Wider than our standard ball bearings, these rugged bearings are good for handling heavy loads at low speeds.

With a spherical raceway and two rows of balls, these bearings compensate for shaft misalignment.

Internal locking elements (sprags) lock to transmit torque in one direction while turning freely in the other direction.

These 316 stainless steel bearings are more corrosion resistant than our other stainless steel bearings, but they have a lower load capacity.

With two rows of balls, these lightweight bearings have greater durability and load capacity—and a wider profile—than single-row plastic bearings.

The flange ensures proper positioning inside a tube or housing.

Slip these bearings onto a shaft and secure with the included set screws, no special tools required.

Unlike other ball bearings, these do not need to be fully inserted into a housing. A spline around the outside of the bearing creates a permanent, secure hold in thin panels.

A combination of stainless steel and nylon components provide increased corrosion resistance over standard thrust ball bearings.

An ABEC-7 rating means these bearings are made to some of the tightest tolerances, so they operate at the highest speeds.

The needles in these bearings roll freely in one direction, but lock to transmit torque when the rotation of the shaft is reversed. Also known as drawn-cup roller clutches.

With cylindrical rollers to distribute load over a large surface area, these bearings are often used to support heavy loads at high speeds in applications such as power generation and metal recycling.

Cylindrical-roller thrust bearings handle higher loads than needle-roller thrust bearings. They also run at faster speeds than tapered-roller thrust bearings.

The lubricant in these mounted ball bearings is NSF registered H1 and FDA compliant for incidental contact with food.

Use these bearings in corrosive environments and under water.

Use these bearings in corrosive environments and under water.

With all three mounting holes on one side, you can position the bearing above or below the mounting surface.

A double-sealed ball keeps out dirt and debris, and side vents expel contaminants.

Unlike most ball transfers, which have metal balls, these have a plastic outer ball that rolls on stainless steel inner balls, so there's no metal-on-metal contact that could create and release particles into your clean room. They've also been ultrasonically cleaned and then individually bagged to prevent dust contamination.

These ball transfers have capacities up to 3,300 lbs.

With a ball recessed into the mounting surface, these ball transfers have a low profile. Their double-sealed ball keeps out dirt and debris, and side vents expel contaminants.

To keep out dirt and debris, these flange-mount ball transfers have a double-sealed ball and side vents that expel contaminants.

A large-diameter rubber ball handles delicate or polished surfaces. The stem spins and the ball rotates around the stem.

Sleeve bearings ride directly on the axle and have no moving parts to wear out.

Designed to handle heavy loads, these bearings have the highest load capacities of any mounted linear ball bearings we offer.

Designed to handle heavy loads, these bearings have higher load capacities than comparable standard mounted linear ball bearings for support rail shafts.

Outdoor as well as mild chemical environments are no problem for these bearings. They have stainless steel balls for corrosion resistance.

Designed to handle heavy loads, these bearings have higher load capacities than comparable standard linear ball bearings.

Designed to handle heavy loads, these bearings have higher load capacities than comparable standard linear ball bearings for support rail shafts.

Also known as nylon 6/6, this general purpose material is often used for bearings, gears, valve seats, and other high-wear parts.

Practically nonabsorbent, HDPE won't swell when exposed to moisture. It is denser and more rigid than LDPE, plus it's more chemical resistant.

Known for its naturally slippery surface, PTFE surpasses most plastics when it comes to chemical resistance and performance in extreme temperatures.

At only half the weight of glass, polycarbonate maintains excellent impact resistance across a wide temperature range. It's comparable to Lexan, Hyzod, Tuffak, and Makrolon.

A plastic cage surrounds the ball bearings and keeps them from colliding, so these carriages run for many cycles without needing maintenance.

Run many cycles in tight spaces before replacing or re-greasing carriages.

Nylon rollers and aluminum rails make these good for light duty applications.

Create a self-aligning carriage and guide rail system to compensate for mounting surfaces that aren't parallel.

Create your own positioning table or telescoping slide. Sets include four rails, two roller bearing cages, and eight end stops.