About Sealant Flexibility
More
About Paint and Protective Coatings
More
Wear-Resistant Coatings for Metal
Also known as brushable ceramic, these coatings create a hard, low-friction surface that resists corrosion. They're often used on liquid processing equipment, such as pump casings, impeller blades, and valves, to protect worn areas and reduce turbulence. They’re also used on heat exchangers, condensers, and chutes. The size listed is the combined total of the two parts.
Devcon Brushable Ceramic resists acids, alkalies, fuels, and solvents. Apply with a brush or roller.
Container | Dry Time | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Net Weight, lbs. | Composition | Touch, min. | Overall, hrs. | Approx. Coverage @ Thick. | Application Time After Mixing, min. | Max. Temp., °F | Application Temp. Range, °F | For Use On | Color (Appearance) | Each | |
Devcon Brushable Ceramic Coatings | ||||||||||||
11765 | 2 | Solvent Based | 40 | 16 | 15 sq. ft. @ 20 mil | 40 | 350° | 55° to 90° | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | Blue (Gloss) | 00000000 | 0000000 |
Epoxy Potting Compounds for Harsh Environments
Tough enough to be permanently submersed in seawater, these compounds protect sensitive electronics, such as circuit boards, semiconductors, and sensors in harsh environments. They resist moisture, salt, and chemicals, so you can use them in corrosive oil, marine, and mining applications. These compounds can also be used within autoclaves. Because they are epoxies, they are rigid, resist wear, and create excellent electrical insulation. They withstand a wide range of temperatures, and this formulation won’t crack or split as components heat up and cool down.
They come in a cartridge, so you can apply them precisely. To dispense, they require a mixer nozzle and gun (both sold separately).
Dry Time | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
Container Size, fl. oz. | Consistency | Touch, hrs. | Overall, hrs. | Hardness Rating | Dielectric Strength, V/mil | Temp. Range, °F | Environment | For Use On | Autoclavable | Each | |
1.69 | Thick Liquid | 12 | 24 | Extra Hard | 500 | -50° to 350° | Corrosive, Salt Spray, Submersible | Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Polystyrene Plastic, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PVDF Plastic, Polyimide Plastic, HDPE Plastic, Nylon Plastic, PEEK Plastic, Polyethylene Plastic, UHMW Plastic, Polypropylene Plastic, Glass | Yes | 0000000 | 000000 |
For Cartridge Size | Each | |
1.69 fl. oz. | 00000000 | 000000 |
For Cartridge Size | Each | |
1.69 fl. oz. | 00000000 | 00000 |
Optically Clear Epoxy Potting Compounds
Clear enough to read through, these UV-resistant potting compounds allow optimal light transmission for use with LEDs, solar cells, and fiber optics. Use them to encase electronic assemblies for protection from dust, chemicals, moisture, mechanical shock, and vibration. Rigid and wear resistant, epoxies are the strongest of the potting compounds. They have excellent chemical and moisture resistance, withstand a wide range of temperatures, and provide excellent electrical insulation. All require a mixer nozzle and gun to dispense.
Dry Time | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
Container Size, fl. oz. | Consistency | Touch, min. | Overall, hrs. | Dielectric Strength, V/mil | Thermal Conductivity, W/m-K | Temp. Range, °F | For Use On | Color | Each | |
Optically Clear Epoxy Potting Compounds—Extra Hard | ||||||||||
1.7 | Thick Liquid | 40 | 24 | 229 | 0.45 | -65° to 275° | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Iron, Silver, Plastic, Rubber, Composites, Fiberglass, Ceramic, Glass | Amber | 0000000 | 000000 |
Two-Part Adhesive Dispensing Guns | |||
---|---|---|---|
Dispensing Gun for 1.7 fl. oz. Cartridges | 00000000 | Each | 000000 |
Heat-Transfer Potting Compounds
Formulated to draw heat away from sensitive electronic components, these potting compounds have higher thermal conductivity than standard potting compounds. Use them to encase electronic assemblies for protection from dust, chemicals, moisture, mechanical shock, and vibration. Rigid and wear resistant, epoxies are the strongest of the potting compounds. They have excellent chemical and moisture resistance, withstand a wide range of temperatures, and provide excellent electrical insulation.
