanitary adjustable setpoint ring that you twist to make quick changes.
Built with an explosion-proof enclosure to meet NEMA 7 and 9 standards for hazardous locations, these switches were tested and verified by UL and CSA for use where explosive liquids, dust, and gas are present.
Use these switches for applications that need reliable switching but don’t require high accuracy.
Send two digital signals to your programmable logic controller (PLC) to trigger different processes—these switches activate at two set pressures.
With two setpoints and outputs, these switches trigger different actions in your system by sending signals to a programmable logic controller (PLC) when they reach one of their set pressures or vacuums.
Because these switches work with both positive and negative (vacuum) pressures, you can use them in applications that span both.
Designed specifically for air systems, these switches send signals to your programmable logic controller (PLC) to activate controls or alarms when your system reaches a set pressure or vacuum.
When these 3-A certified switches reach a set pressure or vacuum, they trigger controls and alarms in food-processing, pharmaceutical, and biotech lines.
Choose these switches when you need reliable switching but not high accuracy.
The traditional vacuum switch. When these switches reach a set vacuum, they power equipment, signal controls, or trigger alarms.
Specifically made for air systems, these switches send signals to your programmable logic controller (PLC) to trigger processes when they reach a set vacuum.
Trigger two different processes in vacuum applications by sending signals to a programmable logic controller (PLC) when these switches reach one of their two set vacuums. They’re designed specifically for air systems.
Often built into pumps and hydraulic systems with limited space, these compact switches power equipment, activate controls, and signal alarms when they reach a set vacuum.
Control the amount of vacuum change between when these switches activate and deactivate by adjusting when they reset.
Prevent changes to the set vacuum that powers equipment, activates controls, or signals alarms. The setpoint on these switches isn't adjustable.
Often used with ovens, dryers, and HVAC systems, these switches detect small differences in air pressure to indicate a filter is clogged or help you maintain a certain air pressure.
Troubleshoot and monitor the difference in air pressure between two points—these switches have a dial indicator to show differential pressure in real time.
To check the difference in pressure between two points, these switches have a dial indicator that shows differential pressure in real time.
Tested and verified by UL and C-UL for use where explosive dust or gas are present, these switches have an explosion-proof enclosure that meets NEMA 7 and 9 standards for hazardous locations. They are often used to indicate a filter is clogged in a pump or cooling system.
Detect the difference in pressure between two points. For instance, these switches can indicate a filter is clogged in a pump or cooling system.
With an explosion-proof enclosure that meets NEMA 7 and 9 standards for hazardous locations, these switches were tested and verified by UL and CSA for use where explosive gas or dust may be present. Often used with ovens, dryers, and HVAC systems, they can indicate a filter is clogged or help maintain a certain air pressure.
Often used on dispensers, humidifiers, and fountains, these valves have a 316 stainless steel body that can stand up to deionized water and corrosive conditions.
Prevent changes to your pressure setting—these valves come set at a nonadjustable outlet pressure.
Valves have a brass body and NPT connections.
Hook up these valves to equipment with garden hose thread (GHT) connections.
These valves automatically reduce a high, variable inlet pressure to a lower, stable outlet pressure.
A cast iron body absorbs vibration from pressure changes to reduce wear and noise in your pipeline.
To maintain contaminant-free standards in clean room environments, these valves come cleaned and bagged to Fed. Std. Class 100 and ISO Class 5 clean room standards and have a 316 stainless steel body with a smooth finish to resist dust collection.
For a longer service life than brass and cast iron valves, these have a durable bronze body.
Thicker walls and a 304 stainless steel seal make these valves tougher than brass pressure-regulating valves.
Often used in wet conditions and harsh environments, these valves have a 316 stainless steel body for excellent corrosion resistance.
Use this valve in light duty water systems with garden hose thread (GHT) connections.
Change outlet pressure without using a gauge—turn the dial to adjust the outlet pressure in 5 or 10 psi increments.
Excellent performance at low pressures.
