Wear-Resistant Nylon Balls
- Color: Off-White
- Temperature Range: Not Rated
- Tensile Strength: 11,200-12,300 psi (Good)
- Impact Strength: 0.6-1.4 ft.-lbs./in. (Poor)
- Hardness: Rockwell R108-R121 (Hard)
- For Use Outdoors: No
Use these nylon 6/6 balls as bearings and in sealing applications. They have a slippery surface that reduces wear caused by friction.
For technical drawings and 3-D models, click on a part number.
| Dia. | Dia. Tolerance | Pkg. Qty. | Pkg. | |
Inch | ||||
|---|---|---|---|---|
| 1/16 " | -0.002" to 0.002" | 100 | 0000000 | 000000 |
| 3/32 " | -0.002" to 0.002" | 100 | 0000000 | 0000 |
| 1/8 " | -0.001" to 0.001" | 100 | 0000000 | 0000 |
| 5/32 " | -0.001" to 0.001" | 100 | 0000000 | 0000 |
| 3/16 " | -0.001" to 0.001" | 100 | 0000000 | 0000 |
| 7/32 " | -0.001" to 0.001" | 100 | 0000000 | 0000 |
| 1/4 " | -0.001" to 0.001" | 100 | 0000000 | 0000 |
| 9/32 " | -0.001" to 0.001" | 100 | 0000000 | 00000 |
| 5/16 " | -0.001" to 0.001" | 100 | 0000000 | 00000 |
| 3/8 " | -0.001" to 0.001" | 100 | 0000000 | 00000 |
| 7/16 " | -0.002" to 0.002" | 100 | 0000000 | 00000 |
| 1/2 " | -0.001" to 0.001" | 50 | 0000000 | 00000 |
| 9/16 " | -0.001" to 0.001" | 50 | 0000000 | 00000 |
| 5/8 " | -0.002" to 0.002" | 10 | 0000000 | 0000 |
| 3/4 " | -0.001" to 0.001" | 10 | 0000000 | 0000 |
| 7/8 " | -0.001" to 0.001" | 10 | 0000000 | 00000 |
| 1 " | -0.001" to 0.001" | 5 | 0000000 | 0000 |
| 1 1/2 " | -0.002" to 0.002" | 1 | 0000000 | 0000 |
| 1 3/4 " | -0.002" to 0.002" | 1 | 0000000 | 00000 |
| 2 " | -0.002" to 0.002" | 1 | 0000000 | 00000 |
Metric | ||||
| 2 mm | -0.002" to 0.002" | 100 | 0000000 | 0000 |
| 5 mm | -0.001" to 0.001" | 100 | 0000000 | 00000 |
| 6 mm | -0.001" to 0.001" | 25 | 0000000 | 00000 |
Glow-in-the-Dark Threaded-Hole Ball Knobs
Expose these easy-to-grip ball knobs to light and they will glow green in the dark. Use them on control levers, push-pull rods, and emergency release handles. Made of plastic, all resist oil, grease, and solvents. Mount them on a threaded stud.
For technical drawings and 3-D models, click on a part number.
Unthreaded-Hole Ball Knobs
Tap custom threads or drill a hole in the side of the knob to secure with a set screw. These easy-to-grip ball knobs are good for control levers and push-pull rods. Made of plastic, all resist oil, grease, and solvents.
For technical drawings and 3-D models, click on a part number.
Stud-Mount Ball Transfers
Install these ball transfers in a threaded hole or use a nut to secure.
Nylon and polypropylene balls are nonmarking. Nylon is stronger than polypropylene. However, polypropylene resists chemicals better than nylon.
Ball transfers with an angled working orientation can be used to form support stands.
Capacity is given for the ball up orientation. Using these ball transfers in a ball down or angled orientation could reduce the capacity stated.