Dry Time | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
Container Size, fl. oz. | Consistency | Touch | Overall, hrs. | Dielectric Strength, V/mil | Thermal Conductivity, W/m-K | Max. Temp., °F | Heating Requirements to Reach Full Strength | For Use On | Color | Each | |
0.9 | Thick Liquid | 25 min. | 24 | 450 | 1.87 | 500° | 1 hr. @ 250° F then 1 hr. @ 350° F | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Iron, Silver, Titanium, Plastic, Composites, Ceramic, Glass | Black | 0000000 | 000000 |
1 | Gel | 4 hrs. | 6 | Not Rated | 1.87 | 600° | 4 hrs. @ 250° F then 2 hrs. @ 350° F | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Iron, Silver, Titanium, Plastic, Composites, Ceramic, Glass | Black | 0000000 | 00000 |
1.5 | Thin Liquid | 30 min. | 26 | 450 | 0.59 | 500° | 1 hr. @ 250° F then 1 hr. @ 350° F | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Iron, Silver, Titanium, Plastic, Composites, Ceramic, Glass | Amber | 0000000 | 00000 |
Dry Time | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Container Size, fl. oz. | Consistency | Touch | Overall, hrs. | Mix Ratio | Tensile Strength, psi | Dielectric Strength, V/mil | Thermal Conductivity, W/m-K | Max. Temp., °F | Heating Requirements to Reach Full Strength | For Use On | Color | Each | |
16 | Thin Liquid | 30 min. | 26 | 6:1 | 9,500 | 450 | 0.59 | 500° | 1 hr. @ 250° F then 1 hr. @ 350° F | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Iron, Silver, Titanium, Plastic, Composites, Ceramic, Glass | Amber | 0000000 | 0000000 |
Harsh Environment Coatings for Electronics
High humidity, harsh chemicals, water submersions, and salt are no match for these electronic coatings. They also resist UV light, so they’ll work outdoors. Use them on circuit boards, sensors, and LED drivers in heavy machinery. Also known as conformal coatings, they’re thinner than potting compounds, so they flow into the smallest contours of your components to cover them completely.
PVDF coatings are more flexible than epoxy coatings. They’re IPC certified for use on circuit boards. You can also use them to protect against corrosion on metal joints. To apply, brush or spray them on, or dip your components in.
Epoxy coatings resist impact and wear better than PVDF coatings, and they work in higher temperatures. You can also use them as an adhesive. For controlled pouring, they’re thickened with silicate. These coatings are autoclavable, and they’ll even cure underwater. Dispense them with a mixer nozzle and a gun (each sold separately).
Dry Time | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Container Size, fl. oz. | Consistency | Touch | Overall | Mixing Required | Mix Ratio | Mixer Nozzle Included | Dielectric Strength, V/mil | Thermal Conductivity, W/m-K | Temp. Range, °F | Specifications Met | For Use On | Color | Autoclavable | Each | |
PVDF Plastic Coatings—Hard | |||||||||||||||
Bottle | |||||||||||||||
1 | Thick Liquid | 5 min. | 30 min. | No | __ | __ | 750 | 0.2 | -65° to 255° | IPC-CC-830 | Aluminum, Brass, Bronze, Steel, Stainless Steel, Titanium, Cast Iron, Iron, Silver, Plastic, Rubber, Composites, Fiberglass | Clear | Yes | 0000000 | 000000 |
Epoxy Coatings—Extra Hard | |||||||||||||||
Cartridge | |||||||||||||||
1.69 | Thick Liquid | 12 hrs. | 24 hrs. | Yes | 2:1 | No | 500 | Not Rated | -50° to 350° | __ | Aluminum, Brass, Bronze, Steel, Stainless Steel, Titanium, Cast Iron, Iron, Silver, Plastic, Rubber, Composites, Fiberglass | Clear | Yes | 0000000 | 00000 |
For Cartridge Size | Each | |
1.69 oz. | 00000000 | 000000 |
For Cartridge Size | Each | |
1.69 oz. | 00000000 | 00000 |
Heavy Duty Heat-Transfer Coatings for Electronics
This thermally conductive coating keeps electrical components cool by dissipating heat. Use it to bond transformers, transistors, and other heat-generating components to printed circuit boards and heat sinks.
Dry Time | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
Container Size, fl. oz. | Consistency | Touch, min. | Overall, hrs. | Dielectric Strength, V/mil | Thermal Conductivity, W/m-K | Temp. Range, °F | For Use On | Color | Each | |
1 | Paste | 5 | 2 | 750 | 0.864 | -85° to 347° | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Iron, Silver, Plastic, Rubber, Composites, Fiberglass | White | 0000000 | 000000 |
Surface Fillers
These surface fillers can be used on vertical surfaces without sagging. They repair cracked, worn, and damaged surfaces. The size listed is the combined total of the two parts.
Devcon Metal Patch & Fill repairs worn, rusted, and corroded surfaces with less preparation.
Surface fillers in one-time-use packets are also known as double-bubbles.