Withstand more than six times the inlet pressure of standard pressure-regulating valves.
Rated for more than double the temperature of standard pressure-regulating valves, these can withstand temperatures up to 550° F.
For extremely high-pressure applications in tight spots, these valves handle the same inlet pressures as other ultra-high-pressure-regulating valves within a smaller footprint.
Often used for oxygen service and other high-purity applications, these valves are cleaned and bagged to meet CGA G-4.1 standards to prevent contamination.
Regulate pressure in air and inert gas systems from your instrument panel—these valves have threads below the adjustment knob and come with a panel-mount nut.
Withstand inlet pressures up to 3,500 psi.
A 316 stainless steel body provides exceptional corrosion resistance in wet conditions and harsh environments.
Valves have a brass body.
For easy panel mounting in your water system, these valves have threads below the adjustment knob and come with a panel-mount nut.
Our smallest pressure-regulating valve.
Maintain contaminant-free standards in clean room environments. These valves come cleaned and bagged to Fed. Spec. Class 100 and ISO Class 5 clean room standards and have a 316 stainless steel body with a smooth finish to resist dust collection.
Commonly used for oxygen service and other high-purity applications, these valves come cleaned and bagged to prevent contamination.
These valves automatically reduce a high inlet pressure from compressed gas tanks to a lower, stable outlet pressure.
Often used for pressure-vessel testing and other high-pressure applications, these valves can handle at least seven times the outlet pressure of standard tank-mount pressure-regulating valves.
Designed for nitrogen gas purging in air conditioning, refrigeration, and plumbing systems.
Reduce contaminants in gases used in research sample systems, emission monitoring systems, chromatography, and other high-purity applications. These valves have a 316 stainless steel and brass body with a smooth finish to reduce dust collection and internal components designed to protect the seal and diaphragm from contamination.
Commonly used in TIG welding where gas flow/coverage is a concern.
Flowmeters let you see the gas flow rate from a distance.
Push-to-connect fittings form a low-pressure seal around plastic or soft metal tubing.
Valves have NPT connections.
Compression fittings bite down on hard metal and plastic tubing for a tighter seal than push-to-connect fittings.
Control steam line pressure with ±1 psi accuracy.
Body is cast iron.
For a longer service life than cast iron valves, these have a durable bronze body.
It's like getting four regulators in one—each comes with four springs so you can change between regulating pressure ranges of 2-30, 10-50, 30-90, and 100-180 psi.
A plastic body and fluoroelastomer seal stand up to harsh chemicals.
Regulate air, gas, and liquid pressure on food, beverage, and pharmaceutical lines with these valves—they’re 3-A certified to meet sanitary design standards.
Designed for oxygen service and other high-purity applications, these valves can withstand the extreme cold of liquid argon, liquid carbon dioxide, liquid nitrogen, and liquid oxygen.
Install these valves directly in gas distribution pipelines.
For a longer service life than standard valves for cryogenic liquids, these have a durable bronze body. They’re for use with liquid argon, liquid carbon dioxide, liquid nitrogen, and liquid oxygen.
These valves meet NSF/ANSI 61 for use in drinking water systems.
Choose from valves for liquid argon, liquid nitrogen, liquid carbon dioxide, or liquid oxygen tanks.
For use with acetylene, hydrogen, methane, propane, or propylene gas.
Designed to reduce contaminants in high-purity applications using hydrogen and methane gas, these valves have a stainless steel and brass body with a smooth finish to reduce dust collection and internal components designed to protect the seal and diaphragm from contamination.
Threads below the adjustment knob and an included panel-mount nut allow you to add these valves to your instrument panel.
Use these valves in pipelines.
Designed to meet 3-A sanitary standards, these valves regulate liquid, gas, and air pressure in hygienic zones of food and beverage plants.
These valves have a cast iron body.
For a longer service than cast iron valves, these have a durable bronze body and a 303 stainless steel seal.
For use with low-pressure steam-heating boilers requiring pressure relief at 15 psi, these valves meet ASME Code Section IV.