For technical drawings and 3-D models, click on a part number.
| Ball Dia. | Cap., lbs. | Ht. | Dia. | Working Orientation | Housing Color | Thread Size  | Stud Lg. | Temperature Range, °F | Each | ||
Nylon Plastic Ball | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
Zinc-Plated Steel Housing | |||||||||||
| A | 5/8" | 125 | 13/16" | 15/16" | Ball Up, Ball Down, Angle | __ | 1/4"-20 | 3/4" | 32° to 212° | 0000000 | 000000 |
| A | 1" | 200 | 1 1/4" | 1 3/8" | Ball Up, Ball Down, Angle | __ | 5/16"-18 | 3/4" | 32° to 212° | 0000000 | 00000 |
| C | 5/8" | 130 | 53/64" | 15/16" | Ball Up, Ball Down | __ | 1/4"-20 | 3/4" | __ | 00000000 | 00000 |
| C | 1" | 65 | 1 17/32" | 1 27/32" | Ball Up | __ | 1/4"-20 | 7/8" | 0° to 250° | 0000000 | 0000 |
| C | 1" | 440 | 1 1/4" | 1 1/2" | Ball Up, Ball Down | __ | 5/16"-18 | 3/4" | Not Rated to 1500° | 00000000 | 00000 |
| C | 1 1/2" | 250 | 2 5/16" | 2 3/16" | Ball Up, Ball Down | __ | 3/8"-16 | 1" | 32° to 212° | 0000000 | 00000 |
| D | 1" | 75 | 1 3/8" | 1 3/4" | Ball Up, Ball Down | __ | 1/4"-20 | 11/16" | 32° to 212° | 0000000 | 00000 |
| D | 1" | 75 | 1 3/8" | 1 3/4" | Ball Up, Ball Down | __ | 3/8"-16 | 11/16" | Not Rated to 125° | 00000000 | 00000 |
| D | 1" | 75 | 1 3/8" | 1 3/4" | Ball Up, Ball Down | __ | 5/16"-18 | 11/16" | 32° to 212° | 0000000 | 00000 |
| E | 1/2" | 65 | 11/16" | 7/8" | Ball Up, Ball Down | __ | 1/4"-20 | 3/4" | __ | 00000000 | 00000 |
| J | 3/4" | 40 | 31/32" | 1 9/32" | Ball Up, Ball Down, Angle | __ | M8 | 1 31/32" | -22° to 128° | 00000000 | 00000 |
| J | 1" | 55 | 1 9/32" | 1 9/16" | Ball Up, Ball Down, Angle | __ | M8 | 1" | -22° to 128° | 00000000 | 00000 |
Black-Oxide Steel Housing | |||||||||||
| K | 1" | 75 | 1 7/16" | 1" | Ball Up, Ball Down, Angle | __ | 1/4"-20 | 7/16" | Not Rated to 800° | 00000000 | 00000 |
| K | 1" | 75 | 1 7/16" | 1 7/32" | Ball Up, Ball Down | __ | 5/16"-18 | 11/16" | 32° to 212° | 0000000 | 00000 |
| K | 1 1/4" | 250 | 1 3/4" | 1 1/4" | Ball Up, Ball Down, Angle | __ | 3/8"-16 | 15/16" | Not Rated to 800° | 00000000 | 00000 |
Stainless Steel Housing | |||||||||||
| C | 5/8" | 130 | 53/64" | 15/16" | Ball Up, Ball Down | __ | 1/4"-20 | 3/4" | __ | 00000000 | 000000 |
| C | 1" | 65 | 1 17/32" | 1 27/32" | Ball Up | __ | 1/4"-20 | 7/8" | 0° to 250° | 0000000 | 00000 |
| C | 1" | 440 | 1 1/4" | 1 1/2" | Ball Up, Ball Down | __ | 5/16"-18 | 3/4" | __ | 00000000 | 000000 |
| D | 1" | 75 | 1 3/8" | 1 3/4" | Ball Up, Ball Down | __ | 1/4"-20 | 11/16" | 32° to 212° | 0000000 | 00000 |
| D | 1" | 75 | 1 3/8" | 1 3/4" | Ball Up, Ball Down | __ | 3/8"-16 | 11/16" | Not Rated to 125° | 00000000 | 00000 |
| D | 1" | 75 | 1 3/8" | 1 3/4" | Ball Up, Ball Down | __ | 5/16"-18 | 11/16" | 32° to 212° | 0000000 | 00000 |
| E | 1/2" | 65 | 11/16" | 7/8" | Ball Up, Ball Down | __ | 1/4"-20 | 3/4" | __ | 00000000 | 00000 |
Nylon Plastic Housing | |||||||||||
| N | 1" | 45 | 1 3/8" | 2 1/16" | Ball Up, Ball Down, Angle | Black | 5/16"-18 | 5/8" | 32° to 212° | 0000000 | 00000 |
Heavy Duty Stud-Mount Ball Transfers
Nylon balls are nonmarking.