Container | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Size | Net Weight | Type | Begins to Harden, min. | Reaches Full Strength | Consistency | Mix Ratio | Approx. Coverage @ Thick. | Temp. Range, °F | Color | Finishing Method | For Use On | Pkg. Qty. | Pkg. | |
Loctite® Fixmaster Epoxy | |||||||||||||||
EA 445 | __ | 0.12 oz. | Mixer Cup | 5 | 12 hrs. | Thick Liquid | 1:1 | 1 sq. in. @ 1/4" | -65° to 180° | Gray | Machine, Sand, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, ABS Plastic, CPVC Plastic, PETG Plastic, Polycarbonate Plastic, Polyimide Plastic, Polystyrene Plastic, Polyurethane Rubber, PVC Plastic, PVDF Plastic, Ceramic, Concrete, Glass, Wood | 10 | 0000000 | 000000 |
EA 445 | __ | 1 oz. | Mixer Cup | 5 | 12 hrs. | Thick Liquid | 1:1 | 1 sq. in. @ 1/4" | -65° to 180° | Gray | Machine, Sand, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, ABS Plastic, CPVC Plastic, PETG Plastic, Polycarbonate Plastic, Polyimide Plastic, Polystyrene Plastic, Polyurethane Rubber, PVC Plastic, PVDF Plastic, Ceramic, Concrete, Glass, Wood | 10 | 0000000 | 000000 |
EA 9131 | __ | 0.12 oz. | Mixer Cup | 90 | 24 hrs. | Thick Liquid | 1.5:1 | 1 sq. in. @ 1/4" | -65° to 180° | White | Machine, Sand, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, ABS Plastic, CPVC Plastic, PETG Plastic, Polycarbonate Plastic, Polyimide Plastic, Polystyrene Plastic, Polyurethane Rubber, PVC Plastic, PVDF Plastic, Ceramic, Concrete, Glass, Wood | 10 | 0000000 | 00000 |
Each | |||||||||||||||
Loctite® Fixmaster Poxy Pak™ | |||||||||||||||
EA 9017 | 0.8 fl. oz. | __ | Syringe | 5 | 60 min. | Thick Liquid | 1:1 | Not Rated | -65° to 300° | Clear | Sand | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, ABS Plastic, CPVC Plastic, PETG Plastic, Polycarbonate Plastic, Polyimide Plastic, Polystyrene Plastic, Polyurethane Rubber, PVC Plastic, PVDF Plastic, Concrete, Glass, Wood | __ | 0000000 | 00000 |
Devcon Metal Patch & Fill | |||||||||||||||
S-50 | 3 fl. oz. | __ | Tube | 20 | 6 hrs. | Paste | __ | 6 sq. in. @ 1/4" | 40° to 400° | Gray | Drill, Sand | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Ceramic, Glass | __ | 00000000 | 0000 |
Pkg. | |||||||||||||||
Surface Fillers | |||||||||||||||
__ | __ | 0.1 oz. | One-Time-Use Packet | 25 | 24 hrs. | Thick Liquid | 1:1 | Not Rated | 0° to 300° | Aluminum | Machine, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Fiberglass | 10 | 0000000 | 00000 |
Surface Filler Patches
Knead the epoxy-coated patch and resin together to make repairs to pipes, tanks, drums, and containers in the field.
Lg. | Wd. | Begins to Harden, min. | Reaches Full Strength, hrs. | Mix Ratio | For Use Outdoors | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Surface Fillers | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
2" | 12" | 1 | 24 | 1:1 | Yes | -85° to 220° | Red | Sand | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Polystyrene Plastic, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Vinyl Plastic, EPDM Rubber, SBR Rubber, Fiberglass, Wood | 00000000 | 000000 |
2" | 20" | 1 | 24 | 1:1 | Yes | -85° to 220° | Amber | Machine, Sand | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Polystyrene Plastic, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Vinyl Plastic, EPDM Rubber, SBR Rubber, Fiberglass, Wood | 00000000 | 00000 |
4" | 6" | 1 | 24 | 1:1 | Yes | -85° to 220° | Blue | Machine, Sand | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Polystyrene Plastic, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Vinyl Plastic, EPDM Rubber, SBR Rubber, Fiberglass, Wood | 00000000 | 00000 |
4" | 12" | 1 | 24 | 1:1 | Yes | -85° to 220° | Green | Machine, Sand | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Polystyrene Plastic, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Vinyl Plastic, EPDM Rubber, SBR Rubber, Fiberglass, Wood | 00000000 | 00000 |
Pourable Surface Fillers
Make castings and fill voids with these two-part pourable epoxies. The size listed is the combined total of the two parts.
Certificates with a traceable lot number and product shelf life are available for these products. Download certificates from ORDER HISTORY after your order ships.
Container | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Net Weight, lbs. | Type | Begins to Harden, min. | Reaches Full Strength, hrs. | Consistency | Mix Ratio | Approximate Coverage @ Thick. | Max. Thick. | For Use Outdoors | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Loctite® Fixmaster Steel Liquid | |||||||||||||||
EA 3472 | 1 | Can | 25 | 24 | Thick Liquid | 4:1 | 50 sq. in. @ 1/4" | 1" | Yes | -20° to 220° | Gray | Machine, Tap | Bronze, Copper, Steel, Stainless Steel, Cast Iron, Concrete | 0000000 | 0000000 |
EA 3472 | 4 | Can | 25 | 24 | Thick Liquid | 4:1 | 200 sq. in. @ 1/4" | 1" | Yes | -20° to 220° | Gray | Machine, Tap | Bronze, Copper, Steel, Stainless Steel, Cast Iron, Concrete | 0000000 | 000000 |
Light-Activated Surface Fillers
Press these putty surface fillers in place to fill in holes, cracks, and dents. When exposed to sunlight or a UV lamp, they begin to harden immediately.