These valves meet ASME Code Section I for use with steam power boilers requiring pressure relief above 15 psi.
Change set pressure to suit your application—this valve includes four interchangeable color-coded springs with different set pressure ranges.
The most basic option for air and inert gas applications.
For corrosion resistance in wet conditions and harsh environments, these valves have a 303 stainless steel body. All meet ASME Code Section VIII for use with air and inert gas pressure vessels.
Body is brass or nickel-plated brass. All meet ASME Code Section VIII for use with air and inert gas pressure vessels.
Choose these valves for small steam-heating boilers requiring pressure relief between 5 psi and 12 psi.
Commonly used with high-volume blowers, compressors, and air-powered conveyors, these valves quickly relieve a large amount of air in systems with a pipe size of 2 or greater. All meet ASME Code Section VIII for use with air and inert gas pressure vessels.
Commonly used with high-volume blowers, compressors, and air-powered conveyors, these valves quickly relieve a large amount of air in systems with a pipe size of 2 or greater.
These valves have a bronze body for durability and a long service life. All meet ASME Code Section VIII for use with air and inert gas pressure vessels.
With a 316 stainless steel body for exceptional corrosion resistance, these valves are often used in wet conditions and harsh environments. All meet ASME Code Section VIII for use with air and inert gas pressure vessels.
Use these valves with liquid argon, liquid nitrogen, and liquid oxygen.
Our only valves that meet ASME Code Section VIII for use with cryogenic pressure vessels. They are for use with argon, carbon dioxide, helium, hydrogen, methane, nitrogen, and oxygen.
Also known as T & P valves, these open when water temperature reaches 210° F or at the set pressure.
Protect your water-heating system with these valves that meet ASME Code Section IV for hot water heaters and boilers.
These valves meet ASME Code Section VIII for use with water pressure vessels.
Design a valve specifically for your process media and set pressure. Choose from a valve for air, inert gas, water, hydraulic oil, fuel oil, gasoline, or diesel fuel and a set pressure.
With a three-port design, these valves allow inline flow from the inlet to the outlet during normal conditions and divert flow through the relief port in overpressure conditions. They are often used with feed pumps for fertilizers and bleach.
Less than a quarter of the height of standard pressure-relief valves, these are often installed on tanks in low-clearance areas.
Change set pressure without guesswork—the adjustment screw is marked in 25 psi increments for making pressure adjustments without a gauge.
These valves are often used with catalysts, pH buffers, and electroplating solutions.
These valves are commonly used with pumps in low-pressure water systems.
For a low-pressure seal around plastic and soft metal tubing, these valves have push-to-connect fittings.
Alter the set pressure to suit your application.
These valves are often used in hydraulic and lubrication systems.
A finely threaded adjustment screw lets you make precise set pressure adjustments.
Cleaned and bagged for oxygen service and other high-purity applications, these valves are built to withstand the extreme cold of liquid carbon dioxide, liquid nitrogen, and liquid oxygen.
To gradually relieve pressure in lines for diesel fuel, fuel oil, gasoline, and kerosene, these valves begin opening at the set pressure and fully open at about 10% over the set pressure.
Regulate vacuum levels from your instrument panel with these valves that have threads below the adjustment handle and a panel-mount nut.
A lighter and more corrosion-resistant alternative to metal vacuum-regulating valves.
For precise control over your vacuum level, these valves have ±0.1% accuracy.
For a longer service life than brass vacuum-regulating valves, these are made of bronze for strength and durability.
These valves have a brass body.
Vent gases out of your container without letting dust, oxygen, and other contaminants in.
Remotely monitor pressure in general purpose applications such as pumping and compressing systems.
With a pressure range common to most compressed air systems, use these transmitters to monitor your system's air pressure.
Read pressure directly at the source and send data remotely with one device.
Fine-tune the pressure range on these transmitters to account for changes in pressure readings over time.
Adhere to safety standards and monitor pressure when working with high concentrations of oxygen.
