With a tighter bend radius than other petroleum hose, this hose can easily twist and turn around equipment.

Commonly used to transfer gasoline, this hose is also known as curb pump hose.

Transfer fuel oil with a hose that stays flexible in subzero conditions.

Cut the hose to your desired length and attach the fittings. You don't need any special equipment to install.

Heat chemicals to prevent them from freezing or becoming too thick. With a self-regulating heating wire, the liquid inside this hose stays warm and keeps flowing.

Attach push-on barbed fittings to this hose for use in low-pressure hydraulic applications. No clamps are needed to secure fittings to the hose; the more you pull on the fittings, the tighter the hose will grip.

Although only half the weight, this hose resists wear and tear 240 times better than our standard rubber hydraulic hose. The fittings come attached, so this hose is ready to connect to a male threaded fitting on one end and a female one on the other.

Although only half the weight, this hose resists wear and tear 240 times better than our standard rubber hydraulic hose. It comes with female threaded fittings already attached, so it’s ready to use right out of the box.

Use this hose to transfer fluid between pumps, cylinders, and other parts of your hydraulic system.

The new standard for rubber hydraulic hose, this hose bends twice as sharply and resists wear and tear 80 times better than our basic hydraulic hose.

The new standard for rubber hydraulic hose, this hose bends twice as sharply and resists wear and tear 80 times better than our basic hydraulic hose. The fittings come attached, so this hose is ready to connect to a male threaded fitting on one end and a female one on the other.

The new standard for rubber hydraulic hose, this hose bends twice as sharply and resists wear and tear 80 times better than our basic hydraulic hose. To save you time, it comes with male threaded fittings already attached.

For frequent connections, this hose has a socket end that's faster to connect and disconnect than a threaded fitting. This hose bends twice as sharply and resists wear and tear 80 times better than our basic hydraulic hose, thanks to its two layers of blended rubber.

To handle rapid changes in pressure and flow without bursting, this hose is reinforced with four steel wire spirals. It comes with male threaded fittings already attached, so it's ready to use right out of the box.

Prevent electrical shock and damage to equipment while moving hydraulic fluid near high voltages.

Commonly known as radiator hose, this hose is for low-pressure coolant applications.

Silicone rubber gives this hose, often called radiator hose, the ability to handle high-heat conditions.

Bend this hose in any direction and it won’t kink, even when routed through tight spaces.

Blue for cold and red for hot—this hose is color coded so you won’t mix up your coolant supply lines. Use it in data centers to connect servers to a cooling manifold.

Identify your air lines by color.

The rubber cover meets MSHA (Mine Safety and Health Administration) standards for flame resistance, so this hose is often used to transfer highly compressed air in robotic welding systems.

Made of EPDM rubber reinforced with steel wire so it handles high temperatures, this hose is often used to clean hard-to-reach areas or supply heat and moisture to processing equipment.

To prevent breaking down from contact with oil, animal fats, and grease as you wash down equipment with hot water, this hose is covered in blended rubber. It comes with fittings already attached, so it’s easy to connect to a washdown station and wash gun.

To transfer air or oil- and water-based paints, attach this hose to a paint-spray system that has separate hoses for air and paint. Fittings swivel until tightened for easy installation. Fittings with spring guards prevent kinking.

Dispense chemicals from a line that attaches and detaches from your drum or intermediate bulk container (IBC) in seconds. These nozzles and the included hose come with fittings that connect when you insert the plug into the socket and push the levers down.

The industry standard for fuel and lubricant applications, this tubing can be used intermittently with petroleum-based products without becoming hard or brittle.

This tubing is soft enough to handle continuous bending and flexing, yet tough enough to resist tearing and abrasion.

Made of highly chemical-resistant materials, this tubing withstands harsh chemicals such as hydrochloric acid, sodium hydroxide, and sulfuric acid.

With a diameter of 2" or larger, this tubing has the girth to handle high volumes of acids and other harsh substances.

Commonly used in applications requiring movement, such as metering (peristaltic) pumps and robotics, this tubing can handle continuous bending and flexing.

The corrugated design allows this tubing to extend and compress just like an accordion.

Not only can this tubing handle temperatures between -450° F and 500° F, it also has a convoluted spiral design for good flexibility and smooth flow.

A lightweight alternative to stainless steel, this tubing can handle extreme-pressure applications up to 1,000 psi.

Run chemicals through this tubing at temperatures between -100° F and 500° F.

Cold temperatures pose no problems for this tubing—it stays strong and flexible, even when temperatures drop to -100° F.

With hard walls and the ability to handle extreme temperatures, this tubing is the preferred material for semiconductor applications. The material contains extremely low levels of additives, so it won’t contaminate the fluid passing through it.

When your application does not require a smooth interior, this tubing is an economical choice.

This tubing is suitable for extreme-pressure applications reaching 15,000 psi—the highest pressure rating of all the tubing we offer.

A titanium additive gives this tubing excellent strength and superior corrosion resistance. It meets MIL-T-8808.

Also known as hypodermic or needle tubing, this tubing has thin walls and is made to tight tolerances for use in precision applications.

The outside of this tubing is polished to a high-luster finish for a shiny appearance.

Polished to a 10 Ra finish on the inside, this tubing has the smoothest interior of any tubing we offer. It is commonly used in semiconductor applications.

Bend this tubing into the shape you need without special tools or elbow fittings.

Unlike other aluminum tubing, this tubing is rigid and will not bend.

This tubing comes cleaned and capped to prevent moisture and dirt from contaminating the inside. It is also known as refrigeration and air conditioning tubing.

Tubing is welded with a smoothed weld bead on the inside to reduce particle buildup. It is also known as DOM (drawn over mandrel) tubing.

With the lowest OD tolerance of all our steel tubing, this tubing is designed for precision applications.