Epoxy fillers provide better adhesion and more corrosion resistance than polyester fillers.
Container | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Formulation | Size, fl. oz. | Type | Begins to Harden, sec. | Reaches Full Strength, min. | Consistency | For Max. Crack Wd. | Approx. Coverage @ Thick. | Max. Thick. | For Use Outdoors | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Polyester | 3.5 | Tube | 1 | 3 | Putty | 1" | 24 sq. in. @ 1/4" | 1/2" | Yes | -40° to 220° | White | Drill, Sand, Tap | Aluminum, Brass, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Fiberglass, Wood | 00000000 | 000000 |
Epoxy | 3.5 | Bottle | 1 | 5 | Putty | 1" | 24 sq. in. @ 1/4" | 1/2" | Yes | -40° to 270° | Amber | Drill, Sand, Tap | Aluminum, Brass, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Fiberglass, Wood | 00000000 | 00000 |
Water-Resistant Surface Fillers
Mix these two-part epoxy surface fillers to create a strong repair in wet environments or underwater. Use them to repair cracked, worn, and damaged surfaces. Size listed is the combined total of the two parts.
Putty fillers come in a stick with a resin on the outside and a hardener on the inside. Cut the desired amount from the sticks, knead to a uniform color to mix, and press into place. NSF/ANSI 61 surface fillers meet safety standards for use with drinking water.
Paste fillers resist alkalies, solvents, gasoline, and oil.
Container | ||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Size, fl. oz. | Net Weight, oz. | Type | Begins to Harden, min. | Reaches Full Strength | Consistency | Mix Ratio | Approx. Coverage @ Thick. | Max. Thick. | Temp. Range, °F | Color | Finishing Method | For Use On | Specifications Met | Each | |
Loctite® Fixmaster Metal Magic Steel | ||||||||||||||||
EA 3463 | __ | 4 | Stick | 3 | 24 hrs. | Putty | __ | 10 sq. in. @ 1/4" | 1" | -20° to 250° | Gray | Sand | Bronze, Copper, Steel, Stainless Steel, Cast Iron, Concrete | NSF/ANSI 61 | 0000000 | 000000 |
Loctite® Fixmaster Underwater Repair Epoxy | ||||||||||||||||
EA 9490 | __ | 4 | Stick | 15 | 60 min. | Putty | __ | 16 sq. in. @ 1/4" | 1/4" | Not Rated to 300° | White | Machine, Drill, Sand, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Polystyrene Plastic, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Fiberglass, Concrete, Wood | __ | 0000000 | 00000 |
Surface Fillers | ||||||||||||||||
__ | 12 | __ | Jar | 30 | 24 hrs. | Paste | 1:1 | 85 sq. in. @ 1/4" | 1" | 50° to 210° | White | Drill, Sand | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Polystyrene Plastic, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Fiberglass, Wood | __ | 0000000 | 00000 |
__ | 24 | __ | Can | 30 | 24 hrs. | Paste | 1:1 | 170 sq. in. @ 1/4" | 1" | 50° to 210° | White | Drill, Sand | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Polystyrene Plastic, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Fiberglass, Wood | __ | 0000000 | 00000 |
__ | 48 | __ | Can | 30 | 24 hrs. | Paste | 1:1 | 340 sq. in. @ 1/4" | 1" | 50° to 210° | White | Drill, Sand | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Polystyrene Plastic, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Fiberglass, Wood | __ | 0000000 | 00000 |
Fuel-Resistant Surface Fillers
Also known as sloshing compounds, these two-part epoxies bond to rough and rusty surfaces in fuel tanks to repair leaks and prevent further corrosion. They withstand permanent immersion in fuel, oil, and harsh solvents. Use them with metal, plastic, and fiberglass tanks. Mix the smaller can with the bigger one and pour into your fuel tank. Rotate the tank to coat the interior and dump out any excess. Allow to cure overnight. Size listed is the combined total of the two parts.
1.5-pint container can treat a 10-gallon fuel tank. 3-pint container can treat a 20-gallon fuel tank.