Safely monitor liquid, gas, and steam pressure in hazardous locations with these transmitters. They meet NEC safety standards, so they protect against an explosion where flammable gases and vapors are present.
Measure your equipment’s pressure and send the data directly to a development board or single-board computer. Also known as transducers, these transmitters convert pressure into an electrical I2C signal and transmit it to your board.
Choose these transmitters when you need reliable pressure monitoring but not high accuracy.
For use in sanitary applications such as food processing, these transmitters are 3-A certified.
Monitor and control pressure in portable HVAC systems, hydraulics, and oil and gas equipment. Unlike other pressure transmitters that measure the difference between your system and the atmosphere, these transmitters give measurements relative to zero pressure—regardless of altitude or temperature.
These transmitters automatically compensate for error introduced by vibration as well as temperature fluctuations, so you do not need to program your receiving device to correct for these factors. They convert pressure to an electrical signal that can be interpreted by receiving devices, such as remote displays, programmable logic controllers, and motor speed controls to monitor pressure or control equipment.
Remotely track your system's pressure readings from the convenience of a smartphone or tablet. Good for preventative maintenance and route-based monitoring, these battery-powered transmitters use Bluetooth to alert you when equipment requires your attention.
FM approved and CSA certified for use in hazardous locations, these transmitters monitor pressure where combustible fumes may be present.
At least four times as accurate as standard pressure transmitters, these transmitters are ideal for use in laboratories and analytical testing applications.
The diaphragm on these transmitters mounts flush with your system’s connection, leaving no room for thick liquids to clog or harden. They’re often used to monitor pressure in wastewater, paint, and adhesive-dispensing applications.
With a digital display and selectable differential pressure ranges, these transmitters are a versatile alternative to transmitters with dial indicators.
View readings at the source with the dial indicator or remotely using a receiver—these transmitters measure the difference in pressure between two inputs in liquid applications.
Get the flexibility of a differential pressure transmitter and a switch in one. These transmitters can work as a traditional transmitter using an analog output but also have electronic switch outputs and IO Link compatibility, making them great for advanced automation applications.
Check the difference in air pressure between two inputs at the source using the dial indicator or remotely using a receiver.
At least twice as accurate as standard transmitters, these transmitters sense differential pressure at an accuracy of ±0.25%.
Remotely monitor the difference in air pressure between two inputs with these transmitters.
Used with pumps, cooling systems, and other liquid applications, these transmitters remotely measure the difference in pressure between two inputs.
Safe for use in environments where flammable gases and vapors are present, these transmitters measure the difference in pressure between two process lines without needing to program your receiving device to correct for errors. They meet NEC safety standards for protection against an explosion.
Measure the difference in pressure between two process lines without needing to program your receiving device to correct for errors. These transmitters automatically compensate for errors caused by vibration and temperature changes.
These transmitters automatically compensate for error introduced into both pressure and vacuum measurements by vibrations as well as temperature fluctuations, so you do not need to program corrections for these factors into your receiving device. They convert pressure and vacuum to an electrical signal that can be interpreted by receiving devices, such as remote displays, programmable logic controllers, and motor speed controls to monitor pressure or control equipment.
Specifically made for compressed air and gas systems, these transmitters remotely monitor pressure and vacuum.
Convert both pressure and vacuum into an electrical signal that can be interpreted by receiving devices, such as remote displays, programmable logic controllers, and motor speed controls to monitor pressure or control equipment.
With an accuracy of ±0.25%, use these transmitters in applications that require highly accurate measurement of both pressure and vacuum, such as activating vacuum pumps.
Monitor and control vacuum pumps, air compressors, and hydraulics while viewing readings and warnings on the display.
Monitor your system’s pressure and vacuum from a smartphone or tablet via Bluetooth. These battery-powered transmitters send alerts if equipment requires your attention, so they’re good for preventative maintenance and route-based monitoring.
