We will reply to your message within an hour.
Connect and disconnect with the power on—spring-loaded contacts open like a switch when separating the connectors, preventing an electrical arc.
Caps are watertight to protect safe-break plugs when not in use.
These connectors meet international standards IEC 309-1 and 309-2. They prevent an electrical arc when separating mated connectors, so you can safely connect and disconnect with the power on.
Use connectors where ignitable gas and dust may be present, such as in refineries and silos. They also prevent an electrical arc when separating mated connectors so you can safetly connect and disconnect with the power on.
Caps are watertight to protect hazardous location safe-break plugs when not in use.
Meet international standards IEC 309-1 and 309-2.
When used together, connectors maintain a watertight and corrosion-resistant NEMA 4X connection.
A current rating up to 400 amps makes these connectors suitable for use in industrial machinery and floodlights.
Protect high-current connectors when not in use.
Often used to send power and signal to automated systems, motors, and pumps, these mini connectors carry higher currents than M5, M8, and M12 connectors.
With a PVC housing, connectors withstand exposure to chemicals, oil, fuel, and salt water.
These connectors have the same pin and socket configuration as connectors that meet MIL-DTL-26482, so they can be used with products that meet the same standard. Quickly mate them by pushing them together.
Configure a connector for your application—combine inserts for power and signal with a base and a hood.
Reduce the likelihood of slips and falls in high-traffic areas—connectors won't roll when stepped on.
These general purpose M23 connectors send power or signal to servomotors, servocontrollers, and servodrives.
Each set includes one plug and one socket. These connectors withstand moisture, harsh engine fluids, and high temperatures. Also known as weather-pack connectors.
Also known as power-pole connectors, these single-pole connectors join two pin connections, rather than a pin and socket. They stack from the top and sides to form any configuration.
Couple these adapters with a cord that matches your outlet and length requirements to run DC-powered electronics.
To run DC-powered lab and medical equipment from your outlet, add a power cord with the plug style and length you need. These adapters meet strict IEC, UL, or ANSI/AAMI standards for use with medical devices.
Connect multiple M8 and M12 cords to create a network between equipment. These blocks are often used to send signal and power to proximity switches and sensors.
Often used for automated systems, motors, and pumps in tough industrial areas such as near welding and metal machining, these cords carry higher current than M5, M8, and M12 cords.
Send power from generators to keep the lights on and equipment running.
The ratchet applies the correct pressure to ensure a complete crimp every time on pin-and-sleeve contacts.
The ratchet applies the correct pressure to ensure a complete four-point crimp every time to adhere to strict MIL-C-22520/1 standards.
Crimp pin-and-sleeve contacts in connectors.
Adapt 10-pin cables for connection to a USB port on a PC.
Convert 10-pin cables to RS-232C for connection to PCs.
Add these connectors to thermocouple wire for easy attachment to thermometers and control panels.
Connect multiple thermocouple probes to an instrument panel.
Convert round-pin thermocouple male connectors to flat-pin thermocouple male connectors.
Also known as feedthrough connectors, these mount through threaded tank openings to make connections between thermocouple probes and external equipment.
Plug thermocouple probes into a control panel.
Extend the reach of your thermocouple probe—plug-in connectors on both ends of this wire speed up installation.
Attach plug-in connectors to RTD probes with wire leads.
Plug your microphone into an amplifier or speaker.
Connect these lifters to your robot arm to pick up and move items using suction. They're electric, so you don't need a compressed air source.
Use these cords to connect PLC expansion modules and keep everything configured on one processor.