Container | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Size, pt. | Type | Begins to Harden, min. | Reaches Full Strength, hrs. | Consistency | Mix Ratio | For Use Outdoors | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
1.5 | Can | 5 | 24 | Thick Liquid | 2:1 | No | 70° to 90° | Amber | Drill, Sand, Tap | Aluminum, Brass, Bronze, Copper, Silver, Steel, Stainless Steel, Cast Iron, Galvanized Iron, Galvanized Steel, Titanium, Acrylic Plastic, Polycarbonate Plastic, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Nylon Plastic, Polyethylene Plastic, Polypropylene Plastic, Vinyl Plastic, Fiberglass, Ceramic, Porcelain | 0000000 | 000000 |
3 | Can | 5 | 24 | Thick Liquid | 2:1 | No | 70° to 90° | Amber | Drill, Sand, Tap | Aluminum, Brass, Bronze, Copper, Silver, Steel, Stainless Steel, Cast Iron, Galvanized Iron, Galvanized Steel, Titanium, Acrylic Plastic, Polycarbonate Plastic, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Nylon Plastic, Polyethylene Plastic, Polypropylene Plastic, Vinyl Plastic, Fiberglass, Ceramic, Porcelain | 0000000 | 00000 |
Surface Fillers for Metal
Mix these two-part surface fillers together to repair leaks and cracks as well as to rebuild rough spots in metal. The size listed is the combined total of the two parts.
Loctite EA 3471 and PC2 35642 have stronger adhesion than any other surface fillers we offer.
Use Loctite® Fixmaster Steel Epoxy with a dispensing gun and mixer nozzle to mix as you dispense.
Devcon Plastic Steel surface fillers can repair areas where brazing and welding is impractical.
NSF/ANSI 61 surface fillers meet safety standards for use with drinking water.
Surface fillers in a stick have a resin on the outside and a hardener on the inside. Cut the desired amount from the sticks, knead to a uniform color to mix, and press into place.
Container | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Size | Net Weight | Type | Begins to Harden, min. | Reaches Full Strength, hrs. | Consistency | Mix Ratio | Approx. Coverage @ Thick. | Temp. Range, °F | Color | Specifications Met | Finishing Method | For Use On | Each | |
Loctite® Fixmaster Steel Putty | |||||||||||||||
EA 3471 | __ | 1 lbs. | Jar | 30 | 24 | Thick Liquid | 2.5:1 | 40 sq. in. @ 1/4" | -20° to 220° | Gray | __ | Machine, Drill, Tap | Bronze, Copper, Steel, Stainless Steel, Cast Iron | 0000000 | 000000 |
EA 3473 | __ | 1 lbs. | Jar | 3 | 24 | Paste | 1:1 | 50 sq. in. @ 1/4" | -20° to 190° | Gray | __ | Machine, Drill, Tap | Bronze, Copper, Steel, Stainless Steel, Cast Iron | 0000000 | 00000 |
PC 235642 | __ | 4 lbs. | Can | 30 | 24 | Paste | 2.5:1 | 170 sq. in. @ 1/4" | -20° to 220° | Gray | __ | Machine, Drill, Tap | Bronze, Copper, Steel, Stainless Steel, Cast Iron | 0000000 | 000000 |
Loctite® Fixmaster Steel Epoxy | |||||||||||||||
PC 3965 | 1.7 fl. oz. | __ | Cartridge | 3 | 7 | Paste | 1:1 | 57 sq. in. @ 1/4" | -20° to 200° | Gray | __ | Machine, Drill, Sand, Tap | Bronze, Copper, Steel, Stainless Steel, Cast Iron | 000000 | 00000 |
Loctite® Fixmaster Stainless Steel Putty | |||||||||||||||
EA 3476 | __ | 1 lbs. | Jar | 20 | 24 | Paste | 4:1 | 30 sq. in. @ 1/4" | -20° to 220° | Gray | __ | Machine, Drill, Tap | Bronze, Copper, Steel, Stainless Steel, Cast Iron | 0000000 | 000000 |
Devcon Plastic Steel® Liquid | |||||||||||||||
10210 | __ | 1 lbs. | Jar, Can | 45 | 16 | Thick Liquid | 9:1 | 50 sq. in. @ 1/4" | -40° to 250° | Dark Gray | __ | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Copper, Stainless Steel, Cast Iron | 00000000 | 00000 |
10220 | __ | 4 lbs. | Jar, Can | 45 | 16 | Thick Liquid | 9:1 | 200 sq. in. @ 1/4" | -40° to 250° | Dark Gray | __ | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Copper, Stainless Steel, Cast Iron | 00000000 | 000000 |
Devcon Plastic Steel® Epoxy | |||||||||||||||
52345 | 2 fl. oz. | __ | Tube | 60 | 24 | Thick Liquid | 1:1 | 14 sq. in. @ 1/4" | -40° to 200° | Dark Gray | __ | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Copper, Stainless Steel, Cast Iron | 00000000 | 0000 |
Devcon Plastic Steel® Putty | |||||||||||||||