Used in hazardous locations, these transmitters safely convert pressure and vacuum into an electrical signal to measure liquids, gases, and steam. NEC rated for safety, these transmitters are explosion proof, so they can be used in environments containing flammable gases and vapors.
Account for changes in vacuum readings over time by fine-tuning the vacuum range on these transmitters.
At least four times as accurate as standard vacuum transmitters, these transmitters sense vacuum at an accuracy of ±0.25%, making them ideal for use in laboratories and in analytical testing applications.
Convert vacuum into an electrical signal that can be interpreted by receiving devices, such as remote displays, programmable logic controllers, and motor speed controls to monitor vacuum or control equipment.
Designed for compressed air and gas systems, these transmitters remotely monitor vacuum.
Designed for control applications that require high reliability and repeatability, these regulators translate electrical signals to output pressure.
Mount these regulators to a 35 mm DIN rail with the included bracket.
View and control output pressure remotely and at the source.
Keep an eye on the output pressure in high-flow applications—these regulators have a display so you can monitor your application locally.
At ±0.1% accuracy, use these regulators in sensitive applications where constant, consistent pressure is important.
A pressure-calibrated dial allows for easy adjustments to outlet pressure in high-flow applications.
Mount these regulators to a 35 mm DIN rail or a wall with one of the two included brackets.
A 316 stainless steel housing provides superior corrosion resistance and meets NACE (National Association of Corrosion Engineers) material requirement MR-01-75.
Fit these regulators in tight spaces to adjust and maintain air pressure in sensitive applications where constant, consistent pressure is important.
With a greater flow capacity than our standard precision compressed air regulators, use these regulators to adjust and maintain air pressure in sensitive high-flow applications where constant, consistent pressure is important.
Adjust and maintain the pressure of your compressed air.
Cleaned and double bagged in an ISO Class 3 and Fed. Spec. Class 1 clean room for protection from contamination, these regulators are suitable for use in clean rooms.
An internal check valve permits reverse flow, so these regulators work with double-acting cylinders.
Mount these regulators to a 35 mm DIN rail with the included brackets.
Prevent unauthorized adjustment and unintentional pressure changes with these regulators.
No need to worry about unintentional changes to your pressure setting—these regulators maintain a fixed outlet pressure.
A lower profile than our other compressed air regulators makes these regulators a better fit in tight spots.
A 316 stainless steel housing allows these regulators to withstand corrosive environments in the semiconductor, marine, chemical, instrumentation, and paper industries.
Use these regulators to adjust and maintain the pressure of your tubing air lines.
Designed for installation directly to your air-powered tool, these regulators maintain the set air pressure.
Connect two or more of these manifold regulators to meet multiple pressure requirements from a single air supply—set a different output pressure with each regulator.
Use a single air supply to meet the pressure requirements of multiple applications—connect one of these manifolds to your air line, and then set a different output pressure for each station.
Run up to four air-powered tools from a single air supply.
Also known as Monday-morning valves, these valves slowly introduce pressure to reduce surge damage during start-up.
Use a single air supply to distribute air to up to four locations. In addition to the outlet for inline connection, these manifolds have three 1/4 NPT female outlets for connection to air-powered tools and equipment.
Assembled, inspected, and packaged in a clean environment, these filter/regulators come sealed in antistatic double bags.
No need for thread adapters—these filter/regulators have an NPT inlet and a BSPP outlet.
A clear polyurethane bowl makes these filter/regulators chemical resistant for use with synthetic compressor oils and cleaning fluids and allows you to see inside to monitor contents.
Mount these filter/regulators to a 35 mm DIN rail with the included brackets.
With ±0.2 psi accuracy, these filter/regulators provide more precise control than our other compressed air filter/regulators.
A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.
These filter/regulator combinations come as one convenient unit that cleans the air as it regulates pressure.
A stainless steel housing and bowl allow these filter/regulators to withstand corrosive environments in the semiconductor, marine, chemical, instrumentation, and paper industries.
An oil filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.
