We will reply to your message within an hour.
The holes are already punched in these strips for convenient installation.
Cut to the length you need with shears or a utility knife and punch holes for hanging.
Often hung in freezers, these strips can be used in food-service environments.
Cut these strips to the length you need for hanging in freezer doorways or other cold environments.
Sized to fit short openings.
These door strips have bumpers to prevent scratches, keeping them clear over time so you can see what’s on the other side and avoid collisions.
These strips are ribbed to hide scratches and wear; cut them to length with shears or a utility knife and punch holes for hanging.
Able to handle temperatures up to 500° F, these door strips can be used near ovens and furnaces.
These ribbed door strip rolls hide scratches and wear and can be used in food-service environments.
Cut these partially light-blocking strips to the length you need and punch holes for hanging.
These partially light-blocking strips can be used to replace worn strips or create custom strip doors.
Replace worn strips or create a custom door with these individual strips. They completely block light to maintain darkness and privacy.
Completely block light with these strip rolls. Cut them to the length you need and punch holes for hanging.
Hang these strips near data centers and other areas where static build-up could harm sensitive electronics.
Cut these strips to the length you need to hang doors for data centers and other areas where static build-up could harm sensitive electronics.
Allow personnel and vehicles to move freely through doorways while keeping heated or cooled air in and dirt, dust, and debris out.
Create custom doors that allow vehicles and people to move freely, while keeping heated or cooled air in and dirt, dust, and debris out.
Often hung in freezers, these doors can be used in food-service environments.
The strips on these doors have bumpers to prevent scratches, keeping them clear over time so you can see what’s on the other side and avoid collisions.
Use these doors in data centers and other areas where static build-up could harm sensitive electronics.
These strip doors partially block light.
Completely block light to maintain darkness and privacy, while allowing traffic to flow freely.
Sized to fit short openings, these strip doors are often used with conveyors to prevent the loss of heated or cooled air through unprotected openings.
Select these doors when complete visibility is important.
These doors open only as much as needed, making them good for cold storage areas.
Maintain the temperature in cold storage or other areas—these doors bend to open only as much as needed.
Made of impact-resistant polyethylene with bumpers on both sides, these doors withstand forklift traffic as well as refrigeration and washdown environments.
Bumpers on both sides protect these doors from forklift traffic. The polyethylene plastic holds up in refrigeration and washdown environments.
These panels are made of UV-resistant plastic and have a gasket to create a tight seal.
These rectangular panels have gaskets that form a tight seal to keep out dust and moisture.
Designed for use with circular cutouts, these panels have gaskets that form a tight seal to keep out dust and moisture.
Add panels to T-slotted framing to create machine guards and strip doors.
Design your own partitions, add to your existing partition, or replace individual components and hardware.
Use one of these kits to replace rusty or broken hardware on urinal partitions.
Replace rusty or broken hardware on your toilet partitions without needing to buy the entire component.
These kits include all brackets and fasteners needed for mounting partitions.
Designed to wrap around the edge of the partition frame, these hinges provide a stronger hold than other toilet partition door hinges.
Create battery-powered, hand-held devices such as card and signal readers—these enclosures have a clear cover for checking screens and status lights inside.
The unique shape of these enclosures provides a handle to hold scanners, detectors, and remote switches.
Protect tablet computers, touch displays, and readouts in these specially sized enclosures. They are rated IP65 for protection from spraying water.
A 9-volt battery fits inside a compartment in these enclosures to power testing devices and other hand-held instruments.
These enclosures shield electrical components from water, so they’re safe to install onto DIN rail in wet and washdown environments.
House emergency stop buttons, life safety equipment, and other devices that need to be seen with these brightly colored enclosures, which are easy to spot even in high-dust areas.
Protect monitors and televisions from environmental damage with these enclosures.
Mounting feet make attachment to machines and walls hassle-free.
Control access to these enclosures with a key-operated lock.
Made of polycarbonate, these enclosures resist denting, chipping, and cracking better than stainless steel enclosures.
View all sides of your installed components.
PVC enclosures are nonconductive and chemical resistant, withstanding solvents, alkalies, and acids.
Mounting feet make attachment to machines and walls hassle-free. These enclosures are small and lightweight for use with sensors, switches, testing devices, and circuit boards.
Internal mounting bosses or mounting brackets enable you to use panels or DIN rail to mount components. These enclosures have a clear cover, so you can inspect components without opening the enclosure.
Internal mounting bosses enable you to attach panels or DIN rail inside the enclosures using self-tapping screws. Made of polycarbonate, these nonconductive enclosures resist denting, chipping, and cracking.
Internal mounting bosses or mounting brackets enable you to use panels or DIN rail to mount components. Enclosures are made of nonconductive polycarbonate that resists denting, chipping, and cracking.
Made of polycarbonate, these enclosures resist denting, chipping, and cracking.
Inspect components without opening the cover.
Made of nonconductive polycarbonate, these enclosures withstand prolonged submersion in water while protecting electronics from dents, chips, and cracks. A clear cover lets you monitor the inside without opening them.
Check on the contents inside these enclosures from every angle without opening them in wet environments.
Mount these enclosures directly to machine control panels in wet environments and view the contents without opening them.
Install these enclosures on control panels and walls and inspect what’s inside without exposing their contents in wet and outdoor locations.
Holes in the cover allow easy installation of push buttons, switches, and indicating lights.
Internal mounting bosses or mounting brackets enable you to use panels or DIN rail to mount components.
Fasten these enclosures to machine control panels or walls without exposing the contents to wet and oily environments.
Made of nonconductive polycarbonate, these enclosures withstand prolonged submersion in water while protecting electronics from dents, chips, and cracks.
Protect keypads, push-buttons, and other handheld controls with these round enclosures that are more comfortable to hold than square enclosures.
Suitable for installing in the ground or for use in wet environments, these direct burial enclosures are rated NEMA 6P for protection from dirt, washdowns, corrosion, and water submersion.
These enclosures withstand temperatures up to 475° F.
These enclosures allow you to inspect your electronics without opening the cover.
Small and lightweight, these enclosures are used with sensors, switches, and testing devices.
Keep electronics safe from harmful contact with hands and tools while still allowing air and moisture to enter.
Two separate chambers allow you to access wiring connections in the lower section without disturbing components that you install in the upper section.
Often used to house emergency-stop buttons, switches, and lights, these bright yellow enclosures are easy to spot, even in dimly lit areas. All have standard-size push-button holes to save time—no need to measure and cut your own holes.