10110 | __ | 1 lbs. | Jar, Can | 45 | 16 | Putty | 9:1 | 40 sq. in. @ 1/4" | -40° to 250° | Gray | __ | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Copper, Stainless Steel, Cast Iron | 00000000 | 00000 |
10120 | __ | 4 lbs. | Jar, Can | 45 | 16 | Putty | 9:1 | 190 sq. in. @ 1/4" | -40° to 250° | Gray | __ | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Copper, Stainless Steel, Cast Iron | 00000000 | 000000 |
10130 | __ | 25 lbs. | Pail, Can | 45 | 16 | Putty | 9:1 | 1200 sq. in. @ 1/4" | -40° to 250° | Gray | __ | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Copper, Stainless Steel, Cast Iron | 00000000 | 00000000 |
Devcon Plastic Steel® 5 Minute Putty | |||||||||||||||
10240 | __ | 1 lbs. | Jar, Can | 5 | 16 | Putty | 1.7:1 | 40 sq. in. @ 1/4" | -40° to 200° | Dark Gray | __ | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Copper, Stainless Steel, Cast Iron | 00000000 | 000000 |
Permatex Black Plastic Welder | |||||||||||||||
84145 | 0.8 fl. oz. | __ | Syringe | 10 | 24 | Thick Liquid | 1:1 | __ | -60° to 250° | Black | __ | Machine, Drill, Sand, Saw, Tap | Aluminum, Stainless Steel, Cast Iron | 00000000 | 0000 |
Surface Fillers | |||||||||||||||
__ | __ | 4 oz. | Stick | 3 | 24 | Putty | __ | 16 sq. in. @ 1/4" | -40° to 250° | Dark Gray | NSF/ANSI 61 | Machine, Drill, Sand, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 0000000 | 00000 |
__ | __ | 16 oz. | Stick | 45 | 24 | Putty | __ | 64 sq. in. @ 1/4" | -40° to 250° | Off-White | __ | Machine, Drill, Sand, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 0000000 | 00000 |
Impact-Resistant Surface Fillers for Metal
These rubber-filled epoxies have excellent wear and impact resistance. Use them to repair and rebuild surfaces such as pump liners, hoppers, and vibrating feeders. The size listed is the combined total of the two parts.
Container | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Net Weight, lbs. | Type | Begins to Harden, min. | Reaches Full Strength, hrs. | Consistency | Mix Ratio | Approx. Coverage @ Thick. | Max. Thick. | For Use Outdoors | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Loctite® Nordbak High Impact Wearing Compound | |||||||||||||||
PC 9313 | 25 | Pail, Can | 30 | 6 | Paste | 2:1 | 1,240 sq. in. @ 1/4" | 1/4" | Yes | -20° to 250° | Gray | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 0000000 | 0000000 |
Fine-Particle Abrasion-Resistant Surface Fillers for Metal
For use in processing equipment that carries particles smaller than 1/16" in diameter, these ceramic-filled epoxies rebuild and repair surfaces exposed to abrasion from particles, such as dust collectors, fan blades, and fan housings. The size listed is the combined total of the two parts.
Container | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Net Weight, lbs. | Type | Begins to Harden, min. | Reaches Full Strength, hrs. | Consistency | Mix Ratio | Approx. Coverage @ Thick. | Max. Thick. | For Use Outdoors | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Loctite® Fixmaster Wear Resistant Putty | |||||||||||||||
PC 7222 | 1 | Jar | 30 | 24 | Putty | 2:1 | 50 sq. in. @ 1/4" | 1" | Yes | -20° to 220° | Gray | Sand | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 0000000 | 0000000 |
Loctite® Nordbak Pneu-Wear | |||||||||||||||
PC 7317 | 3 | Can | 30 | 6 | Paste | 4:1 | 150 sq. in. @ 1/4" | 1/4" | Yes | -20° to 250° | Gray | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 000000 | 000000 |
PC 7317 | 25 | Pail, Can | 30 | 6 | Paste | 4:1 | 1,240 sq. in. @ 1/4" | 1/4" | Yes | -20° to 250° | Gray | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 000000 | 000000 |
PC 7455 | 6 | Can | 10 | 3 | Paste | 2:1 | 310 sq. in. @ 1/4" | 1/4" | Yes | -20° to 220° | Blue | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 0000000 | 000000 |
Large-Particle Abrasion-Resistant Surface Fillers for Metal
For use in processing equipment that carries large particles 1/16" in diameter and larger, these ceramic-filled epoxies rebuild and repair surfaces exposed to abrasion from particles, such as pump housings, chute linings, and hoppers. The size listed is the combined total of the two parts.