Two-stage filtration is like getting two filters in one—the first stage removes large particles, while the second removes fine particles.
Prevent accidental start-up when servicing equipment.
No need for thread adapters—these filter/regulator/lubricators have an NPT inlet and a BSPP outlet.
A filter, regulator, and lubricator with push-to-connect fittings are combined to provide clean, lubricated compressed air at your required pressure. Fittings make a tight seal around tubing.
With one outlet port before the lubricator and one after, these filter/regulator/lubricators work in systems that require lubrication in some lines but not in others.
An ARO filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.
An SMC filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.
A filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.
A Norgren filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.
A Parker filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.
A Festo filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.
A Wilkerson filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.
An ASCO Numatics filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.
Ensure sufficient pressure to operate air-powered tools and machines. Pressure boosters compress the air supply, which increases air pressure.
Create a high-flow air stream from your compressed air supply. Flow boosters draw in ambient air, which amplifies compressed air flow.
Use a low-flow air pilot signal with an air supply to produce flow up to 50 cfm to actuate valves and other air-powered system components.
Also known as air fuses, these valves close automatically to turn airflow off when air volume exceeds the shut-off flow rate.
When system pressure reaches the maximum, these valves open and send an air signal to turn on a downstream device such as a discharge valve or throttle. They close and send a signal to turn the device off when pressure drops.
An external nut lets you adjust the pressure without disassembling the valve.
The pressure setting on these valves cannot be adjusted while they are installed.
To set the pressure, unscrew the cap and turn the adjusting screw.
When input pressure varies, use these valves to maintain a consistent pressure.
Set a specific pressure and these valves will maintain it by diverting excess fluid to a tank.
These valves maintain a consistent pressure in a system when input pressure varies.
Set a specific pressure and these valves will maintain it.
Charge these accumulators to the pressure you need.
These accumulators come with a charge of nitrogen and are ready to use.
Use this switch to sense changes in airflow velocity.
Often used to detect clogged air filters and iced air conditioner coils, these switches sense small changes in pressure between two points in your duct.
Also known as an air-to-electric switch, this relay converts an air signal to an electric signal.
Combine a foot-pedal actuator with a switching mechanism to build a complete switch.
Press these switches with your foot for convenient, hands-free operation.
Combine a push-button actuator with a switching mechanism to build a complete switch.
Measure and transmit flow rate, pressure, and temperature of industrial gases, such as air, argon, CO2, and nitrogen, flowing through your system.
Since these switches activate on increasing pressure caused by rising water levels, they have no floats to catch on sump pit walls.
Minimize moisture buildup in enclosures. Also known as drain plugs, these breather vents have a small outlet that allows condensation to drain.
These breather vents withstand corrosion in damp environments.
These breather vents are rated NEMA 6 to withstand periodic submersion in water.
Protect against excess vacuum and pressure in cylinders, gear boxes, enclosures, manifolds, and tanks.
Shield outdoor pipe and tank openings from the environment. Also known as vent caps, these breather vents have screens to allow air flow while blocking debris.
Secure access to vented openings in pipe and tanks—the cap can be locked to prevent tampering.
Keep moisture, dirt, and debris from entering your oil reservoirs.
Add a filling port to your hydraulic tank while protecting against excess pressure and vacuum.
Use these vents to maintain consistent pressure as temperatures fluctuate by allowing air to flow through sealed enclosures.
Safe for use around flammable and combustible gases, vapors, fibers, and dust, these vents allow air to flow through enclosures to maintain consistent pressure and reduce moisture buildup as temperatures change. They also stand up to washdowns.
These vents maintain air pressure inside enclosures that may be exposed to indoor and outdoor temperature changes while keeping dust and water out.
No threaded hole or tools needed—snap these vents into enclosures with a maximum 1/8” panel thickness to let airflow in and keep water out even when submerged.
Rated NEMA 4X, these vents provide protection from washdowns, corrosion, and power jets of water.
These vents have louvers with foam filters to keep out dust and falling liquids.