Capacity is given for the ball up orientation. Using these ball transfers in a ball down or angled orientation could reduce the capacity stated.
For technical drawings and 3-D models, click on a part number.
Flange-Mount Ball Transfers
Nylon balls are nonmarking.
Ball transfers with an angled working orientation can be used to form support stands.
Capacity is given for the ball up orientation. Using these ball transfers in a ball down or angled orientation could reduce the capacity stated.
For technical drawings and 3-D models, click on a part number.
Flange | Mounting Hole | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Ball Dia. | Cap., lbs. | Ht. | Dia. | Working Orientation | Lg. | Wd. | No.of Mounting Holes | Dia. | Ctr.-to-Ctr. | Temperature Range, °F | Each | ||
Nylon Plastic Ball | |||||||||||||
Zinc-Plated Steel Housing | |||||||||||||
| A | 1" | 75 | 1 3/16" | 1 5/8" | Ball Up, Ball Down | 2 3/4" | 2" | 2 | 7/32" | 2 3/16" | 32° to 195° | 0000000 | 000000 |
| B | 1 1/2" | 250 | 1 13/16" | 2 19/32" | Ball Up, Ball Down, Angle | 3" | 3" | 4 | 9/32" | 2 7/16" | 32° to 195° | 0000000 | 00000 |
Stainless Steel Housing | |||||||||||||
| A | 1" | 75 | 1 3/16" | 1 11/16" | Ball Up, Ball Down, Angle | 2 3/4" | 2" | 2 | 7/32" | 2 3/16" | 32° to 195° | 0000000 | 00000 |
Shock-Absorbing Flange-Mount Ball Transfers
A thick rubber mounting cushion underneath these ball transfers absorbs impact and reduces vibration.
Nylon balls are nonmarking.
Ball transfers with an angled working orientation can be used to form support stands.
Capacity is given for the ball up orientation. Using these ball transfers in a ball down or angled orientation could reduce the capacity stated.
For technical drawings and 3-D models, click on a part number.
Flange | Mounting Hole | Pad | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Ball Dia. | Cap., lbs. | Ht. | Dia. | Working Orientation | Lg. | Wd. | No.of Mounting Holes | Dia. | Ctr.-to-Ctr. | Thick. | Material | Min. Temperature | Max. Temperature | Each | |
Nylon Plastic Ball | |||||||||||||||
Zinc-Plated Steel Housing | |||||||||||||||
| 1 1/2" | 250 | 1 13/16" | 2 19/32" | Ball Up, Ball Down, Angle | 3" | 3" | 4 | 9/32" | 2 7/16" | 1/4" | Neoprene Rubber | -30°F | 220°F | 0000000 | 000000 |
| 1 1/2" | 250 | 1 13/16" | 2 3/4" | Ball Up | 3" | 3" | 4 | 9/32" | 2 15/32" | 1/4" | Neoprene Rubber | Not Rated | 400°F | 0000000 | 00000 |
Stainless Steel Housing | |||||||||||||||
| 1 1/2" | 250 | 1 13/16" | 2 3/4" | Ball Up | 3" | 3" | 4 | 9/32" | 2 15/32" | 1/4" | Neoprene Rubber | Not Rated | 400°F | 0000000 | 00000 |
Press-Fit Ball Transfers
Drop-in design makes for easy installation.
Nylon balls are nonmarking.
Ball transfers with an angled working orientation can be used to form support stands.
Capacity is given in ball up orientation. Ball down or angled could reduce the capacity stated.