Container | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Net Weight, lbs. | Type | Begins to Harden, min. | Reaches Full Strength, hrs. | Consistency | Mix Ratio | Approx. Coverage @ Thick. | Max. Thick. | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Loctite® Nordbak Wearing Compound | ||||||||||||||
PC 7218 | 5 | Jar, Can | 30 | 7 | Paste | 2:1 | 260 sq. in. @ 1/4" | 1/4" | -15° to 250° | Gray | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 000000 | 0000000 |
PC 7218 | 25 | Pail, Can | 30 | 7 | Paste | 2:1 | 1,240 sq. in. @ 1/4" | 1/4" | -15° to 250° | Gray | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 000000 | 000000 |
PC 7357 | 6 | Jar, Can | 25 | 8 | Paste | 2:1 | 310 sq. in. @ 1/4" | 1/4" | -20° to 250° | Gray | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 0000000 | 000000 |
PC 9599 | 6 | Jar, Can | 10 | 3 | Paste | 2:1 | 310 sq. in. @ 1/4" | 1/4" | -20° to 220° | Blue | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 000000 | 000000 |
High-Temperature Surface Fillers for Metal
Repair and rebuild metal surfaces that are exposed to heat. These surface fillers withstand temperatures over 450° F. Fillers that have a mix ratio are multi-part fillers. The size listed is the combined total of the parts.
Surface fillers in a stick have a resin on the outside and a hardener on the inside. Cut the desired amount from the sticks, knead to a uniform color to mix, and press into place.
Surface fillers in a syringe come with everything you need to make repairs.
Container | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Size, fl. oz. | Net Weight, oz. | Type | Begins to Harden | Reaches Full Strength, hrs. | Heating Requirements to Reach Full Strength | Consistency | Mix Ratio | Approx. Coverage @ Thick. | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Loctite® Fixmaster 2000° Putty | |||||||||||||||
MR 2000 | 8 | __ | Can | 30 min. | 7 | __ | Putty | __ | 30 sq. in. @ 1/4" | Not Rated to 2000° | Gray | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 0000000 | 0000000 |
Surface Fillers | |||||||||||||||
__ | __ | 4 | Stick | 90 min. | 72 | __ | Putty | __ | 16 sq. in. @ 1/4" | -40° to 450° | Gold | Drill, Sand, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 0000000 | 00000 |
__ | 1.5 | __ | Syringe | 20 min. | 24 | __ | Putty | 9.1:1 | 1 sq. in. @ 1/4" | -40° to 500° | Gray | Machine, Drill, Saw | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Fiberglass | 0000000 | 00000 |
__ | 8 | __ | Can | 5 hrs. | 6 | 2 hrs. air dry then 4 hrs. @ 200° F | Putty | __ | 32 sq. in. @ 1/4" | Not Rated to 2000° | Dark Gray | Sand | Steel, Stainless Steel, Cast Iron | 0000000 | 00000 |
__ | 16 | __ | Can, Bottle | 20 min. | 24 | __ | Putty | 9.1:1 | 10 sq. in. @ 1/4" | Not Rated to 500° | Gray | Machine, Drill, Saw | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Fiberglass | 0000000 | 00000 |
__ | 16 | __ | Bottle | 5 hrs. | 6 | 2 hrs. air dry then 4 hrs. @ 200° F | Putty | __ | 65 sq. in. @ 1/4" | Not Rated to 2000° | Dark Gray | Sand | Steel, Stainless Steel, Cast Iron | 0000000 | 000000 |
Chemical-Resistant Surface Fillers for Metal
Chemicals will not affect these two-part epoxies. They repair cracked, worn, and damaged surfaces. The size listed is the combined total of the two parts.
Container | ||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Size, fl. oz. | Net Weight, lbs. | Type | Begins to Harden, min. | Reaches Full Strength | Consistency | Mix Ratio | Approximate Coverage @ Thick. | Max. Thick. | For Use Outdoors | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Loctite® Fixmaster Superior Metal | ||||||||||||||||
EA 3478 | __ | 1 | Jar | 20 | 24 hrs. | Paste | 4:1 | 30 sq. in. @ 1/4" | 1" | Yes | -20° to 250° | Gray | Machine, Drill | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 0000000 | 0000000 |
Surface Fillers | ||||||||||||||||
__ | 11 | __ | Tube | 25 | 7 days | Paste | 1:1 | 50 sq. in. @ 1/4" | 1/4" | Yes | -55° to 180° | Silver | Machine, Drill, Sand, Tap | Aluminum, Brass, Bronze, Steel, Cast Iron, Titanium | 0000000 | 00000 |
Temporary Leak-Repair Sticks for Metal
Stop leaks in metal tanks and equipment without draining the contents. Until a permanent repair can be made, rub these sticks into the leak to form a temporary seal.
Container Net Weight, oz. | Begins to Harden, hrs. | Reaches Full Strength, hrs. | Formulation | Consistency | Max. Thick. | For Use Outdoors | Temp. Range, °F | Color | For Use On | Each | |
1.25 | 12 | 24 | Drying Oil | Putty | 1/8" | Yes | -50° F to 220° | Gray | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 000000 | 000000 |
High-Pressure Leak-Repair Sticks for Metal
To stop leaks in metal tanks and equipment without draining the contents, heat the area with a heat gun or torch to melt the stick and form a permanent seal. The resulting patch can withstand pressure up to 600 psi. These sticks meet NSF/ANSI 61 safety standards for use with drinking water systems.
