The toughest bits available, these withstand the shock and twisting force of impact drivers.

Ribs forged into the wings of these bits grip the screw recess to reduce stripping. They're also known as ACR® bits.

A wide tip makes good contact in shallow and coated screw recesses, such as those filled with paint.

Drive screws with both ends of these bits. Use with hand drivers.

Remove screws in hard-to-reach places. A spring-loaded sleeve guides bits onto the screw head and keeps them from slipping out.

These bits provide a secure grip on the Phillips/slotted combination-drive screws in electrical equipment.

While screws with a Square/Phillips combination drive can be turned with either a Square or Phillips bit, these make the best contact so you can apply high torque without slipping and stripping the recess. They are also known as Quadrex bits.

Less likely to crack or shatter under high torque than standard bits, these are often used with power tools to install machine screws.

The knurled shank on these bits allows finger tightening. They can also be used with the included screwdriver.

Sets include an assortment of drivers.

When working in tight spaces, these short drivers fit where others can't.

Sets include an assortment of drivers with a suede-like textured handle that provides a firm grip, even for oily hands.

These screwdrivers have a soft, contoured handle that provides comfort and the best possible grip for achieving maximum torque.

Sets include an assortment of drivers with a cushioned grip that provides comfort and some slip resistance.

A cushioned grip over a plastic core adds comfort and some slip resistance.

Reduce slipping and stripping the screw recess. The tip of these drivers has ribbed grooves that grip the surface of the recess, minimizing the pressure required to achieve maximum torque.

Carry these slim-handled tools comfortably in your pocket.

Bright-colored handles make these tools stand out so they're less likely to be misplaced.

When working at heights, secure a lanyard to the ring on these tools to prevent drops. The ring rotates around the shaft so the driver turns freely.

A shaft that extends through the handle and a steel end cap gives these drivers the strength to absorb hammer blows.

The handle on these assorted drivers drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment. They're also known as ESD-safe screwdrivers.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC, EN, or ASTM standards.

Protect your stainless steel screws by using a stainless steel driver. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These drivers eliminate that risk.

For use in applications where a magnetized tool can cause damage, these screwdrivers have a titanium shaft.

Made of beryllium copper that is FM approved, these screwdrivers help meet OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

When working in tight spaces, these short drivers fit where others can't. Bits have a different tip at each end and snap into the shaft, which is also a nutdriver.

Drive screws four times faster than ratcheting alone. Grip the speed housing at the base of the shaft with one hand while turning the handle with the other. A magnet at the end of the shaft holds bits in place.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet EN 60900 and IEC 60900.

Insert a bit into the shaft and a magnet holds it in place.

Operate these tools like a standard bit driver and access hard-reach fasteners with the offset head. Insert a bit and a magnet holds it in place.

Press down on the handle’s collar to either adjust the shaft length or remove the shaft and replace it for a different tip. Sets include a handle and multiple reversible shafts.

These assorted screw starters have a slim body that reaches into tight spots to grip and turn screws that are hard to reach or too small to hold by hand.

The tips are offset 90° to provide additional clearance when reaching over obstructions to turn fasteners.

Sets include an assortment of drivers with a tip that can be replaced when it becomes worn. Press the rotating end cap on the handle with your palm to apply constant pressure to small fasteners while turning the body of the screwdriver with your fingertips.

A magnetized tip holds the screw in place. Press the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Sets include an assortment of drivers with a rotating end cap on the handle that allows you to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

The assorted drivers in these sets have an insulated handle and shaft that protect against shock from accidental contact with live electrical circuits. They are tested to 1,000 volts to meet IEC, EN, or ASTM standards. Use the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

The handle on these assorted ESD-safe screwdrivers drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment. Press the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Set includes a handle and six shafts. Remove and replace the shaft to use a different size or drive style.

The short Phillips bit on these sockets fits in spaces that screwdrivers can’t and where height clearance is limited.

Keep a convenient variety of drive styles and sizes of bit sockets on hand.

Slide a different shaft into a handle to change tip size or drive style.

What you need for most maintenance jobs, these sets include an assortment of drivers, cutters, pliers, and wrenches.

Made of materials that are Factory Mutual approved, these tools inhibit sparking and are nonmagnetic and corrosion resistant.