For technical drawings and 3-D models, click on a part number.
| Ball Dia. | Cap., lbs. | Ht. | Dp. | Dia. | Working Orientation | Flange Dia. | Temperature Range, °F | Each | ||
Nylon Plastic Ball | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
Zinc-Plated Steel Housing | ||||||||||
| A | 1/2" | 65 | 7/32" | 1/2" | 7/8" | Ball Up, Ball Down, Angle | 1/2" | 32° to 250° | 0000000 | 000000 |
| D | 5/8" | 125 | 3/8" | 13/16" | 15/16" | Ball Up, Ball Down, Angle | 1 3/16" | 32° to 212° | 0000000 | 00000 |
| D | 1" | 200 | 5/8" | 1 1/4" | 1 13/32" | Ball Up, Ball Down, Angle | 1 21/32" | 32° to 212° | 0000000 | 00000 |
| E | 5/8" | 130 | 7/32" | 7/16" | 15/16" | Ball Up, Ball Down, Angle | 1 1/4" | 32° to 250° | 0000000 | 00000 |
| E | 1" | 440 | 3/8" | 21/32" | 1 1/2" | Ball Up, Ball Down, Angle | 1 3/4" | 32° to 250° | 0000000 | 00000 |
Stainless Steel Housing | ||||||||||
| C | 5/8" | 20 | 3/8" | 7/16" | 15/16" | Ball Up, Ball Down, Angle | 1 7/32" | -20° to 175° | 0000000 | 00000 |
Heavy Duty Press-Fit Ball Transfers
Drop-in design makes for easy installation. When used at an angled working orientation, these ball transfers can be used to form support stands.
Nylon balls are nonmarking.
Capacity is given in ball up orientation. Ball down or angled could reduce the capacity stated.
For technical drawings and 3-D models, click on a part number.
Recessed Flange-Mount Ball Transfers
Transfers recess into the mounting surface for a low profile. These ball transfers can be used in an angled working orientation to form support stands. Nylon balls are nonmarking.
Capacity is given for the ball up orientation. Using these ball transfers in a ball down or angled orientation could reduce the capacity stated.
For technical drawings and 3-D models, click on a part number.
Flange | Mounting Hole | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Ball Dia. | Cap., lbs. | Ht. | Dp. | Dia. | Working Orientation | Lg. | Wd. | Dia. | No.of Mounting Holes | Dia. | Ctr.-to-Ctr. | Temperature Range, °F | Each | ||
Nylon Plastic Ball | |||||||||||||||
Zinc-Plated Steel Housing | |||||||||||||||
| A | 1" | 75 | 3/4" | 1/2" | 1 3/4" | Ball Up, Ball Down, Angle | 2 1/8" | 2 3/4" | __ | 2 | 7/32" | 2 3/16" | 32° to 195° | 0000000 | 000000 |
| E | 1" | 40 | 1/2" | 27/32" | 1 1/16" | Ball Up, Ball Down, Angle | __ | __ | 1 11/32" | 2 | 7/32" | 1 7/8" | __ | 00000000 | 00000 |
Wear-Resistant Plastic Pellets
With a low coefficient of friction, these pellets won't wear away from abrasion that’s often caused by contact with moving parts. Melt and mold them into desired shapes. All of these pellets are made from virgin resins and are compatible with various types of molding equipment, such as injection molders or 3D printers. They handle high temperatures without losing their mechanical properties.
Nylon pellets have good wear resistance, as well as chemical resistance against fuels and hydrocarbons. They will expand and contract when exposed to moisture and temperature changes.
Container | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Type | Net Weight, lbs. | Molding Temperature, °F | Melting Temperature, °F | Melt Flow Rate | Shrinkage | Hardness | Impact Strength | Tensile Strength | Coefficient of Friction | Clarity | Each | |
Nylon Plastic | ||||||||||||
Off-White | ||||||||||||
| Pail | 5 | 130° to 200° | 470° to 535° | Not Rated | 1.3-1.7% | Rockwell R115 (Hard) | 0.8 ft.-lbs./in (Poor) | 11,000 psi (Good) | 0.4 | Opaque | 0000000 | 0000000 |