Container Net Weight, oz. | Begins to Harden, min. | Reaches Full Strength, sec. | Temp. to Begin to Harden, °F | Consistency | Max. Thick. | For Use Outdoors | Temp. Range, °F | Color | Specifications Met | Finishing Method | For Use On | Each | |
0.375 | 1 | 90 | 250 | Putty | 1/8" | Yes | Not Rated to 350° | Green | NSF/ANSI 61 | Sand | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 000000 | 000000 |
Leak-Repair Sticks for Metal
To stop leaks in metal tanks and equipment without draining the contents, rub the smaller stick into the leak until it stops. Then, cut the desired amount from the larger stick, knead to a uniform color to mix, and press into place. The size listed is the combined total of the two parts.
Container Net Weight, oz. | Begins to Harden, min. | Reaches Full Strength, hrs. | Consistency | Mix Ratio | Max. Thick. | For Use Outdoors | Temp. Range, °F | Color | For Use On | Each | |
5.25 | 2 | 24 | Putty | 1:1 | 1/8" | Yes | -40° to 220° | Gray | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 0000000 | 000000 |
Sealant Primers
Prepare joints and surfaces to ensure proper sealant adhesion.
3M P592 primer cannot be sold to the listed regions due to volatile organic compound regulations.
Container | ||||||||
---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Size | Type | Drying Time | For Use On | Cannot Be Sold To | Choose a Color | Each | |
3M Primers | ||||||||
P591 | 8.5 fl. oz. | Bottle | 15 min. | Aluminum, Stainless Steel, Steel, Cast Iron, Galvanized Steel, ABS Plastic, Acrylic Plastic, Polycarbonate Plastic, Polystyrene Plastic, Polyurethane Rubber, PVC Plastic, Concrete, Glass, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Fiberglass, Wood, Iron, Galvanized Iron | __ | Black | 0000000 | 000000 |
P592 | 8.5 fl. oz. | Bottle | 15 min. | Aluminum, Stainless Steel, Steel, Cast Iron, Galvanized Steel, Iron, Galvanized Iron | Los Angeles County, CA; Orange County, CA; Riverside County, CA; San Bernardino County, CA; CT; DC; DE; MA; MD; ME; NJ; Northern VA; NY; PA; RI; UT; VT | Clear | 0000000 | 000000 |
Dow Corning Primers | ||||||||
P5200 | 12 fl. oz. | Bottle | 2 hrs. | Stainless Steel, Steel, Cast Iron, Galvanized Steel, ABS Plastic, Polycarbonate Plastic, Polystyrene Plastic, Polyurethane Rubber, PVC Plastic, Glass, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, EPDM Rubber, SBR Rubber, Ceramic, Masonry, Wood, Iron, Silicone Rubber, Galvanized Iron | __ | 00000000 | 000000 | |
PR-1200 | 10.9 fl. oz. | Bottle | 2 hrs. | Aluminum, Brass, Bronze, Copper, Stainless Steel, Steel, Titanium, Cast Iron, Galvanized Steel, ABS Plastic, Polycarbonate Plastic, Polystyrene Plastic, Polyurethane Rubber, PVC Plastic, Glass, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, EPDM Rubber, SBR Rubber, Ceramic, Masonry, Wood, Iron, Silicone Rubber, Galvanized Iron | __ | 00000000 | 00000 | |
PR-1205 | 12.3 fl. oz. | Bottle | 2 hrs. | Aluminum, Stainless Steel, Steel, Cast Iron, Galvanized Steel, ABS Plastic, Polycarbonate Plastic, Polystyrene Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Ceramic, Iron, Galvanized Iron | __ | Yellow | 0000000 | 00000 |
Contrast Paint for Magnetic-Particle Flaw Detection
Create a high-contrast background for magnetic particles to make flaws easier to spot during inspections. This opaque white paint reduces glare, so you can see where particles are clustered around imperfections. No need for brushes—it comes in an aerosol can that’s easy to use during field testing and spot inspections. Even when the can is upside down, the 360° sprayer won’t sputter or spatter, so you can coat parts evenly without straining your wrist. To speed up inspections, this paint dries quickly, leaving a clean coat that won’t bubble or flake. It works with both wet and dry magnetic particles.
Container | |||||||||
---|---|---|---|---|---|---|---|---|---|
Net Weight, oz. | Type | Composition | O'all Dry Time | Application Temperature Range, °F | For Use On | Color | Features | Each | |
Spray | |||||||||
12 | Aerosol Can | Solvent Based | 1 min. | 45° to 120° | Cast Iron, Cobalt, Iron, Nickel, Stainless Steel, Steel | White | 360° Sprayer | 0000000 | 000000 |